Question about 1995 Ford Crown Victoria

1 Answer

I need a diagram for the electric windows. The cable link is disconnected and i need to see how it goes back on.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 116 Answers

You may need a new regulator, generally if the cable is off, its broken. most parts stores will stock this, as it is a common problem.

Posted on Sep 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove the left rear door panel from a 1996 Nissan Maxima? The window just fell down. It can be manually lifted up, but it slides back down again. It no longer mechanically works. If you can...



  • Disconnect the negative battery cable(for safety if you have power locks and windows)
  • At the bottom of the door panel remove the two screws
  • Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector
  • Remove the inside door handle
  • Remove the screw in the door pull pocket
  • Pull the door panel away from the door far enough to disconnect the electrical connectors

May 23, 2011 | 1996 Nissan Maxima

1 Answer

I have a 1997 Buick LeSabre and none of the electric window switches are working except the rear passenger switch. The rear driver switch was working but it stopped with the window down. I want to get...


Take off the door panel and disconnect the two wire plug one is brown the other is orange. Take two jumper wires and run them to a battery. If it goes down then switch the wires on the battery and it will go up. If it does not move then the window motor is shot and will need to be replaced.

Mar 13, 2011 | 1997 Buick LeSabre

1 Answer

I need to replace the driver's side brake light.


Rear Combination Light- 2007 might vary from these diagrams:
Removal & Installation 2004 (Early Production) 4 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear Combination Light kia-06-18-7495.gif

  3. Remove 2 screws and 2 nuts and remove light assembly.
To Install:
  1. Install light assembly and 2 screws and 2 nuts.
  2. Connect electrical connector.
  3. Connect battery negative cable.
5 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear combination light kia-06-18-7496.gif

  3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
    Use care to not damage gasket.
  4. Pull rear combination light from vehicle.
To Install:
  1. Install rear combination light and 2 screws.
  2. Install 2 screws.
  3. Connect electrical connector.
  4. Connect battery negative cable.
2004 (Late Production), 2005-2009 To Remove:
Turn Signal Lamp kia-06-20-7698.gif

  1. Disconnect battery negative cable.
  2. Remove 2 screws and cover inside trunk.
  3. Remove 4 nuts and disconnect electrical connector (A).
  4. Remove rear combination lamp.
To Install:
Turn Signal Lamp kia-06-20-7698.gif

  1. Install rear combination lamp.
  2. Install 4 nuts and connect electrical connector (A).
  3. Install cover inside trunk and install 2 screws.
  4. Connect battery negative cable.
prev.gif next.gif

Oct 28, 2010 | 2007 Kia Spectra5

1 Answer

1996 Lincoln Town Car drivers power window wont go up or down. Took door panel apart. There is a cable broke but not sure how to replace or where it goes.


SOUND LIKE POWER WINDOW ELECTRICAL CABLE BROKEN.TO FIND WHERE IT GOES YOU NEED A ELECTRICAL DIAGRAM IN HAYNES REPAIR TO FIX THE ELECTRICAL CABLE.

Mar 27, 2010 | Lincoln Zephyr Cars & Trucks

2 Answers

How do I change a 2005 mustang alternator? NOT gt


2005 Ford Mustang 4.0L SFI SOHC 6cyl
Ford Mustang 1999-2005
Alternator - Removal & Installation

3.8L And 4.0L Engines
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belt.
  4. Disconnect the alternator electrical connectors.
  5. Remove the alternator shield (4.0L engine).
  6. Remove the alternator mounting bolts.
  7. Remove the alternator from the vehicle.
  8. Installation is the reverse of the removal procedure.
To install:
  1. Position the alternator onto engine. Tighten the lower bolt to 35 ft. lbs. (47 Nm) and the upper bolt to 18 ft. lbs. (25 Nm).
  2. Install the alternator shield (4.0L engine).
  3. Connect the alternator electrical connectors.
  4. Install the accessory drive belt.
  5. Connect the negative battery cable.

4.6L Engines (Non-Supercharged)
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the air intake scoop bracket, if equipped.
  4. Remove the accessory drive belt.
  5. Remove the upper alternator bracket.
  6. Disconnect the alternator electrical connectors.
  7. Remove the alternator bolts.
  8. Remove the alternator from the vehicle.
  9. Installation is the reverse of the removal procedure.
To install:
  1. Position the alternator onto engine. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).
  2. Connect the alternator electrical connectors.
  3. Install the upper alternator bracket. Tighten the bolts to 89 inch lbs. (10 Nm).
  4. Install the accessory drive belt.
  5. Install the air intake scoop bracket, if equipped.
  6. Connect the negative battery cable.
4.6L Engines (Supercharged)
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belt.
  4. Raise the vehicle.
  5. Disconnect the alternator electrical connectors.
  6. Remove the alternator bolts.
  7. Remove the alternator from the vehicle.
  8. Installation is the reverse of the removal procedure.
To install:
  1. Position the alternator onto engine. Tighten the lower bolt to 18 ft. lbs. (25 Nm) and the upper bolt to 37 ft. lbs. (50 Nm).
  2. Connect the alternator electrical connectors.
  3. Lower the vehicle.
  4. Install the accessory drive belt.
  5. Connect the negative battery cable.
  6. Installation is the reverse of the removal procedure.

More details about this model in Autozone.com (free register).

I hope help you with this (remember rated this help). Good luck.

Sep 17, 2009 | 2005 Ford Mustang

2 Answers

Electric window cable diagram


you need to buy a new window regulator

Jun 24, 2009 | 1998 Buick Regal

1 Answer

Disconnected wires - electric windows won't work


Go to local library and get the diagram (if they have a hanes manual etc). If not go to nissan dealer and fork out the 100 dollars for the shop manual. Best investment you will ever make.

Jun 03, 2009 | 2004 Nissan Sentra

1 Answer

Need to replace alternator


Here's a link to the alternator diagram:

http://www.chiltonlibrary.com/content/images/0601/images/06017-FREE-g02.gif

Instructions:
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Rotate the drive belt tensioner counterclockwise and remove the accessory drive belt.
  4. Remove the right lower splash shield.
  5. Disconnect the crankshaft position sensor.
  6. Disconnect the wiring harness locators from the alternator splash shield.
  7. Detach the alternator wiring connector.
  8. Remove the positive cable nut.
  9. Remove the alternator splash shield and the alternator.
Here's a link to a website to put the serpentine back on, just insert the year,make,model, and engine size to get the "Routing Diagram" for your car.

http://www.mvreader.com/multiview/dayco/index.php?bgInterchange=1&l=n

All the best on your repair.
Greg


May 30, 2009 | 2005 Mercury Montego

1 Answer

The electric window cable of my 1993 has come off.


this cannot be repaired. the window regulator assy needs to be replaced

Feb 12, 2009 | 1993 Mercury Grand Marquis

Not finding what you are looking for?
1995 Ford Crown Victoria Logo

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...