Question about 1984 Chevrolet S-10

Open Question

84 S10 how to remove door panel do I take the window crank off and if so how

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: how to get the window crank off on 2dr 06 cobalt

there is a clip behind the handle. you should see something like a big plastic washer between handle and panel, the clip is between this washer and handle use a pick to get clip off

Posted on Nov 25, 2008

Ad
brandyspoile
  • 61 Answers

SOURCE: how to remove inner window crank on 2006 chev cobalt 2 dr

the handle part of the crank is held on by a small ring, you will need a small flat head screw driver- i used a butter knife, as it works better- push the door panel back just enough you can see behind the round part of the handle, you should be able to see the foot of the clip, push it off, make sure you don't do this in the grass, the ring will roll when it falls off. **please note this is a flat ring and only about the diameter of your little finger**

Posted on Nov 25, 2008

  • 16 Answers

SOURCE: How do I remove the door panel on a 2000 Cavalier?

there is a tool for that, you can get it fairly cheap at most auto parts stores. there is a clip that snaps into the crank. you can do it without the tool. push in on the door panel around the crank handle and look behind the base of the handle. you will see a slot. you should see something silver in that slot. that is the "U" shaped clip. Rotate the handle until you see the ends of that clip. push on the ends of the clip with two flat head screw drivers (or the special tool)and it wil pop off. then you can pull the handle off.

Posted on Jan 14, 2009

  • 75 Answers

SOURCE: remove inside door panel without breaking it

they have push in clips that hold the panel on the door you can pull it off with your hand or go to parts store and buy a door panel removal tool
PLS take time to rate this solution and by the way you will probably need to buy new push in clips to hold panel on

Posted on Feb 17, 2009

  • 10 Answers

SOURCE: how do I remove drivers side door panel on 1998

i think there are screws around the door handle on the in side that need to be taken off the the rest just pop out

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced plugs am wires cap an button on 84 s10 with 2.8 want crank fire in carb


POPPING BACK IN THE CARB IS AN INDICATION OF WIRES CROSSED. PUT THE TIMING MARK ON THE CRANK PULLEY ON ZERO AND REMOVE NUMBER ONE PLUG. FEEL THROUGH THE HOLE IF PISTON IS AT THE TOP. ARE THE ROCKER ARMS ON BOTH VALVES ON NUMBER ONE LOOSE AND UNENGAGED(NEUTRAL). THEN REMOVE THE CAP AND OBSERVE WHICH WIRE THE ROTOR BUTTON IS POINTING TO. IT SHOULD BE POINTING TO NUMBER ONE. THEN ADD THE WIRES IN FIRING ORDER AND TRY TO CRANK AGAIN

Apr 09, 2015 | Cars & Trucks

2 Answers

How do I remove the handle in door panel? I'm trying to remove the door because my window fell off the track, it doesn't have power windows so I have to manually roll them up and down.


1- remove the window crank
2- remove any screws from the door panel; sometimes they are hidden by a plastic cap. look inside the elbow rest cavity; remove any screws you see.
3- insert a flat plastic or wooden tool in the shape of (roughly) a scraper, between the door panel and door and start prying the clips which hold the panel to the sheet metal. get as close to the clips as possible with the tool, as that will be the easiest way. there are about 8 of these clips on an average door. when all the clips have come loose of the sheet metal, lift the panel straight up to remove it. you will find a metal rod attached to the inside of your handle; unfasten it and remove the panel completely. that handle looks like it is part of the panel and cannot be removed separately.

Mar 15, 2013 | Cars & Trucks

1 Answer

How do you remove passenger sliding door handle on oldsmobile silhouitte


The process of removing car door panels is essentially the same for each make of car. You may need to remove these panels when your fixing locks or power windows, replacing window cranks, installing speakers or replacing the side mirrors. Learning how to remove the panels yourself can save money on simple car repairs.
Related Searches:

Difficulty: Moderately EasyInstructionsThings You'll Need
  • Set of screwdrivers
  • L pick
  • Small flashlight
  • Ratchet and socket
    • 1

      Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver.

    • 2

      Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights.

    • 3

      Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out.

    • 4

      Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side.

    • 5

      Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off.

    • 6

      Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together.

    • 7

      Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle.

    • 8

      Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.

Jan 10, 2012 | 1998 Oldsmobile Silhouette

1 Answer

How do you remove a rear door panel on an Audi A3 4 Door


802771-a4_door_card_rear.gif

- Door trim.
Removal
- Unclip decorative panel -2-.
- Remove decorative panel -2- toward front.
- Remove bolts -3- (3x) from door trim -1-.
For vehicles with electric window regulators
- Window regulator switch, removing and installing Page 70-25 .
For vehicles with manual window crank
- Manual window crank, removing and installing Page 70-26 .
For all vehicles
- Unclip door trim -1-. Replace damaged clips Fig. 3
- Raise door trim -1- upward approx. 20 cm. out from door shell.
- Disengage Bowden cable for interior door mechanism Fig. 1 .
- Disconnect electrical harness connectors Fig. 2

Dec 03, 2010 | 2005 Audi A3

1 Answer

How to remove the inside door panel from a dodge 2005 2500 pick up


FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

Need a diagram of how the door panel comes off of a 95 chevy blazer. I need to remove the door panel to fix the lock assembly. Need to know if there are clips at the bottom of the door, or just the screws.


There will always be clips attached to the panel from the inside-after screw removal and window crank removal (window crank on mostly earlier models) You can start at a bottom edge with what i recommend a door panel removal tool-most auto parts store carry these. even if a clip falls out you can reinsert it.Also the door removel tool doubles as a window crank clip remover.

Sep 20, 2009 | 1995 Chevrolet Blazer

1 Answer

Cant get rollup window handle off.


If there is no bolt behind the center of the crank, then there is a u shaped clip holding it on. You will need to push in on the door panel to see it. You should be able to remove it with needle nose pliers, or a pick.

Jun 09, 2009 | 2001 Chevrolet S-10

1 Answer

Avalon door panel


Below are the removal procedures for your vehicle's front inner door panel.


On models without power windows, remove the snap ring retaining window crank handle. Remove crank handle and cover plate.
Remove lower door frame bracket garnish. Using a screwdriver, remove inside door handle bezel. Remove power mirror control switch and disconnect harness connector.
Remove armrest panel. Remove 6 screws. Pry interior door panel loose from door.

May 23, 2009 | 2001 Toyota Avalon

1 Answer

Driver window won't go up; fuse ok; how do i remove door panel


Before you remove the door, check the switch it self. If you have a newer S10 like a 1994 and newer. The window switch panel just popes out from the arm rest with out removing the door panel. Try moving the switch from side to side while pushing the up button and check the wire in the weather boot that runs between the door and body at the hinge.
Good luck and hope this helps.

May 12, 2009 | Chevrolet S 10 Cars & Trucks

1 Answer

I need to know how to replace the door handle for my 1988 s10 pickup


Have to remove the 2 screws in the arm support, slide off, have to remove the hand crank (special tool needed here) and then pull off the door panels with special tool to pry the plastic clips out. Once the panel is off, put the window at its top position and unclip the plastic actuator that holds the rod into place. Undo the 2 selfcutting bolts and replace in the reverse.

Apr 24, 2009 | 1988 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...