Question about 1995 Jeep Cherokee

1 Answer

New starter goodfuses,relaysbattery still no start

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 222 Answers

Check fuel pump 1st, should here it hum for a few seconds when you turn the key to ON (not starting). A bad crankshaft position sensor will cause a no start, yours may have a camshaft sensor as well. ECM needs both to run engine. Does the CEL come on for a few seconds like the other warning lights when you turn the key to ON? If not ECM is dead, shorted out or ground/power is gone to it. Check each spark plug and the wires. If spark is ok on for each plug, fuel pump comes on, I would look at the injectors but usually you get a stall as one goes bad. If those are ok then replace the crankshaft sensor but keep in mind the ECM might be fried.

Posted on Sep 03, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bought new starter, put on now car won't start with key ignition. Started before new starter?? Could starter be bad or solenoid? Can start by touching solenoid & positive in starter

It sounds to me like you have a bad solenoid, If the solenoid was on the starter when you bought it I would go and get another starter. Otherwise just replace the solenoid.

May 02, 2017 | Cars & Trucks

1 Answer

07 ram 5.7 No start 1 click Battery cleaned charged up tried on boost - still 1 click . New starter- ran Jumper wire to starter from battery- 1 click. What can it be ?

If the battery connections at the starter are secure it is likely the solenoid is defective on the new starter.

When attempting to start monitor the battery voltage. If the voltage only changes sightly still above 12 volts it is likely that the starter motor is not getting power. Confirm that the starter solenoid is being powered when attempting to start.

  • all battery connections to the starter are secure
  • and power is applied to the starter solenoid
  • and no crank above 12 volts
these combined conditions will confirm that the new starter is defective.


26375961-eslp3us1ub1u3afrhtff0zvp-3-2.jpg Hope this helps?

Nov 28, 2016 | Cars & Trucks

1 Answer

New battery & starter. Car wont start. Starter clicking.

sounds like solenoid has failed or is sticking

Jan 08, 2015 | 2002 Ford Taurus

2 Answers

I start the car in the morning and drived it had no problem later i tried to start it did not start i tried jumper start it d id not work after 2days i tried to start it start l do not know what is wrong...

Could be battery or more likely it needs a new starter. The starter has nothing to do with care safety. Buy a new starter not rebuilt or junkyard started. Labor for new starter or maybe starter is the same. You might get lucky and rebuilt starter lasts but it doesn't the labor is paid again.

Feb 24, 2018 | 2004 Nissan Maxima

2 Answers

My jeep commander won't start put a new engine new starter every thing new and it won't start

You say "it won't start".
Does the Starter turn over and the engine not start?
or Starter not tun over.

Apr 03, 2014 | 2006 Jeep Commander

1 Answer

Car wont start has charged battery lights and radio come on new starter. drainging battery even though the battery is fully charged its reading its not tempature gauge reading hot but its not runn

If the problem began when (or soon after) installing the new starter, start checking there. Ensure that all cables to the starter are tight. As a second possibility, if the new starter was actually a rebuilt replacement, the solenoid could be faulty. (I went through three rebuilt starters on my son's truck until we got one that worked properly.)

Mar 06, 2014 | 2004 Ford Mustang GT

1 Answer

My 87 jeep starter stays ingaged when I try to start it

needs shimmed or the bendix is bad in the starter and not allowing to release. most likely just needs shimmed if it's a new starter, however you can get a bad starter (new or rebuilt)

Aug 28, 2012 | 1987 Jeep Cherokee

1 Answer

Starter drags???

it sounds like the new starter is faulty , I would suggest having it checked by a service shop or a starter rebuild shop, most parts supply stores dont charge for this test but you will have to remove the starter from the truck.

Feb 09, 2009 | 1986 Ford F 250

Not finding what you are looking for?
1995 Jeep Cherokee Logo

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides