Question about 1999 Pontiac Grand Prix

1 Answer

I have a 99 grand prix gtp and i connect the lower ball joint to the a frame helpppp

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 8,172 Answers

Need 2 people for this job. Make sure car is not jacked under A-Frame. Bring hub in to connect axle on splines. Next, one person uses a long prybar to pry the A-frame down (stick pry bar in from back and under inner fender well or frame. Other person rotates the hub inward, fully seating the axle and slipping the ball joint into the A-Frame. Other person can now stop prying, as joint should stay together.

Posted on Sep 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission Compatibility


As you see I provided you the models you can apply the transmission :The 4T65E-HD (code MN7) is a heavy duty version of the 4T65-E used with more powerful engines such as the LS4 V8 and L67/L32 supercharged V6. Applications: 2.93:1 MN7 Pontiac Bonneville SSEi L67 Chevrolet Impala L67 Chevrolet Monte Carlo L67 Pontiac Grand Prix GTP/GXP Buick Regal GS Buick Riviera L67 (97-99) So ,yes you can!

May 28, 2013 | 1998 Pontiac Grand Prix

1 Answer

How to repair a lower ball joint on the passenger side


Hi.


jshreader_9.jpgjshreader_8.jpg

1. Raise and support vehicle.
2. Remove tire and wheel assembly, then install modified outer seal protector No. J34754, or equivalent, Fig.3 .
3. Remove lower ball joint cotter pin and nut, then loosen ball joint from steering knuckle using tool No. J-29330, or equivalent.
4. Position a suitable pry bar between suspension support and lower control arm and separate lower ball joint from steering knuckle. On some models, it may be necessary to remove nut attaching link to stabilizer shaft.
5. Locate center of rivet body and mark with a center punch.
6. Using a 1/8 inch drill, drill pilot holes completely through rivets. Using a 1/2 inch drill, drill final holes through rivets to ensure fitting of new ball joint.
7. Remove ball joint from lower control arm.
8. Assemble new ball joint to lower control arm with bolts provided in service package, Fig.9 . Tighten bolts to specifications.
9. Insert ball joint stud into steering knuckle and tighten nut to specifications, then install cotter pin.
10. Install wheel and tire and check front wheel alignment.

I hope this helps you.

Thanks.

Nov 28, 2010 | 1994 Pontiac Grand Prix

1 Answer

How to replace a lower ball joint on a 1988 pontiac grand prix hit a pothole and it popped out


Hope this helps and please don't forget to rate! Thank you!


e8fbd9d.gif
Front ball joint with heat shield

Remove and Replace-

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the front wheel and tire assembly.
  4. Unfasten the retaining bolts, then remove the ball joint heat shield.
  5. Remove and discard the lower ball joint cotter pin.
  6. Remove the ball joint nut.
  7. Loosen, but do NOT remove, the stabilizer shaft bushing assembly bolts.
  8. Separate the ball joint from the strut/knuckle assembly using ball joint/tie rod puller J-35917 or equivalent.
Do NOT damage the halfshaft boots when drilling out the ball joint rivets.
  1. Drill out the rivets retaining the ball joint to the knuckle strut assembly and remove the ball joint from the knuckle. Use a 1/8 in. drill bit. Refer to the instructions in the ball joint replacement kit.
To install:
  1. Position the lower ball joint in the strut/knuckle assembly.
  2. Install the four ball joint bolts and nuts, as shown in the ball joint kit and tighten to specifications.
  3. Install the ball joint-to-lower control arm. Install a new ball joint-to-lower control arm nut.
  4. Tighten the stabilizer shaft bolts to 35 ft. lbs. (48 Nm).
  5. For 1988-91 vehicles, tighten the ball joint-to-lower control arm nut 15 ft. lbs. (20 Nm) plus at least an additional 90° (11/2flats), plus enough to align the cotter pin hole. Do NOT overtighten.
  6. For 1992-96 vehicles, tighten the lower ball joint nut to 63 ft. lbs. (85 Nm). Tighten to align the next slot in the nut with the cotter pin hole in the stud. Do NOT tighten more than 60° (1 flat) to align with the hole.
  7. Install a new cotter pin.
  8. Position the ball joint heat shield and secure with the retaining bolts. Tighten to 62 inch lbs. (7 Nm).
  9. Install the front wheel and tire assembly, then carefully lower the vehicle.
  10. Connect the negative battery cable and check for proper suspension operation

Apr 26, 2010 | 1988 Pontiac Grand Prix

1 Answer

What is the easiest way to pull trasnmission out of 99 Grand Prix GTP


hi there is no easy way to pull the transmission
if you don't have a hoist i would advise you not to try
you have to take the sub frame out(craddle)
if you do not have the right tools and equipment the engine will fall on the ground when u remove the frame
sorry for the bad news

Nov 05, 2009 | 1999 Pontiac Grand Prix

1 Answer

How do you replace a headlight switch in a grand prix


how do you replace a headlight switch in a 07 grand prix gtp. head lights do not come on. all other lights work. fuses are good. amd so are the bulbs. was told that the headlights themselves were not getting a charge. and was told that it was the headlight switch.

Oct 02, 2009 | 1999 Pontiac Grand Prix

2 Answers

Ball Joint connecting lower control arm and spindle 99 Grand Prix


put a jack stand under the ball joint lower car, this applies pressure on the ball joint so the shaft of the ball joint does not turn.
heat the nut as well.

May 12, 2009 | 1999 Pontiac Grand Prix

1 Answer

1998 pontiac gtp ,


remove the right side wheel
seperate the ball joint
you may have to remove the stablizer bar link
remove the drive axle nut 32mm or 1 5/16
slide the front of the axle back through the hub bearing
then pop the axle out of the transmission
then install your new axle and reassemble

Jul 17, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
1999 Pontiac Grand Prix Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...