Question about 2006 Cadillac Escalade

Open Question

2006 escalade rear liftgate will not lock. Not sure what the problem is. Is there a manual lock button?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2005 Tahoe Rear liftgate will

Doors unlock on 2005 Chevy Taho but the rear hatch won't. It does not even click when you press button. It does not have a key acess. Is there a manuel opener?? Or a fuse. Even the glass hatch will not unlock.

Posted on Sep 16, 2008

Ad
dgjtex
  • 405 Answers

SOURCE: 2006 chevy tahoe liftgate won't open when keyless remote unlocks

check fuse first always, then check connections fron rear gate to body.

Posted on Dec 15, 2008

  • 62 Answers

SOURCE: 2003 Saturn Vue rear liftgate won't open

The easy part is you just need the latch for the liftgate. The hard part is getting to it and opening the liftgate to replace the latch. You should be able to pull the liftgate trim off most of the way with the gate closed and try to manually actuate the latch to open the gate. You may have to go so far as breaking the latch from the inside to open the gate and then replace your latch.

Posted on Dec 17, 2008

  • 512 Answers

SOURCE: Remote Entry System not working, 05 Chrysler T&C

there is an update foe the body control module that will generally fix the problem. you will ned to take it to the dealer to have it done.

Posted on Jan 03, 2009

michigan man
  • 3533 Answers

SOURCE: liftgate will not unlock

if it was mine I would take the rear inside door panel off and see if there is any rust or bind in the power door lock motor itself and also make sure that no one has broken a key off or stuck anything in the lock cause I had an expedition with this same problem and it was a broken key in the lock

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of the rear liftgate relay for a 2005 cadillac escalade esv


I told you where it is . Relay for what ? lock , unlock ,what ??????
Here look it up yourself http://www.bbbind.com/free_tsb.html enter vehicle info year , make , model an engine . Under system click body & accessories .Under subsystem click power locks .Then click the search button ,then the blue link . Scroll down to second diagram .

Aug 20, 2017 | Cadillac Cars & Trucks

1 Answer

Envoy hatch lock


There is a known TSB for this....
#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Apr 14, 2014 | GMC Envoy XL Cars & Trucks

1 Answer

Rear liftglass won't lock


#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Jan 17, 2012 | 2009 Saab 9-7X

3 Answers

The rear lift gate on my 2006 Lincoln Navigator will not open automatically or manually and there appears to be no way to access anything inside the door from inside or out.


POWER LIFT-GATE OPERATION - To open the optional power liftgate, push the button on the instrument panel , press on your five-button key fob (if equipped), or press and release the control located in the left rear quarter panel (Figure B). To unlatch the liftgate glass, push the button ) under the center of the license plate lamp shield, or press on your five-button key fob. Do not open the liftgate or the liftgate glass in a garage or other enclosed area with a low ceiling. Keep clear of the liftgate when operating the rear switch. To open the liftgate manually, pull the handle located on the liftgate to release the liftgate from the vehicle. The power system will take over when you release the handle. To close, make certain the rear window is closed, and then pull down the liftgate a few inches to activate power closing. Closing the gate rapidly or more than a few inches may activate the obstacle detection feature and stop the power system.------------ Also click this link for more help:--- http://technoanswers.blogspot.com/2011/05/power-liftgate-on-will-not-open-on.html ------------ This should help.Keep updated.Thanks.Helpmech.

May 19, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

I accidently push the back liftgate on the Remote Keyless Entry. Even if the vehicle is locked and something in my purse hits the back liftgate button...it opens. Very power sensor as I have been on the...


Check with the dealer to see if you can get another remote keyless entry with a tailgate button more recessed back. It sounds like the button is too high on the pad and it needs to be recessed into the pad a bit more. Just trying to keep you safe.

Nov 28, 2010 | Cadillac Escalade EXT Cars & Trucks

1 Answer

When i use the key fob to lock the doors the back glass dont lock, ???????


This solution applies to models:
2002-2007 Chevrolet Trailblazer, Trailblazer EXT and Trailblazer SS
2004-2007 Buick Rainier
2002-2007 GMC Envoy, Envoy XL, and Envoy Denali
2002-2004 Oldsmobile Bravada
2005-2007 Saab 9-7x

Condition/Concern:
Rear liftgate glass will not lock when using the key fob or door switch unless the lock button is pressed a second time. All other doors will lock normally. This could be the result of the liftgate glass lock rod not adjusted correctly. This lock rod travels from the liftgate lock actuator to the glass release push-button cylinder.

Recommendation/Instructions:
Remove the inside rear liftgate trim panel. Disconnect the threaded lock rod clip at the end of the push-button glass release and rotate this clip 1 complete turn at a time making the lock rod longer. This will be the only threaded lock rod visible when the trim panel is removed and the liftgate is raised.
Note: For the rear glass to release, the rear liftgate latch must be in the closed position. For test purposes only, this latch can be made closed to make this lock rod adjustment.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

Apr 25, 2010 | 2006 Chevrolet Trailblazer

1 Answer

2001 Ford Escape Rear Hatch won't unlock


The liftgate consists of the following components:
  • liftgate door lock actuator
  • liftgate lock cylinder (if equipped)
  • liftgate window glass
  • liftgate window latch/ajar switch
  • liftgate window glass release handle
  • liftgate latch remote control which consists of the following component:
    • liftgate release handle
  • liftgate latch, which consist of the following component:
    • liftgate latch door ajar switch
Liftgate Latch Actuator Removal and Installation
  1. Remove the liftgate latch remote control. For additional information, refer to Liftgate Latch Remote Control in this section.
SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual
REMOVAL AND INSTALLATION Liftgate Latch Removal and Installation
  1. Remove the liftgate trim panel.
  1. Disconnect the liftgate ajar switch electrical connector.
  1. Disconnect the liftgate latch actuating rod.
    1. Open the clip.
    1. Disconnect the actuating rod.
  1. Remove and discard the liftgate latch bolts.
  1. Remove the liftgate latch.
  1. NOTE: Make sure the liftgate latch release rod is not preloading the latch. It should be clipped in a relaxed state with no slack.
    NOTE: Position the liftgate latch release rod by pushing outboard to remove the slack.
  1. Remove the screws and the liftgate latch actuator
90f640f.gif

May 29, 2009 | 2001 Ford Escape

1 Answer

Liftgate will not unlock when i use power lock or the remote keyless entry transmitter. I checked the fuse LOCKS (rear doors and liftgate power lock relay feed) it is fine. The rear doors do unlock using...


if it was mine I would take the rear inside door panel off and see if there is any rust or bind in the power door lock motor itself and also make sure that no one has broken a key off or stuck anything in the lock cause I had an expedition with this same problem and it was a broken key in the lock

Jan 05, 2009 | 2004 Cadillac Escalade

1 Answer

Cannot lock liftgate


There is an electric motor inside the lift gate that has failed, it pulls the lock rod down to lock the gate when you press the remote, pull the lift gate trim panel and replace thiws part.

Oct 07, 2008 | 2006 Cadillac Escalade

Not finding what you are looking for?
2006 Cadillac Escalade Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...