Question about 1998 Honda Accord

2 Answers

Where is the mastercylinder? - 1998 Honda Accord

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 67 Answers

Hi the brake master cylinder is located on the brake servo this is where you fill your brake fluid up ur brake fluid bottle is attatched to it .

Posted on Sep 03, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

It is located on your driver side on the fire wall...right where u put brake fluid in....not the canister but behind it...its a big round thing ....hope this helps

Posted on Sep 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 chevy blazer soft brake pedal


The ABS on Blazers are tough to bleed.

Jan 08, 2014 | Cars & Trucks

2 Answers

How do i get the brake piston back so i can fit the new brake pads , to enable me to get them back over the brake disc ?


remove some brake fluid from mastercylinder, then use large c - clamp with the old brake shoe in place tighten c - clamp to push piston back in the bore.put cover back on mastercylinder. be sure to pump brake pedal to seat new brake shoes to the brake rotor.and check brake fluid level in mastercylinder.dont drive car until you get firm solid brakes.

Sep 21, 2011 | Mitsubishi Colt Cars & Trucks

1 Answer

Rear rotor replacement for a 1985 mercadies benz 500 sel


YOU NEED TO SAFELY RAISE SUPPORT REAR OF VECHICLE ON JACKSTANDS. MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. YOU NEED TO SIPHON JUST A LITTLE BRAKE FLUID OUT OF THE MASTERCYLINDER.BECAUSE YOU NEED TO USE LARGE C - CLAMP TO COMPRESS FORCE PISTONS BACK IN THE CALIPER BORES USING LARGE C - CLAMP DOING THIS WILL ALLOW YOU ENOUGH ROOM INSTALL NEW REAR BRAKE PADS.TO REMOVE REAR PADS ONCE YOU COMPRESS PISTON BACK IN THE CYLINDER BORE. YOU CAN TO REMOVE REAR BRAKE PADS BY REMOVING RETAINING PINS IF EQUIPPED OR BRAKE PADS HELD IN PLACE BY RETAINING BOLTS.ONCE YOU HAVE NEW REAR BRAKE PADS INSTALLED.PLACE MASTERCYLINDER COVER BACK ON TOP OF MASTERCYLINDER THEN PUMP BRAKE PEDAL TO SEAT NEW REAR BRAKE PADS AGAINST THE ROTOR UNTIL BRAKE PEDAL FEEL FIRM AND SOLID.THEN RECHECK BRAKE FLUID LEVEL IN BRAKE MASTERCYLINDER ADD LITTLE MORE FLUID IF NEED DONT OVER FILL MASTERCYLINDER.

Sep 11, 2011 | Mercedes-Benz 500-Class Cars & Trucks

1 Answer

Changing the rear brake pads and can't compress the piston into the caliper- any ideas? 2003 rendezvous


FIRST REMOVE SMALL AMOUNT OF BRAKE FLUID FROM THE BRAKE MASTERCYLINDER. THEN USE A LARGE C - CLAMP AND LEAVE THE OLD BRAKE PAD IN PLACE ON PISTON SIDE THEN COMPRESS THE PISTON IN CALIPER BORE. IF YOU SEE SIGNS OF BRAKE FLUID LEAKING AROUND PISTON SEAL.THE BRAKE CALIPER NEED REPLACING.WHEN YOU FINISH BRAKE JOB NEW BRAKE SHOES IN PLACE MAKE SURE BRAKE MASTERCYLINDER COVER BACK ON MASTERCYLINER THEN PUMP BRAKE PEDAL UNTIL NEW BRAKE PADS SEAT AGAINST BRAKE ROTOR.CHECK BRAKE FLUID LEVEL IN MASTERCYLINDER MAKE SURE ITS NOT LOW.

Aug 12, 2011 | 2003 Buick Rendezvous

1 Answer

I am looking for an engine diagram for a 2000 Oldsmobile Alero so that I can locate the master cylinder but I have been unable to find one - can you tell me where to look or where it is located?


LOOK ON DRIVER SIDE.LOOK ON BACK FIREWALL YOU SEE BRAKE POWER BOOSTER UNIT IT LOOKS LIKE BIG METAL BOWL WITH LARGE VACUUM LINE GOING TO IT.THE MASTERCYLINDER CONNECTED TO BIG METAL BOWL LOOKING UNIT.MASTERCYLINDER HAS FOUR SMALL METAL BRAKE LINES TO IT AND IT HAS A SMALL BLACK SCREW CAP ON IT.AND THE CAP WILL SAY BRAKE FLUID.THATS YOUR MASTERCYLINDER.

Jan 29, 2011 | Oldsmobile Alero Cars & Trucks

2 Answers

Need to changer mastercylinder.


Hi,

This is how you go about it;


1) Detach brake line connections from MasterCylinder



2) Detach brake pedal connection to MasterCylinder inside the car


3) Unbolt and remove old MasterCylinder



4) Bench-bleed new MasterCylinder,



5)Do the reverse of steps 1-3





6)Finally, you need to bleed the entire brake system and make sure pedal-height is normal. Honda specifies using a depth gauge to set pedal height



Take care

Sep 03, 2010 | 1997 Honda Accord

1 Answer

1987 Maxima-5 speed is difficult to grt in to gear--How to adjust clutch and check clutch hydraulic fluid?


TO ADJUST PEDAL HEIGHT ADJUST WITH A STOPPER LIMITING THE UPWARD TRAVEL OF THE PEDAL.PEDAL FREE PLAY IS ADJUSTED AT THE MASTERCYLINDER PUSH ROD.IF PUSH ROD IS NON ADJUSTABLE FREE PLAY IS ADJUSTED BY PLACING SHIMS BETWEEN THE MASTERCYLINDER AND THE FIREWALL.ON A FEW MODELS PEDAL FREE PLAY CAN ALSO BE ADJUSTED AT THE OPERATING SLAVE CYLINDER PUSHROD.PUSHRODS ARE AVAILABLE IN THREE LENGTHS FOR THE 310.PEDAL HEIGHT ABOVE FLOOR IS 6.73 - 7.13 INCH PEDAL FREE PLAY IS 0.04 - 0.12 INCH.YOU HAVE CLUTCH FLUID LONG AS YOU SEE BRAKE FLUID IN MASTERCYLINDER.IF MASTERCYLINDER LOW YOU HAVE TO BLEED THE THE CLUTCH MASTERCYLINDER BY LOCATING BLEED SCREW ON SLAVE CYLINDER. REMOVE THE BLEED SCREW DUST CAP.ATTACH A CLEAR TUBE TO THE BLEED SCREW.PUT OTHER END OF CLEAR TUBE IN A CLEAN CONTAINER OF BRAKE FLUID.FILL THE MASTERCYLINDER WITH BRAKE FLUID.OPEN BLEED SCREW 3/4 A TURN.DEPRESS CLUTCH PEDAL QUICKLY.HOLD IT DOWN.HAVE A HELPER TIGHTEN THE BLEED SCREW.ALLOW PEDAL TO RETURN SLOWLY.BLEEDER SCREW TORQUE IS 5 - 6 FT LBS.IF YOU SEE AIR BUBBLES CLEAR BLEED TUBE.REPEAT THE BLEED PROCESS UNTIL YOU SEE NO AIR BUBBLES.DONT LET CLUTCH MASTERCYLINDER GO DRY WHILE BLEEDING.IF SO YOU GOT START BLEEDING PROCESS ALL OVER.HOPE THIS HELP.

Aug 05, 2010 | 1987 Nissan Maxima

1 Answer

Breaks went out 2006 grand caravan. first lost power brakes and pedal was hard to push then went to the floor now goes all the way down and wont build pressure. checked all lines its full of fluid with no...


IT sounds like your brake mastercylinder has went out so what you need to do is get a new mastercylinder and replace that and bleed out the whole brake system after you put on the new mastercylinder.

May 03, 2010 | 2006 Dodge Caravan

1 Answer

Can't find mastercylinder on my 2000 ford focus


on the end of the clutch,and resevoir is from the brake ,follow the thin plastic pipe ?

Dec 06, 2008 | 2000 Ford Focus

Not finding what you are looking for?
1998 Honda Accord Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...