Question about 2001 Cadillac DeVille

1 Answer

The plenum boot between the intake manifold and throttle body is leaking vacuum. How do I get it out to replace?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,190 Answers

Hello, You have to remove the intake manifold.

Posted on Sep 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1998volvo s70 idles rough acceleration is fine


Sounds like it may have a vacuum leak, recommend geting a can of carb cleaner and spray around throttle body and intake , see if idle changes

Mar 25, 2015 | 1998 Volvo S70

2 Answers

Antifreeze getting into throttle body


The 3.8 liter for this year has a plastic intake manifold. These manifolds are known to fail around the EGR port. When this happens coolant will leak into the intake right behind the throttle body. Dorman makes a replacement upper plenum that has been reinforced in this problem as along with a new gasket and an updated EGR tube. This will more than likely solve your issue. If you see a little coolant behind the throttle body this repair needs to be done ASAP. If this area completely ruptures it will hydroloc the engine. This means that coolant will fill one or more of the cylinders and the engine will not turn over/start.

Nov 03, 2012 | 1998 Oldsmobile 88

2 Answers

How to replace a intake plenum gasket


Well basically, you remove the intake plenum and replace the gasket and reinstall the plenum. Here are the steps:

1. Disconnect the negative battery cable from the remote jumper terminal located at the right strut tower.
2. Remove the air inlet resonator and tube.
3. Remove the throttle actuator cables from the throttle arm and bracket.
4. Disconnect Secondary Runner Valve (SRV), Manifold Tuning Valve (MTV), Throttle Position Sensor (TPS), Idle Air Control (IAC) motor electrical connectors.
5. Remove the electrical connector and the Intake Air Temperature/Manifold Absolute Pressure (TMAP) sensor.
6. Disconnect vacuum hoses from the Secondary Runner Valve (SRV) reservoir, Speed Control reservoir, and PCV.
7. Remove right and left intake manifold supports.
8. Remove support brackets at the intake manifold front corners and MTV.
9. Loosen upper fastener attaching throttle body to support bracket.
10. Remove clips attaching EGR tubes to intake manifold.
11. Remove intake manifold bolts and manifold
12. Remove old gaskets, Clean gasket surfaces, and install new gaskets.
13. Reverse steps to reinstall manifold

Jun 16, 2012 | 1999 Chrysler 300M

1 Answer

Intakegasket for grandam gt


Exactly what is the wrong? Need the part? Need to know torque adjust or porcedure to take off?

For
1994 Pontiac Grand Am 3.1L SFI OHV 6cyl check this procedure for Intake Manifold...
(see Figure 14)
The 3.1L engine is equipped with upper and lower intake manifolds. The upper intake manifold is also known as the intake manifold plenum.

CAUTION The fuel system is under pressure and must be properly relieved before disconnecting the fuel lines. Failure to properly relieve the fuel system pressure can lead to personal injury and component damage.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove top half of the air cleaner assembly and throttle body duct.
  4. Drain and recycle the engine coolant.
  5. Disconnect the EGR pipe from exhaust manifold.
  6. Remove the serpentine belt.
  7. Remove the brake vacuum pipe at the intake plenum.
  8. Disconnect the control cables from the throttle body and intake plenum mounting bracket.
  9. Remove the power steering lines at the alternator bracket.
  10. Remove the alternator.
  11. Label and disconnect the ignition wires from the spark plugs and wire retainers on the intake plenum.
  12. Remove the ignition assembly and the EVAP canister purge solenoid together.
zjlimited_601.jpg

Fig. 14: View of the intake manifold and related components

  1. Disconnect the upper engine wiring harness connectors at the following components:
    Throttle Position Sensor (TPS) Idle Air Control (IAC) Fuel Injectors Coolant temperature sensor Manifold Absolute Pressure (MAP) sensor Camshaft Position (CMP) sensor
  2. Tag and disconnect the vacuum lines from the following components:
    Vacuum modulator Fuel pressure regulator PCV valve
  3. Disconnect the MAP sensor from upper intake manifold.
  4. Remove the upper intake plenum mounting bolts and lift off the plenum.
  5. Disconnect the fuel lines from the fuel rail and bracket.
  6. Install engine support fixture special tool J 28467-A or an equivalent.
  7. Remove the right side engine mount.
  8. Remove the power steering mounting bolts and support the pump out of the way without disconnecting the power steering lines.
  9. Disconnect the coolant inlet pipe from the outlet housing.
  10. Remove the coolant bypass hose from the water pump and the cylinder head.
  11. Disconnect the upper radiator hose at thermostat housing.
  12. Remove the thermostat housing.
  13. Remove both rocker arm covers.
  14. Remove the lower intake manifold bolts. Make sure the washers on the four center bolts are installed in their original locations.
When removing the valve train components they should be kept in order for installation the original locations.
  1. Remove the rocker arm retaining nuts or bolts and extract the rocker arms and pushrods.
  2. Remove the intake manifold from the engine. Remove and discard the gasket.
  3. Using a suitable scraper, clean gasket material from all mating surfaces. Remove all excess RTV sealant from front and rear ridges of cylinder block
To install:
  1. Place a 0.12 inch (3mm) bead of RTV, on each ridge, where the front and rear of the intake manifold contact the block.
  2. Using a new gasket, place the intake manifold on the engine.
  3. Install the pushrods in their original locations. Coat the pushrods with prelube.
The intake pushrods are marked yellow (5 3 /4 inch long) and the exhaust are green (6 inches long). Make sure the pushrods are properly seated in the valve lifters and rocker arms.
  1. Position the rocker arms in there original locations and tighten to specifications. Refer to the procedure earlier in this section.
  2. Install lower the intake manifold attaching bolts. Apply sealant 12345739 (or equivalent thread locking compound) to the threads of bolts. Tighten the vertical bolts first then the diagonal bolts to 115 inch lbs. (13 Nm).
  3. Install the front rocker arm cover.
  4. Install the thermostat housing.
  5. Connect the upper radiator hose to the thermostat housing.
  6. Fasten the coolant inlet pipe to thermostat housing.
  7. Connect coolant bypass pipe at the water pump and cylinder head.
  8. Install the power steering pump in the mounting bracket.
  9. Loosely install the serpentine belt.
  10. Connect the right side engine mount.
  11. Remove the special engine support tool.
  12. Fasten the fuel lines to fuel rail and bracket.
  13. Install the upper intake manifold and tighten the mounting bolts to 18 ft. lbs. (25 Nm).
  14. Install the MAP sensor.
  15. Connect the upper engine wiring harness connectors to the related components removed earlier.
  16. Connect the vacuum lines to the PCV, vacuum modulator and fuel pressure regulator.
  17. Install the EVAP canister purge solenoid and ignition assembly.
  18. Install the alternator assembly.
  19. Connect the power steering line to the alternator bracket.
  20. Install the serpentine belt.
  21. Connect the spark plug wires to the spark plugs and intake plenum wire retainer.
  22. Install the EGR pipe to the exhaust manifold.
  23. Attach the control cables to the throttle body lever and upper intake plenum mounting bracket.
  24. Install air intake assembly and top half of the air cleaner assembly.
  25. Install the brake vacuum pipe.
  26. Fill the cooling system.
  27. Connect the negative battery cable, then start the vehicle and verify that there are no leaks.

For PARTS REPLACEMENT check in THIS LINK: carpartswholesale.com

Hope helps.

Feb 01, 2011 | 1994 Pontiac Grand Am

1 Answer

How to remove intake manifold on 2005 Buick Lesabre


You didn't post the size of your engine so please pick the appropriate one:

3.8L
  1. Relieve the fuel system pressure.
  2. Drain the cooling system.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Supercharger
    • Thermostat housing
    • Exhaust Gas Recirculation (EGR) tube at the intake manifold
    • Engine Control Temperature (ECT) sensor
    • Intake manifold
  • To install:

    1. Install or connect the following:
      • Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm).
      • ECT sensor connector
      • EGR tube to the intake manifold
      • Thermostat housing
      • Supercharger
      • Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.
    4.6L
    4.6L Engine
    1. Remove the brake booster hose from the throttle body.
    2. Remove the fuel pressure regulator vacuum tube from the fuel pressure regulator and the water crossover.
    3. Remove the PCV fresh air feed tube from the camshaft cover and the throttle body.
    4. Remove the PCV dirty air tube from the PCV orifice in the right camshaft cover and from the intake manifold.
    5. Disconnect the fuel injector electrical connectors from the fuel injectors.
    6. Remove the fuel injector wiring harness.
    7. Remove the fuel rail bracket nut from the engine lift bracket.
    8. Remove the fuel rail studs.
    9. Lift and remove the fuel rail with injectors.
    10. Loosen the plenum duct clamp in order to remove the intake manifold.
    11. Remove the intake manifold bolts.
    12. Remove the intake manifold.

    To install:

    1. Install the intake manifold, fitting the plenum duct over the intake manifold duct.
    2. Loosely install the intake manifold bolts.

    // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 45; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_21.gif

    Intake manifold torque sequence-4.6L engine


    1. Tighten the intake manifold bolts in sequence. Tighten the intake manifold bolts to 89 inch lbs. (10 Nm).
    2. Tighten the plenum duct clamp to the intake manifold. Tighten the plenum duct clamp to 24 inch lbs. (2.75 Nm).
    3. Inspect the fuel injector O-rings. Ensure the fuel injector O-rings are not missing, misaligned or damaged. Replace the O-rings if necessary.
    4. Lubricate the intake manifold fuel injector bores with light mineral oil (GM P/N 9981704), clean engine oil, or equivalent.
    5. Install the fuel rail with fuel injectors as an assembly.
    6. Install the fuel rail studs. Tighten the fuel rail studs to 80 inch lbs. (9 Nm).
    7. Install the fuel rail bracket nut to the engine lift bracket. Tighten the fuel rail bracket nut to 89 inch lbs. (10 Nm).
    8. Install the fuel injector wiring harness.
    9. Connect the fuel injector electrical connectors to the fuel injectors.
    10. Install the PCV dirty air tube to the PCV orifice in the right camshaft cover and to the intake manifold.
    11. Install the PCV fresh air feed tube to the camshaft cover and the water crossover.
    12. Install the fuel pressure regulator vacuum tube to the fuel pressure regulator and the throttle body.
    13. Install the brake booster hose to the throttle body.

    Nov 13, 2010 | Buick LeSabre Cars & Trucks

    1 Answer

    Need to replace intake manifold how do you do this


    Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

    3.8L Engine
    VIN 1 Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Relieve the fuel system pressure.
    3. Drain the cooling system.
    4. Remove or disconnect the following:
      Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
    To install:
    1. Install or connect the following:
      Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.

    VIN K Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Disconnect the negative battery cable.
    3. Drain the cooling system.
    4. Relieve the fuel system pressure.
    5. Remove or disconnect the following:
      Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

      a5adffa.jpg
      Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
    To install:


    140d431.jpg
    Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


    4950e4f.jpg
    Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
    1. Install or connect the following:
      Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.

    Hope this help (remember rated this).

    May 17, 2010 | 2001 Pontiac Bonneville

    1 Answer

    2001 dodge durango engine rpm's are fluctuating up and down. what could be causing this and could this cause the transmission to shift eractically


    Quest#1 Your intake manifold is leaking
    Quest#2 Yes
    Spray carb cleaner while running at intake manifold gasket , both sides, and check for a difference in running condition while spraying to confirm leak here. Replace all intake manifold gaskets and plenum gasket.
    If this does not confirm intake leak , have the Throttle Body cleaned manually by a professional, or yourself using specifically" Throttle Body Cleaner "

    Dec 01, 2009 | 2001 Dodge Durango

    1 Answer

    Instructions on changing the timing cover gasket on a 1991 ford thunderbird with 3.8 liter v6 engine


    first you have to diconnect throttle cable and trans kick down from throttle body. than disconnect wires and vacuum hoses and remove upper intake manifold plenum. that should give you access to valve covers . Remove bolts from covers and change gaskets. also replace the gasket on the upper intake plenum. install items in reverse order of removal. keep track of vacuum lines where the go when you remove . mark with tape their location.

    Nov 08, 2009 | 1991 Ford Thunderbird

    2 Answers

    Vacuum Leak on a 2000 Honda passport


    Replace upper intake gaskets. They are made of metal and plastic. A common problem. Do not remove the very top plenum cover gasket.

    Apr 24, 2009 | 2000 Honda Passport

    1 Answer

    Chevy lumina starts then stalls


    loose connections at coil pack or alternator,fuel not reaching fuel injectors properly,vacuum leak at intake gasket between intake manifold/ plenum and throttle body.

    Apr 04, 2009 | 1996 Chevrolet Lumina Mini

    Not finding what you are looking for?
    2001 Cadillac DeVille Logo

    Related Topics:

    1,226 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cadillac Experts

    yadayada
    yadayada

    Level 3 Expert

    76051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8265 Answers

    Are you a Cadillac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...