Question about 1990 Honda Civic

1 Answer

What socket do i need to remove the rear spindle nut on a 1990 honda civic

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

I believe its a 32mm or a 36....but im more to 32mm..... hope this helps

Posted on Sep 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Axle nut size


measure across the flats of the nut and that will be the size of the socket. Use an adjuster spanner and measure the opening== example if it is 30 mm across the flats then it will be a 30 mm socket

Apr 19, 2014 | 1990 Honda Accord

1 Answer

How to change back hub on 97 cr-v


Rear Brake Discs
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-1.1-800x800.jpg Replace the bearing and race as a single set. automotive roller bearing. image by Tom Oliveira from Fotolia.com

    Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.

    If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.

    At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WDRoqv Rear Brake Drums
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-2.1-800x800.jpg Pack the bearing with bearing grease before installation. roller bearing image by Tom Oliveira from Fotolia.com

    If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.

    You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.

    Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.

    Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WN9eBb

Aug 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

I need help replacing a right upper control arm on my 98 civic si


jack up vehicle ,remove tire/wheel,separate upper ball joint from steering spindle. next open hood, look at the right front strut mount. there is a nut on each side of the strut mount, these nuts hold the upper control arm to the vehicle. remove the nuts and pull the control arm out. install in reverse procedure. NOTE: need to have alignment checked after replacement.

Aug 14, 2011 | 1998 Honda Civic

2 Answers

Pulling an alternator


Removing the rear-mounted alternator on early 1990s Civics and CRX can be frustrating. After removing the upper adjusting bracket bolt and the lower pivot bolt, the alternator can *almost* come out the top and almost fits behind the intake manifold.

The only easy exit path is out the left wheel well. Side access requires removing the wheel and unfastening three of the plastic retainers holding the upper end of the splash guard. But even this doesn't provide quite enough room. You need to tuck the alternator back under the intake, unbolt the lower alternator bracket (two bolts, 14mm socket) before the alternator can be removed.

The tools needed:

10mm socket -- alternator power connection, battery terminal
12mm wrench -- adjusting bracket
14mm socket -- adjusting bracket, pivot bolt, alternator bracket

Mar 30, 2010 | 1991 Honda Civic

1 Answer

How do i remove a front axle spindle nut off my 2001 honda civic lx


Unstake the nut and turn left, a impact wrench is needed, be sure to torque the nut when putting it back together, 135 ft lbs.

Feb 05, 2010 | 2001 Honda Civic

1 Answer

I have 1990 honda civic it has good compresson


Remove valve cover, loosen valve and lifter nuts, remove rod and seal.

You can go to autozone.com and register for full free online repair manual with everything you could need.

Sep 16, 2009 | 1990 Honda Civic

1 Answer

I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic


Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

May 23, 2009 | 1994 Honda Civic

2 Answers

How do i remove the rotor for a 1990 honda accord


remove caliper, caliper bracket it may or may not have a screw that holds it to the hub pretty easy actually

hope2help

Apr 05, 2009 | 1990 Honda Accord

1 Answer

Take out a 95 honda civic EX coupe engine


Remove the large nut on the end of the axle. Remove the outer tie rod end. Remove the upper spindle mount. There is a cover over the bolt. Remove the brake caliper and the lower ball joint and disconnect speed sensor if equipped. Remove spindle and pull the axle out. You may need a large flat head screw driver to pop the sxle out of the transaxle.

Jun 14, 2008 | 1995 Honda Civic

Not finding what you are looking for?
1990 Honda Civic Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...