Question about 2002 Chevrolet Malibu

1 Answer

How do I replace a signal switch. Does this need to be taken in for service or is it something that can be done at home.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 222 Answers

Just got to take apart the steering column cover to get to it. Not real hard but read a manual if you haven't done it before. Be very careful if you have an airbag. Do not let any wire touch anything else. Also the ignition switch is very close. Just read up on it and then take take your time when doing.

Posted on Sep 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine firing issue whilst driving and using left indicator (only) what could be the fault?


Have they checked for a short in the steering column where the signal switch and ignition wires may be touching or shorting together.

Jul 15, 2015 | Cars & Trucks

3 Answers

How to replace my turn signal switch


Multi-function Switch Removal & Installation To Remove:
To Remove:
  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the turn signal and multifunction switch connectors out from the bulk head connector.
  4. Remove the two mounting screws and remove the multi-function switch from the steering column.

To Install:
  1. Install the multi-function switch on the steering column.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  3. Install the harness in the original retainers.
  4. Install the steering column trim covers.
7f81df3.gif

Jun 25, 2009 | 1996 GMC Sierra

2 Answers

Tilt Steering Wheel has up and down movement no matter what position it is in. I bought this truck new and I know this isn't normal.This just started about a month ago. Is this something that should be...


there are some bolts in the column that work loose in the chevrolet columns. they are a pain to get to most of the time is easier to replace the entire column with one from the salvage yard that still feels tight.

Jun 24, 2009 | 1991 Chevrolet C1500

1 Answer

Gas tank


You need to replace the fuel tank switch. This is a common problem with the Fords. The switch is about $40.00.

Mar 18, 2009 | 1992 Ford F150 SuperCab

2 Answers

Turn signals not working...put on right signal and left goes off


hi there , there must be a fried wire in the relay box were the two relays are for the turn signals. or a bad relays and the other acts for both . hope this could help ya.

Jan 05, 2009 | 2005 Chrysler Town & Country

1 Answer

Need special tool for 1993 Buick Regal


you will need a lock plate tool once you have taken the lock plate off you need to take the three screws out of the turn signal switch and unscrew the turn signal handle. when you have done this do not pull it out yet. you need to go under the dash and look for the group of wires that run up your steering column. you'll have to unplug them to get enough wire to lift the turn signal switch out. Do not pull these wires all the way out just enough to lay the thing out of the way. Ok once thats done right above the ignition tumblers is either a screw or a tiny indent hole you will have to knock open hopefully its just a screw that just holds it in.
Ok thats enough for now

One other thing the emergency flasher switch has one screw in the middle just unscrew it

Nov 15, 2008 | 1993 Buick Regal

Not finding what you are looking for?
2002 Chevrolet Malibu Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...