Question about Chevrolet Suburban

1 Answer

My wipers wont shut off on Chevy suburban 2004, the speeds change and washer fluid works stil but wont shut off. i pulled the fuse out for now. ThankYou ,

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 749 Answers

A shorted multifunction switch is the most likely cause for this type of issue. This will require replacement of the switch.

Posted on Sep 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

2 Answers

2003 chevy suburban windshield wiper do not work in low speeds, but in hight speed


Have someone check the connections from the harness connector to the wiper control board to see if the solder joints have deteriorated. Might need to be re-soldered.

May 04, 2014 | 1999 Chevrolet Suburban

2 Answers

My wiper will work but it will not spray washer fluid anymore. Any suggestions?


CHECK WIPER FLUID LEVEL FIRST ALL IS GOOD CHECK FOR POWER AT WIPER WASHER PUMP MOTOR.IF NO POWER AT WIPER WASHER MOTOR.CHECK 15 AMP FUSE IN THE ENGINE COMPARTMENT FUSE RELAY BOX.IF YES YOU ARE GETTING POWER AT WIPER WASHER MOTOR.WIPER WASHER MOTOR FAULTY.

Dec 31, 2010 | 2004 Chevrolet Suburban

1 Answer

Rear windshield washer motor works, but no fluid comes out


Rear washer may have it's own reservoir . Can you hear a pump humming when you activate the washer? Look in the under flooor compartment

Mar 22, 2009 | 1997 Chevrolet Suburban

1 Answer

The Rear Wipers on my 2001 1500 Chevy Suburban Stopped working


Unplug the connector at the rear wiper motor, turn the switch on and probe the wires with a test lamp, if you have power back there you more than likely have a bad motor. If there is no power start checking fuses they are all labeled easily on the back side of the fuseblock covers both on the dash and underhood. Good Luck!!!

Mar 15, 2009 | 2001 Chevrolet Suburban

4 Answers

Windshield Wiper Not Working Properly


Well sure enough all I had to do was replace the circuit board...wish I had done this a couple months ago...it was so easy to do and will now be much easier to drive with being able to see clearly again....

Dec 22, 2008 | 1999 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...