Question about 1994 Acura Integra

1 Answer

Im trying on chaiging my fuel filter , i took it of the mount braket , but the bolts in the fillter seem not to come off, and im working in acura integra 94'

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Put it back on the mounting bracket and try loosening it then

Posted on Sep 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626


This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

1 Answer

Best way to take it off


Acura Coupes and Sedans 1986-1993 Repair Guide
Fuel Filter

Print
The recommended change interval for the fuel filter on all models is 60,000 miles under normal service. Severe service will require more frequent changing of the fuel filter.
The filter is located in the passengers side of the engine compartment.

CAUTION Before disconnecting any fuel lines, be sure to open the gas tank filler cap to relieve any pressure in the system and wrap a shop towel around the fuel line fitting before opening. Observe all fuel handling precautions.


REMOVAL & INSTALLATION

See Figures 1, 2 and 3

  1. Disconnect the negative battery cable.
  2. Wrap a shop towel around the fittings and using a proper wrench, slowly loosen the fuel line fittings.
  3. Remove the 2 banjo bolts from the fuel lines.
  4. Remove the fuel filter clamp retaining bolt and the clamp.
  5. Remove the filter from the vehicle.

It is very important that ALL of the fuel line banjo bolt washers be replaced every time the banjo bolts are loosened. If the washers are not replaced the fuel lines will leak pressurized fuel causing the risk of fire or explosion.
  1. Install the new filter in position and tighten the clamp mounting bolt to 7 ft. lbs. (10 Nm).
  2. Attach the banjo fittings with new washers in place. On Legend and Vigor, tighten the fuel line flare connector to 28 ft. lbs. (38 Nm). On the remaining models, tighten the banjo fitting bolts to 20 ft. lbs. (27 Nm).
  3. Start the vehicle and check for leaks.



0900c152800494d0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Disconnecting the fuel lines from the fuel filter


0900c152800494d1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Fuel filter replacement-1991-93 Integra


0900c152800494d2.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Fuel filter replacement-Legend and Vigor

Jul 08, 2012 | 1991 Acura Legend

1 Answer

How to replace cabin and fuel filters for 1996 acura 3.2 TL?


For the fuel filter:


Removal & Installation

Many Acura models are equipped with a theft deterrent audio system. Make sure you have the necessary code before disconnecting the battery.

  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure, as outlined in Section 5 of this manual.

On 2.2L and 3.0L engines you may have to remove the engine wire harness bracket and power steering feed hose clamp.

  1. Wrap a shop towel around the fittings and, using a proper flare nut wrench, slowly loosen the fuel line fittings.


c17hydro_144.gif
  1. Remove the banjo bolts from the fuel lines.
  2. Remove the fuel filter clamp retaining bolt and the clamp.
  3. Remove the filter from the vehicle.

A through cleaning of the high pressure hoses is recommended before installation.

To install:

  1. Install the new filter and tighten the clamp mounting bolt to 7 ft. lbs. (10 Nm).
  2. Attach the banjo fittings with new washers in place.
  3. Tighten the banjo fitting bolts to 25 ft. lbs. (33 Nm).

On 2.2L and 3.0L engines you may have to reconnect the engine wire harness bracket and power steering feed hose clamp.

  1. Connect the negative battery cable, then start the engine and thoroughly check for leaks.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 35; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Jan 23, 2011 | 1996 Acura TL Series

1 Answer

Where to find the fuel filter and how to replace it


The filter is located under the vehicle on the left frame rail near the front of fuel tank.

You must remove the bolt securing the fuel filter bracket strap. Use a fuel line quick release tool (available at any comercial parts store) to disconnect the fuel lines from the filter. Remove the filter.

To install, simply click the fuel lines onto the new filter and install the filter into the braket and secure with the bolt.

Dec 27, 2010 | 1996 Jeep Grand Cherokee

2 Answers

How to put a fuel filter on a hond accord


The fuel filter is located on the left rear of the engine compartment under the brake booster area. The lines unscrew from the filter and the braket holding the filter has a bolt that can be loosened to get the filter out. The filter will not come out of the bracket until the lines are disconnected. They can be very hard to get to. The lines are usually very tight and sometimes corroded. I am an experienced technician and have a lot of trouble with Honda fuel filters...Good luck!

Dec 19, 2010 | 1996 Honda Accord

2 Answers

How to change fuel fillter


2002 Hyundai Sonata 2.4L MFI DOHC 4cyl the Fuel Filter is located uUnder vehicle, driver side, below seating area, driver side of fuel tank, mounted on frame in fuel line.


Hyundai Car 1999-05 - Removal & Installation

NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

d8227e1.jpg

Fig. Remove the fuel filter
  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.

Hope this help to solve your problem.

Apr 24, 2010 | Hyundai Motor 2002 Sonata

1 Answer

Alternater mounting braket diagram


try fitting the bracket alone using the bracket bolt as your guide, check the position of your alternator, alternator pulley must be on line with your its belt...

Apr 14, 2010 | Oldsmobile Cutlass Supreme Cars & Trucks

3 Answers

IT turns over but when i press the gas pedal it wont do anything. Like **** not getting gas


Fuel pump is the most likely fault here, it is in the gas tank on most cars but a few on mounted to the frame.....

Feb 21, 2010 | 1995 Ford Escort

1 Answer

When idling my 2003 Acura TL the engine seems to want to almost die, also when i got on the freeway it seem to pull hard and **** like it was having trouble shifting into 5th gear. It also seems to run...


You may need to change the coil pack(s) or modular. The modular is what the coil pack(s) mount to. I'm not familiar with that engine so you may have a 3 piece coil pack, or a 1 piece. (If it doesn't have a distributor). You may first try replacing the coil wire. There is a good chance that is loose, or bad. It could also be the coil itself. Try the coil wire and if it still acts up, then try the others. Also, when you changed the plugs, did you put new plug wires? When I do a tune up on my vehicles, I change the plugs, wires, distributor cap and rotor, (coil pack,modular), whichever is equipped, oil, oil filter, tranny fluid and filter with gasket, valve cover gaskets, oil pan gasket oil filter, and fuel filter. Try changing the fuel filter as well, as plugged or dirty fuel filters can cause stall outs. I hope this information helps. Thank you for choosing fixya.com for answers.

Apr 01, 2009 | 2000 Acura TL

2 Answers

1991 Ford F 350 Dual rear-end


To willmc8608
From shadow@richlandms.com

If the Therostat housing is mounted on the left front of the engine, unbolt the alternator and it's mounting, then unbolt the vaccum booster pump, this will reveal the mounting bracket to the fuel filter assembly mounting braket, unbolt the supports to the assembly and move to the side. Two bolts hold the therostat inlet ini place.

Jun 08, 2008 | 1991 Ford F350

Not finding what you are looking for?
1994 Acura Integra Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...