Question about 2002 Dodge Dakota Club Cab

1 Answer

I have a 2002 4.7 apart to replace the heads need all torque specs for exhaust manifolds heads intake and timing chain cover

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 8,215 Answers

I think autozone.com has everything you need, with a little navigation. Start here: http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f802d92aa

registration is free and easy

Posted on Sep 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Would like to have torque specs chart please?


Hi there, the following information are for a 2004 Grand Am 2.2L, I hope it helps:

--------------------------------------------------------------------------
Timing Chain, Sprockets, and/or Tensioner Replacement
--------------------------------------------------------------------------
Tighten the chain guide bolts to 10 N·m (89 lb in).
Tighten the chain tensioner bolts to 10 N·m (89 lb in).
Tighten the oil nozzle bolt to 10 N·m (89 lb in).
Timing chain tensioner guide bolt to 10 N·m (89 lb in).
Timing chain bolts to 10 N·m (89 lb in).
Chain guide plug to 90 N·m (66 lb ft).
Timing chain upper guide bolts to 10 N·m (89 lb in).
Timing chain tensioner to 75 N·m (55 lb ft).
Camshaft bolts to 85 N·m (63 lb ft) plus 30 degrees.
-------------------------------------------------------------------------
Intake Manifold Replacement
-------------------------------------------------------------------------
Manifold Nuts and Bolts: 10 N·m (89 lb in).

Aug 30, 2014 | 2004 Pontiac Grand Am

1 Answer

What are the torque specs on a 2002 toyota sienna's spark plugs, air intake manifold, and valve covers? Thank you.


Spark plug torque on the 3.0L engine is 13 ft.lbs. and the 3.3L is 18 ft.lbs.

Valve covers-69 inch lbs.

Intake Manifold-11 ft. lbs.

Jul 07, 2014 | 2002 Toyota Sienna

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

2 Answers

I need the torque specs. for a 2002 Chrysler Sebring conv. I had to replace the engine so I need all of them. Thanks.


What engine size, 2.7L or 3.0L, and torque about what component (cylinder head, intake-exhaust manifold, etc).

May 12, 2011 | 2002 Chrysler Sebring

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

HOW TO FIX A BLOWN HEAD GASKIT?


Buy a gasket kit for the upper end. Remove the valve cover intake and exhaust manifolds. Remove the head bolts. Remove head and clean up block from old gasket material. Take the head to a machinist and make sure that it is not warped. If it is warped either replace the head with a new one or have it machined true. Install new gasket and get torque specs with new head bolts and follow torque sequence using the correct torque specs. Clean exhaust, intake and valve cover of old gaskets. install new gaskets and torque according to specifications.

Nov 27, 2010 | 1993 Jeep Cherokee Country

1 Answer

How to replace a waterpump on a 2001 olds alero 2.4 cam


Water pump is driven by timing chain idler and is mounted on the rear of the timing chain housing. Disconnect the neg. battery cable. Drain cooling system. Disconnect oxygen sensor connector.
Remove upper exhaust manifould heat sheild. Remove exhaust manifold brace. Remove lower exhaust manifold heat sheild. Loosen manifold to exhaust manifold spring loaded nuts. Remove radiator outlet pipe to water pump coverbolts. Disconnect exhaust pipe from manifold.
Pull down on the exhaust pipe to disconnect it from exhaust manifold bolts. Disconnect outlet pipe from oil pan and transaxle. If equipped with manual tranaxle, remove exhaust maifold brace. Leave lower radiator hose attached and pull down on radiator out look pipe to disengauge from water pump. Leave outlet pipe hanging.
Lower vehicle. Remove exhaustmanifold to cylinder head nuts. Remove exhaust manifold to cylinder head nuts. Remove manifould. Remove timing chain front cover. Remove timing chain tensioner. Remove bolts bolts securing water pump cover to cylinder block. Remove water pump to timing chain housing nuts. Remove water pump attaching nuts. Remove water pump and cover assembly. Separate componets as necessary.
WHEN INSTALLING WATER PUMP MAKE SURE YOU FOLLOW THE TIGHTENING SEQUENCES THAT AFFECT SEALING. My frist one I messed up and broke the pump so becarful.
Installation
If cover was separated from body during removal, join this componets with a new gasket and hand tighten bolts. Apply bearing grease to splines of water pump drive. Set body and assemble into position.
Install and hand tighten bolts securing cover to cylinder block. Install and hand tighten bolts securing cover to cylinder block. Installand hand tighten nuts securing body to timing chain housing. Lubracate outlet pipe "O" ring with antifreeze. (I use RTV) Connect outlet pipe. Install and hand tighten bolts. Tighten bolts and nuts to specification in the following sequence. I'll ad the torque spec. at the end but this is where if you tighten out of order something will break.
pump assembly to timing chain housing nuts.
pump cover to pump body bolts
pump cover to cylinder block bolts (Bottom Bolt First)
outlet pipe to cover bolts
To complete installation reverse removel procedure.
Torque specs are 19 in. or 26mm all except water pump cover bolts which are 124 in or 14Nm
I never torque the bolts just make sure there done in the right order.

Oct 19, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

Whats the proper order and torque specs for a 99 32v northstar head?


REMOVAL & INSTALLATION NOTE: The manufacturer recommends that the entire powertrain be removed from the vehicle before removing the cylinder heads.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Powertrain assembly
    • Intake manifold
    • Cam covers
    • Harmonic balancer
    • Timing chain front cover
    • Oil pump
    WARNING
    Align all timing marks before performing the next step.
    • Chain tensioner from the timing chain
    • Cam sprockets
    NOTE: The timing chain remains in the chain case.
    • Timing chain guides, access for the retaining screws is through the plugs at the front of the cylinder head
    • Water crossover
    • Exhaust manifold
    • Cylinder head bolts by reversing the torque sequence
    • Cylinder head and discard the gasket
    WARNING
    With the camshafts remaining in the cylinder head some valves will be open at all times. Do not rest the cylinder head on a flat service with the cylinder face down, or valve damage will result. NOTE: Clean all gasket mating surfaces. Clean the head bolt holes in the crankcase. WARNING
    Be careful when cleaning aluminum gasket surfaces to prevent damage to the sealing surfaces.
  5. Check the cylinder head for warpage; it must be less than 0.002 in. (0.05mm). If the cylinder head was resurfaced, the dimension between the combustion chamber gauge pad and the deck surface must be at least 10.5mm. To install: NOTE: Refer to Section 1 of this manual for the cylinder head torque sequence illustration. The illustration is located after the Torque Specification Chart.
  6. Install or connect the following:
    • New cylinder head gasket
    • Cylinder head, lubricate the bolts with engine oil
  7. Torque the M11 bolts, in sequence, as follows:
    1. Step 1: 22 ft. lbs. (30 Nm).
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 180 degrees).
  8. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  9. Set the camshaft timing
  10. Camshaft guide bolt access hole plugs in the cylinder heads. The plugs should be seated and snug
  11. Install or connect the following:
    • Intake cam covers
    • Oil pump
    • Timing chain front cover
    • Harmonic balancer
    • Cam sprockets
    • Chain tensioner to the timing chain
    • Timing chain guides
    • Intake manifold
    • Water crossover
    • Exhaust manifold. Torque the nuts to 22 ft. lbs. (30 Nm) or the bolts to 18 ft. lbs. (25 Nm).
    • Powertrain assembly
    • Negative battery cable Fig. 1: Minimum head resurface dimension 7922vg04.gif

  12. Fill the cooling system.
  13. Evacuate and charge the air conditioning system.
  14. Run the engine and check for leaks.
prev.gif next.gif

Aug 19, 2010 | 1999 Cadillac DeVille

1 Answer

What is the torque for head screws and timing


300M, Concorde, Intrepid, LHS, 1998-2004 - Cylinder Head
Removal & Installation
2.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    NOTE Place shop rags in the openings to prevent debris from entering the engine.
    Negative battery cable Accessory drive belts Crankshaft damper Intake plenum, lower intake manifold and exhaust manifold Valve and timing chain covers Coolant connections for the cylinder heads
  5. Rotate the crankshaft until the crankshaft timing mark aligns with the timing mark on the oil pump.
    WARNING Be sure the head bolts 9-11 are removed before attempting to remove the cylinder head, the head and/or block may be damaged.
    Primary timing chain Camshaft bearing caps, gradually, in the reverse order of the tightening sequence Camshafts Cylinder head bolts in reverse order of installation starting with bolts 11-9, then 8-1 Cylinder head(s)

To install:


af080a0.jpg

Fig. Camshaft bolt tightening sequence-2.7L engine

eb0ed0f.jpg

Fig. Cylinder head bolt tightening sequence-2.7L engine
  1. Thoroughly clean and dry the mating surfaces of the head and block. Check the cylinder head for cracks, damage or engine coolant leakage. Remove scale, sealing compound and carbon. Clean the oil passages thoroughly.
  2. Place a new head gasket on the cylinder block over the locating dowels.
  3. Inspect the cylinder head bolts for necking (stretching) by holding a straightedge against the threads of each bolt. If all of the threads are not contacting the straightedge, the bolt should be replaced. New head bolts are recommended.
    WARNING Due to the cylinder head bolt torque method used, it is imperative that the bolt threads be inspected for necking (stretching) prior to installation. If the threads are necked down, the bolt should be replaced. Failure to do so may result in parts failure or damage.
  4. Lubricate the bolt threads with clean engine oil, then install them.
  5. Torque the head bolts in the sequence shown in the illustration, utilizing the following steps and tightening values:
    1. Step 1: bolts 1 through 8: 35 ft. lbs. (48 Nm).
    2. Step 2: bolts 1 through 8: 55 ft. lbs. (75 Nm).
    3. Step 3: bolts 1 through 8: 55 ft. lbs. (75 Nm).
    4. Step 4: bolts 1 through 8: plus 90 degree turn using a torque angle meter.
    5. Step 5: bolts 9 through 11: 21 ft. lbs. (28 Nm).

  6. Install or connect the following:
    Camshafts, timing chain and sprockets Water connections to the cylinder head Valve and timing chain covers Crankshaft damper and torque the center bolt to 125 ft. lbs. (170 Nm) Lower intake manifold and intake plenum Exhaust manifolds Accessory drive belts Negative battery cable
  7. Fill the cooling system to the proper level.
  8. Start the vehicle, check for leaks and repair if necessary.
continue...

Apr 11, 2010 | 2002 Dodge Intrepid

3 Answers

Need head bolt, intake manifold, and exhaust torque specs


Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Mar 06, 2010 | GMC Suburban Cars & Trucks

Not finding what you are looking for?
2002 Dodge Dakota Club Cab Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...