Question about Toyota Pickup

1 Answer

Fitting front wheel bearings for 2006 4x4 hilux

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,036 Answers

FRONT WHEEL BEARINGS MORE LIKELY HAS TO BE PRESSED IN.

Posted on Sep 04, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Healeyman
  • 1198 Answers

SOURCE: front wheel bearing removal on 2006 F350 touchtone 4X4

Get a good repair manual. Front ends on 4X4s require proper care.

Posted on Apr 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fit front wheel bearings Which brand to use for quality


If the car is front wheel drive a puller is required to dismantle the hub a rather involved job better left to a mechanic .If rear wheel drive do the following. ( Applies to front wheel drive also.) Chock rear wheels,loosen front wheel nuts, jack up car, fit safety stands,remove wheel , remove grease cap from axle. remove split pin or locking nut on axle ,Remove hub, with a punch drive out the grease seal ,the tapered cone bearings can now be removed, the 2 bearing cups still in the housing will have to be pressed out ,all old grease has to be cleaned out. the new cones must be repacked with high temp bearing grease . tap in the seal with the lip facing inwards , slide on the hub fit the outer cone to the axle , the spacer and nut goes on next, tighten the nut to seat the bearings , spin the hub make sure its free to spin, back off the nut one eighth of a turn fit a new split pin or lock tab. fit grease cap and road wheel.

Jul 27, 2014 | Cars & Trucks

1 Answer

2007 toyota hilux 4x4. Bad whining and vibrations in front end while driving. Feels like front diff trying to lock in. Any ideas. Taken to few 4x4 mechanics they say never heard of it before!!!


check the bushes / bearings that are in the end of the diff housing for shaft wear. Check the cv joints for wear. check shafts for bent . check front wheel bearings and adjustment. Check the drive shaft from the transmission to the front diff as they are prone to u-joint failure and excessive wear in the slip joint.

Dec 26, 2013 | Cars & Trucks

1 Answer

Torque specs bearing


Honestly you should search google. It is right there. the inner hub nut must be torqued to 59 Nm rotate the hub three times in each direction and then loosen the inner hub nut until it can be turned by hand, then again tighten the inner hub nut to 25 Nm. the lockwasher against the inner hub nut, it only goes in one way, it has a small inner tab that locates with the key way of the hub, this is between the threads. Once the lock washer is in the correct position, you can now install the outer hub nut, this outer nut must be torqued to 47 Nm, once you have tightened this outer nut, please once again check that the starting effort is correct.

Oct 18, 2013 | 2007 Toyota Hilux 2.5

1 Answer

I am getting a pulsing feeling from the front wheels when braking on my 2004 Chrysler Sebring. It feels like one or more of the rotors are warped. How do I replace the front rotors with new ones. Thanks.


If they are not worn beyond tollerance they can be machined on the vehicle.
Also make sure its not tyres or wheel bearings.

remove wheel
remove brake caliper( leave the hose connected)
remove centre cap
remove split pin and lock
unscrew bearing hub nut
rotor should come off
fit new bearing races in new rotor
grease new bearings
fit inside bearing and seal
refit rotor, outer bearing,washer,nut,lock, splitpin and centre cap
(tighten nut until no play in bearing plus 1\8 of a turn)
refit caliper and wheel
bleed and test brakes before driving

Apr 28, 2010 | 2004 Chrysler Sebring

2 Answers

VAGUE AND WANDERING STEERING ON 1990 HILUX 4 X4


Wandering is usually caused by toe-out. Did the aligner use front wheel drive specifications for this rear wheel drive truck? A front wheel drive toes in when the wheels are pulling the car, but the front wheels on your truck drag back to a toe-out position if steering parts are worn. Try pushing the fronts of the front wheels apart. They should still be at least a 16th of an inch closer in the front than in the rear of the tires.

Sep 10, 2009 | 1990 Toyota Pickup

1 Answer

Replace front wheel bearings 99 ford explorer


not press fitted, standard tapered bearings, if 4X4 it is a little more involved, just dont misplace any of the smaller parts and you will be fine.

Aug 29, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...