Question about 1999 Cadillac DeVille

1 Answer

I want to know how change my oil pan gasket. - 1999 Cadillac DeVille

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,190 Answers

The oil pan gasket is a complex task. Due to the design of the Northstar engine,ie the exhaust crossunder exhaust pipe either the engine has to be removed from the car or remove the transmission.... The oil pan is a two piece assembly. Upper and lower. Yhank you

Posted on Sep 03, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: Oil Pan Gasket

yes i have and its a nitemare ,dares one bolt u can not get at becauce its under the drive train in the corner of the sump .to take out sump you have to take out drive train u will no what i am talking about if u have started the job..good luck to u mate..

Posted on Oct 09, 2008

  • 3 Answers

SOURCE: To change the oil pan gasket in a 93 Tercel

is not hard, i changed mine 95 tercel

Posted on Oct 24, 2008

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 10 Answers

SOURCE: Is there ANY way to change the oil pan gasket on a S10...

Remove motor mount bolts and rear transmission crossmember bolts or nuts,suppport engine/trans. see if u have enough clearance between pan and axle remove pan. if not, split the exh away from the manifolds. worth a try

Posted on Dec 22, 2009

  • 4 Answers

SOURCE: changing oil pan gasket on 02 impala ls 3.8

The engine does have to be raised. The bolts are not easy to get to until the engine is lifted and the engine mount is removed. I'm doing this job right now and the book time is around 5 hours.

Posted on Jan 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

HOW DO I CHANGE OIL PAN GASKET IN A 1997 ACURA TL


Drain the oil, Remove the bolts/screws holding the pan onto the bottom of the engine. Remove all traces of old gasket. Clean the mating surfaces. Use bearing grease to stick the gasket onto the engine. Replace the pan and all bolts.

Nov 14, 2014 | Cars & Trucks

1 Answer

How hard is it to change a oil pan gasket


It's not hard ,but you need to know if there might be any obstruction that might get in the way preventing you dropping the pan down just make sure all the oil is drained before you start ,and make sure you clean both surfaces thoroughly before putting gasket on ,and you must tighten all bolts or screws evenly or it will leak .

Aug 28, 2012 | 1999 Pontiac Sunfire

1 Answer

What guru said is correct, this is also what the last oil change place told me. Unfortunately they couldnt do the oil change as the oil pan plug, gasket, oil drain and the oil pan itself needs to be...


Ebay has several junkyards that deal in newer wrecked cars and sell for 1/2 of new price. Do a search for your vehicle, if nothing is listed, contact the seller. Watch their ratings! Most are very good but some take forever to ship out.

Feb 13, 2011 | 2004 Mitsubishi Endeavor

1 Answer

Change oil pan gasket


YOUR OIL PAN GASKET IS ATTACH TO TOP OF OIL PAN.WHICH SEAL TO ENGINE BLOCK.YOU NEED A HAYNES REPAIR BECAUSE YOU HAVE TO REMOVE RIGHT MANY THINGS TO GET OIL PAN OFF TO GET TO GASKET.

Feb 23, 2010 | 1999 Oldsmobile Alero

2 Answers

How do you change oil pan gasket


have car jacked up and blocked for safety,drain oil from engine and remove the oil pan bolts,remove pan.

Nov 23, 2009 | 1996 Honda Accord

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

2 Answers

Oil Pan Gasket Leak


have the engine cleaned of all oil then recheck, an oil pan gasket doesn't leak in a manner you are discribing.

Sep 01, 2009 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Changing oil pan gasket on 1989 Ford Aerostar


drain the oil from the pan and remove the filter.
Lift the car up and secure it . So it will not roll or fall. Remove the bolts from the pan using a 10 mm or so and a rachet and small extension. There are several bolts all around the pan. Remove the pan and remove the gasket. Clean up the pan and remove all gasket material from the pan. Install the new gasket around the pan and replace back.

Apr 05, 2009 | 1989 Ford Aerostar Cargo

Not finding what you are looking for?
1999 Cadillac DeVille Logo

442 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...