Question about 1991 Toyota Cressida

1 Answer

Trying to replace starter on 1991 toyota cressida and having trouble reaching the upper bolt

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

Extensions, and a swivel is the easiest way. Otherwise, disconnect the motor mount, and pull the engine forward.

Posted on Sep 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump located


e74a0ebc-de67-478a-8aef-a52d66b71ca1.jpgThis is take from my 1991 toyota cressida repair manual send me you email through 0432401052 and ill send you next page hope this helps

Jun 16, 2014 | 1991 Toyota Cressida

1 Answer

How to replace front strut insert of toyota cressida model 91


Im not sure what car the instructions above are for, but it's not a Cressida. They dont have upper front control arms.

Anyways,

You remove the brake line, brake caliper, brake rotor. Then you remove the sway bar end link that attaches to the shock housing. Next remove the lower 2 shock bolts and the 3 upper mount bolts in the engine bay. Then you push down on the lower control arm so that you can remove the entire shock/spindle assembly.

Then take it to a shop to compress the spring to take it all apart.

Apr 04, 2012 | Toyota Cars & Trucks

1 Answer

Does a 1991 toyota cressida have a timing belt or a timing chain? If it is a timing belt, how often does it need to be changed? If it is a timing chain does it need to be replaced at all?


On 1997 & prior models, the timing BELT interval for vehicles operated under conditions of excessive idling & or low speed driving for long distances, replace at 60,000 mile intervals.

Nov 30, 2010 | 1991 Toyota Cressida

1 Answer

How do I replace the front right turn signal light on a 1991 Toyota Cressida?


open the hood and look where the turn signal is located and there should be a clip holding the baulb in place

Nov 10, 2010 | 1991 Toyota Cressida

1 Answer

Starter replacement - 1991 Toyota previa


Here are detailed, step-by-step instructions for the removal and re-installation of your starter motor. Hope this helps! Have a great day!

Starter Toyota Previa 1991-1997 Repair InformationREMOVAL & INSTALLATION
See Figures 5 through 12
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front driveshaft.
  4. Remove the nut and disconnect the starter wire.
0900c15280089fbb.jpgFig. 5: Disengage the starter wiring
  1. Disconnect the starter connector.
0900c15280089fbc.jpgFig. 6: Remove the cap hiding the nut 0900c15280089fbd.jpgFig. 7: It will be necessary to use an extension to remove the nut
  1. Remove the bolt holding the starter stay to the upper stiffener plate.
  2. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  3. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
0900c15280089fbe.jpgFig. 8: Four bolts hold the starter in place 0900c15280089fbf.jpgFig. 9: The nut is located on the top of the starter 0900c15280089fc0.jpgFig. 10: Extract the starter from the engineTo install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc1.jpgFig. 11: Bolt locations on the 2WD models
  1. If equipped with 2WD, install the starter, nut and three bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc2.jpgFig. 12: Bolt locations on the 4WD models
  1. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  2. Install the starter connector.
  3. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  4. If equipped with 4WD, install the front driveshaft.
  5. Connect the negative battery cable.
SOLENOID REPLACEMENT
The starter solenoid (magnetic switch) is an integral part of the starter assembly.
  1. Remove the starter from the van. Remove the heat insulator from the starter assembly, if equipped.
  2. Disconnect the wire lead from the magnetic switch terminal.
  3. Remove the two long, through bolts holding the field frame to the magnetic switch. Pull out the field frame with the armature from the magnetic switch.
  4. Toseparate the starter housing from the magnetic switch assembly, remove the two screws and the starter housing with the pinion gear (1.6 kW), idler and clutch assembly.
To install:
  1. If necessary, install the gears and clutch assembly to the starter housing. Apply grease to the gear and clutch assemblies and place the clutch assembly, idler gear, bearing and pinion gear (1.6 kW) in the starter housing.
  2. Insert the spring into the clutch shaft hole and place the starter housing onto the magnetic switch. Install the two screws.
  3. Install the field frame with the armature onto the magnetic switch assembly and install the two through bolts. Tighten the bolts on the 1.4 kW to 52 inch lbs. (6 Nm) and on the 1.6 kW to 82 inch lbs. (9 Nm).
There is a protrusion or tab on each part; make sure you line them up correctly during assembly.
  1. Connect the wire to the terminal on the magnetic switch and tighten the nut to 52 inch lbs. (6 Nm). Install the heat insulator, if equipped.
  2. Reinstall the starter on the vehicle. Check starter system for proper operation.

Nov 23, 2008 | 1991 Toyota Previa

2 Answers

86 toyota cressida. how to remove the upper starter bolt since there is NO clearance for any sockets or your hands?


Holy hell these engines are tight. I had the same prob with my 88. Finally figured it out with about a good foot and a half of ratchet extensions. It'll help if they have wobbles on the end. You'll have to guide the socket by feel (cause you can't see the bolt, but once you're on it the extentions should get your ratchet in a spot where you can give it a good 1/4 turn

best of luck!

Jul 23, 2008 | 1988 Toyota Cressida

1 Answer

Where is the oil pressure switch on a 1991 6 cyl toyota cressida?


Oil Pressure Switch On your 1991 Toyota Cressida 3.0L FI , the Oil Pressure Switch is located: clearpixel.gif Under hood, passenger side, lower engine area, front of oil filter, mounted in engine block clearpixel.gifDavid clearpixel.gif clearpixel.gif

Jul 15, 2008 | 1990 Toyota Cressida

Not finding what you are looking for?
1991 Toyota Cressida Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...