Question about 1996 Isuzu Rodeo

1 Answer

1996 izusu rodeo 3.2 I need to remove the crankshaft pulley bolt

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 8,522 Answers

First remove starter, then use pry or large screwdriver to hold flexplate from rotating while someone else loosens the pulley bolt.

Posted on Sep 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many foot pounds of torque should i tighten the bolt that holds on the harmonic balance on a 1996 subaru legacy outback


From FSM:

B: INSTALLATION
1) Install the crankshaft pulley.
2) Install the pulley bolt.
To lock the crankshaft, use ST.
ST 499977400 CRANKSHAFT PULLEY
WRENCH
(1) Clean the crankshaft pulley thread using an
air gun.
(2) Apply engine oil to the crankshaft pulley bolt
seat and thread.
(3) Tighten the bolts temporarily with tightening
torque of 44 N·m (4.5 kgf-m, 33 ft-lb).
(4) Tighten the crankshaft pulley bolts.
Tightening torque:
127 N·m (13 kgf-m, 94.0 ft-lb)

Apr 10, 2014 | 1998 Subaru Legacy

1 Answer

Install water pump


you need a bolt type puller to remove crankshaft pulley go to auto parts store ask salesperson for bolt type puller used to remove crankshaft pulley harmonic balancer.

Dec 07, 2011 | 1997 Isuzu Rodeo

1 Answer

Do i need to remove camshaft bolt to remove camshaft pulley on 1996 Mazda Protege


1 Locate the crankshaft pulley on your vehicle. This is usually on the driver's side, but may be on the passenger's side if your timing belt is located on the passenger's side. Place the end of the tire wrench over the lug nuts of the appropriate wheel of your vehicle and turn the wrench about 45 degrees. 2 Put your emergency brake on. Then use the floor jack to jack up the vehicle's front jack point (an extension of the frame).3 Put the jack stands under the frame of the vehicle. Then, lower the vehicle onto the jack stands. 4 Continue to loosen and remove the lug nuts, and pull the wheel off.5 Remove the plastic rivets that hold the splash guard in place in the wheel well. To do this, you need to wedge the screwdriver in between the rivets and the splash guard and pry them out.6 Locate the crankshaft pulley. It will be right behind the splash guard you just removed.7 Remove the crankshaft bolt using the crankshaft bolt remover tool. Place the tool over the crank pulley bolt in the center of the pulley. This device prevents the pulley from rotating while you loosen the bolt.8 Place the socket end of the impact wrench over the crankshaft bolt remover tool. Set the impact rench to turn counterclockwise and turn on your air compressor. Wait until the compressor is fully charged. Then, work the bolt loose. It may take a while as this bolt normally requires in excess of 800 ft lbs of torque to remove.9 Attach the arms of the crankshaft pulley removal tool over the pulley and tighten the tool to the pulley using the tool's supplied bolts. Continue to tighten the tool using the bolts until the crankshaft pulley is pulled off the crankshaft.

Oct 03, 2011 | 1996 Mazda Protege

1 Answer

I am replacing the water pump on my 1996 Isuzu Rodeo. One of the water pump bolts is under the lower timing belt cover. However, the lower timing belt cover appears to connect around the crank shaft...


Hello Ralph,

What you actually going to have to do is take both timings covers off eventually. The waterpump is driven by the timing belt, and will have to be removed along with various other components.

The pulley bolted to the crankshaft will have to be removed, as well as the entire fan assembly. I forget what the socket is I used on it, but I believe it was 1-1/8".

If you send me an email to sernst@insightbb.com, I'd be more than happy to send you a .pdf file that details what you are getting into. Too long to list on here.

Best regards,
Steve

May 21, 2011 | 1996 Isuzu Rodeo

1 Answer

We need the sequence for a Head bolt torque on a 1996 Izusu Rodeo


For the V6 3.2L engine it is 6 - 2 - 3 - 7 on top, and 5 - 1 - 4- 8 on the bottom. These are M11x1.5 bolts and should be torqued to 47lb-ft.These bolts should not be re-used, only replaced.

The three M8x1.25 bolts on the left end are sequence numbers 11 - 10 - 9 from top to bottom and should be torqued to 15lb-ft.

Reference model 1997 Rodeo

Feb 22, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Which way do u turn the harmonic balancer bolt to remove it


gas engine :counter clock wise use penetrating oil let soak lefty loosey Diesel Engines

The 2.2L diesel engine utilizes an exposed crankshaft pulley and a hidden crankshaft timing pulley/damper. The following procedure may be used to remove the exposed crankshaft pulley.

  1. Disconnect the negative battery cable.

  2. Loosen and remove the accessory drive belts.

  3. Turn the crankshaft pulley to align the timing mark with the engine pointer. This should be done if any further procedures are being performed which might disturb valve timing.

  4. Remove the retaining bolts, then remove the crankshaft pulley.

To install:

  1. Align and install the crankshaft pulley.

  2. Install the retaining bolts, then tighten to 10-17 ft. lbs. (14-23 Nm).

  3. Install the accessory drive belts, then properly adjust their tension.

  4. Connect the negative battery cable.

Dec 12, 2010 | 1994 Isuzu Rodeo

1 Answer

Hi ive got a 1996 isuzu bighorn ive attempted to change the timing belt but the injector pump pulley moved when i took the belt off. i put it back where i thort it was and tried a tooth either way but no...


Timing belt installation

1. Ensure locking bolts located correctly [4] & [5] in the picture below:

tdisline_32.jpg
CS = Crankshaft
CA = Camshaft
IP = Injection Pump

2. Ensure timing marks aligned [10].
3. Fit timing belt in clockwise direction, starting at crankshaft sprocket.

NOTE: "ISUZU" lettering on belt should be readable from front of engine.

4. Slacken tensioner pulley bolt [9]. Push tensioner pulley against belt.
5. Ensure belt is taut between injection pump sprocket and tensioner pulley as well as crankshaft sprocket and camshaft sprocket.
6. Position tensioner lever [8] against tensioner pulley housing.
7. Remove locking bolts from sprockets [4] & [5].
8. Apply a load of 10 ... 12 kg to tensioner lever. Use spring balance [11].
9. Tighten tensioner pulley bolt to 80 Nm.
10. Turn crankshaft slowly 45 degrees anti-clockwise. Use spring balance to tension belt.
11. Repeat tensioning procedure at 45 degrees intervals for one anti-clockwise turn of the crankshaft.

NOTE: DO NOT turn crankshaft clockwise during tensioning procedure!

12. Fit tensioner lever to original position. Tighten nuts [12].
13. Install: Injection Pump flange [6], Camshaft sprocket flange [7], and water pump pulley.
14. Install components in reverse order of removal & refill coolant.

tdisline_33.jpg
PLEASE DO RATE MY RESPONSE. THANKS!

Nov 27, 2010 | 1996 Isuzu Trooper

1 Answer

Where is the oil pump located on a 2003 isuzu rodeo sport 4 cyl.?


Timing Cover Assembly



Oil Pump
Removal
  1. Disconnect battery ground cable.
  2. Drain engine oil.
  3. Remove crankcase assembly.
  4. Remove crankshaft pulley.
  5. Remove timing belt.
  6. Remove timing pulley from crankshaft.
  7. Remove four fixing bolts from oil filter assembly.
  8. Remove oil strainer fixing bolts, remove oil strainer assembly with O-ring.
  9. Remove three bolts from oil pipe and O-ring.
  10. Remove eight oil pump fixing bolts, then oil pump assembly.
  11. Remove sealant from mounting surface of oil pump assembly, cylinder block and take care not to damage mounting surfaces of oil pump and cylinder block.

Jun 04, 2010 | 2003 Isuzu Rodeo

1 Answer

Would like information on timing belt settings on a 1993 Isuzu Rodeo 4X4 3.2 We have already bought the book. It seems that the setting still are not what this particular motor/engine needs are there other...


look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)


  1. Pusher
    • Tighten bolt to the specified torque.
Torque 19 N-m (19 lb-ft)


  1. Timing belt cover
    • Remove crankshaft pulley that was installed in step 9.
    • Tighten bolts to the specified torque.
Torque 17 N-m (12 lb-ft)


  1. Oil cooler hose
    • Tighten oil cooler hose bracket bolts to the specified torque.
Torque 22 N-m (16 lb-ft)


  1. Crankshaft pulley assembly
    • Using special tool J-8614-01, hold the crankshaft pulley.
    • Tighten center bolt to the specified torque.
Torque 167 N-m (123 lb-ft)


  1. Crankshaft pulley; P/S belt
    • Tighten fixing bolt to the specified torque.
Install the belt on the idler pulley.

Mar 07, 2010 | 1993 Isuzu Rodeo

1 Answer

Remove bolt front of crankshaft


Get a half inch breaker bar with socket on the bolt, lean it all the way to the right, put the handle up against something solid and hit the starter button one klik, should do it. Don't laugh, that is what the book says. It works, I've done it 3 times on my 2, 94 rodeos.

Jun 08, 2009 | 1994 Isuzu Pickup

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

Related Topics:

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14380 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...