Question about 2005 Dodge Dakota

Open Question

How do you install anti rattle clips on a 2005 dodge dakota 3.7 front dis brake pads

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15 Answers

SOURCE: 2003 Dodge Dakota front end makes click noise only when in a turn

check that the caliper slides are free and that you refiited the anti squel plates on the back of the new pads

Posted on Dec 29, 2008

fknstart
  • 404 Answers

SOURCE: front disc brakes

they should be held on by long spit pins

Posted on Jan 05, 2009

pcastal
  • 90 Answers

SOURCE: 1999 Mustang Cobra anti rattle clips...

whats your email?

Posted on Jan 25, 2009

tse22
  • 103 Answers

SOURCE: Changing Rear brake pads 2005 dodge grand caravan

There are 2 bolts on the "inside" on the caliper towards the bottom they use an allen wrench socket.

Posted on May 13, 2009

  • 2 Answers

SOURCE: 2005 Dodge Grand Caravan brakes

i dont know if this makes sense, if its the big clip, you push in the cylinder and twist until the clipp comes off

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brakes rattle


To your direct question - I don't know the Highlander model in detail, but as a general response, if the brakes are noisy when NOT applied, the piston in your new caliper may not be returning properly.

The return spring in disc brakes is actually the rubber fitted around the caliper piston. If this is causing the piston to be wrongly positioned, the brakes will be noisy. Check that the rotor can be turned by hand when the brakes are not applied. Also check that the piston is not retracting from the pads a very long way, which it should not do.

It is worth making very sure the spring clips are fitted correctly. Some can be easily put in the wrong way round.

If the brakes are squealing when applied, that is a different problem. You can get a disc brake anti squeal liquid, which is applied to the back of the pad on assembly to the caliper. Also double check all the anti squeal shims are correctly installed.

At this range, that's all I can think of right now.

Nov 24, 2011 | 2005 Toyota Highlander

1 Answer

I need to know how to change the front brakes on a 94 jeep grand cherokee laredo.


  1. Raise and support the vehicle safely using jackstands. Remove the wheel(s) on the side to be worked on.

NOTE: Removing a small amount of brake fluid from the master cylinder using a turkey baster


zjlimited_10.jpg

Fig. 4: Tighten the C-clamp until the piston reaches the bottom of its bore


zjlimited_11.jpg

Fig. 5: Remove the caliper mounting bolts


zjlimited_12.jpg

Fig. 6: Slide the caliper off the brake rotor

  1. Drain a small amount of the brake fluid from the front reservoir using a suction gun or a turkey baster.
  2. Place a C-clamp on the caliper so that the solid end contacts the back of the caliper and the screw end contacts the metal part of the outboard brake pad.
  3. Tighten the clamp until the caliper moves far enough to force the piston to the bottom of the piston bore. This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly
zjlimited_13.jpg

Fig. 7: Support the caliper so that no tension is placed on the brake hose


zjlimited_14.jpg

Fig. 8: Hold the anti-rattle clip while removing the outboard pad (4)


zjlimited_15.jpg

Fig. 9: Removing the outboard brake pad


zjlimited_16.jpg

Fig. 10: Remove the inboard pad and anti-rattle clip


zjlimited_17.jpg

Fig. 11: Removing the inboard brake pad


zjlimited_18.jpg

Fig. 12: Removing the anti-rattle clip

  1. Remove the C-clamp.
Do not push down on the brake pedal or the piston and brake pads will return to their original positions up against the rotor.
  1. Remove the caliper mounting bolts. Tilt the top of the caliper outward and lift it off the rotor.
  2. Hold the anti-rattle clip against the caliper anchor plate and remove the outboard brake pad.
  3. Remove the inboard pad and the anti-rattle clip. Be sure that the support spring is removed with the inboard pad.
zjlimited_19.jpg

Fig. 13: Install the support spring onto the shoe of the inboard brake pad


zjlimited_20.jpg

Fig. 14: Installing the inboard pad


zjlimited_21.jpg

Fig. 15: Piston extension on new and worn brake pads

  1. Use a piece of wire to support the caliper so that no tension is placed on the brake hose. Do not allow the caliper to hang by the brake hose.
To install:
  1. Clean all the mounting holes and bushing grooves in the caliper ears. Clean the mounting bolts. Replace the bolts if they are corroded or if the threads are damaged. Wipe the inside of the caliper clean, including the exterior of the dust boot. Inspect the dust boot for cuts or cracks and for proper seating in the piston bore. If evidence of fluid leakage is noted, the caliper should be rebuilt.
Do not use abrasives on the bolts in order not to destroy their protective plating. You should not use compressed air to clean the inside of the caliper, as it may unseat the dust boot seal.
  1. If not already in place, attach the support spring to the inboard brake pad.
  2. Install the anti-rattle clip on the trailing end of the inboard pad's anchor plate. The split end of the clip must face away from the rotor.
  3. Install the inboard pad in the caliper. The pad must lay flat against the piston.
  4. Install the outboard pad in the caliper while holding the anti-rattle clip.
  5. With the pads installed, position the caliper over the rotor.
Before securing the caliper, ensure the brake hose is not twisted, kinked or touching any chassis parts.
  1. Lubricate the caliper pins and bushings with silicone grease. Line up the mounting holes in the caliper and the support bracket and insert the mounting bolts. Make sure that the bolts pass under the retaining ears on the inboard shoes. Push the bolts through until they engage the holes of the outboard pad and caliper ears. Thread the bolts into the support bracket and tighten them to 7-15 ft. lbs. (9-20 Nm).
CAUTION On models with manual/power brakes, pump the pedal until the caliper pistons and brake shoes are seated. On models with anti-lock brakes, turn the ignition ON and allow the booster pump to build pressure. Pump the brake pedal until the shoes are seated and the indicator lights turn off.
  1. Fill the master cylinder with brake fluid and pump the brake pedal to seat the pads.
  2. Install the wheel assembly and lower the vehicle. Check the level of the brake fluid in the master cylinder and fill as necessary.

Remember to rate this, good luck.

Nov 04, 2010 | 1994 Jeep Grand Cherokee

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

How to change front brake pads on 2003 Chevy Suburban


Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket 93086g95.gif

  1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
  2. Raise and support the vehicle safely.
  3. Remove the wheel and tire assembly.
  4. Compress the brake piston back into its bore using a C-clamp.
  5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
  6. Remove the inboard and outboard pad.
  7. Remove and discard the anti-rattle clips.
To Install:
Caliper bracket sleeves 93086g97.gif

  1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
  2. Install new anti-rattle clips.
  3. Position the inboard and outboard pads into the support bracket
  4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
  6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
  7. Install the tire and wheel assembly. Lower the vehicle.
  8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
  9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.
Rear To Remove:
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
  5. Remove the brake pads from the caliper mounting bracket.
  6. Remove and discard the anti-rattle clips.
Rear brake caliper 93086g96.gif

To Install:
  1. Install new anti-rattle clips.
  2. Position the brake pads to the caliper mounting bracket.
  3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
  5. Install the wheel and tire assembly.
  6. Lower the vehicle.
  7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.
prev.gif next.gif

Jul 05, 2010 | 2004 Chevrolet Suburban

3 Answers

My left front wheel squeeks until i press the break pedal


Most likely the brake shoe in that wheel is worn down to the rivets and those metal rivets are scraping on the drum. If you have a new brake shoe installed right away you will be ok. if you wait, you may also have to have the drums turned. By the way brake shoes come in pairs so they will change both front brake pads. Joe

Mar 01, 2010 | 1999 Dodge Dakota

1 Answer

Brake pad replacement


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
ff17c9d.gif
Place a C-clamp over the caliper as illustrated

b802acb.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

1 Answer

How do i replace front pads on 2005 chrysler pacifica


PLEASE DON'T FORGET TO RATE!!!!

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
24539c8.gif
Place a C-clamp over the caliper as illustrated

6ccd8b6.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

1 Answer

2006 dodge ram 2500 4x4 diesel replace brake pads front and back


Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Apr 25, 2009 | 2004 Dodge Ram 2500

1 Answer

Worn brake pads


Front brake pad exchange guide.

Step1 Park the Dodge Durango on a flat surface. Put the emergency brake on and put wedges behind the wheels to prevent the vehicle from rolling. Disconnect the negative battery cable from the battery. Drain 2/3 of the brake fluid from the master cylinder, using a syringe. Remove the wheel and the tire assemblies. Step2 Compress the caliper piston back into the caliper bore using a large C-clamp to drive the piston into the bore. Use additional force if it is required. Using a 3/8 inch hex wrench or socket remove the caliper mounting bolts. Step3 Rotate the caliper rearward off the rotor and out from its mount. Remove the inboard and outboard brake pads. Remove the spring clip that holds the inboard brakes in the caliper. Tilt the pad out at the top to unseat the clip. Remove the retaining spring that secures it in the caliper. Unseat one spring end and rotate the pad out of the caliper. Step4 Suspend the caliper assembly from the Durango frame using mechanic's wire. Do not allow the caliper assembly to dangle from the brake hose as this may damage the brake hose. Step5 Clean the surfaces of the caliper and steering knuckle with a wire brush. Apply multi-mileage grease or similar product. Using brake fluid or break cleaner clean the caliper slide pins. Apply a light coating of silicone grease to the pins. Step6 Install the inboard brake pad and it's spring. Install the outboard brake pad. Install the caliper over the rotor and seat it in its original position until it is flush. Using a torque wrench, torque the slide caliper pins to 22 ft./lbs. Step7 Add brake fluid to the master cylinder. Bleed the brakes. Reconnect the negative battery cable to the battery. Start the engine and pump the brakes 3-4 times to seat the brake pads. Reinstall the wheels. Test drive the Durango at slow to moderate speeds to ensure that the maintenance was performed correctly.
Rear brake pad exchange.

Step1 Lift the Durango off the ground with a car jack. Support the vehicle on all sides with jack stands. Keep children and small animals out of the vicinity when you replace the brakes. Step2 Loosen the lug nuts on the wheels with a torque wrench. Remove the wheel and tire assemblies and set them aside, face up, to prevent damage. Step3 Compress the caliper and remove it by lifting the top up and off the caliper adapter. Hang the caliper from the Durango's frame with mechanical wire. Step4 Remove the inboard and outboard brake shoes from the caliper adapter. Take off the top and bottom anti-rattle springs. Keep the springs separated, as they aren't interchangeable. Step5 Press the piston into the bore with a C-clamp. To prevent damage to the pistons, insert an old brake shoe in between the C-clamp and caliper piston. Remove the C-clamp. Step6 Wipe down the caliper mounting adapter and anti-rattle springs with brake cleaner. Grease the anti-rattle springs with brake grease. Install the bottom anti-rattle springs, followed by the top anti-rattle springs. Step7 Install the inboard brake shoes followed by the outboard brake shoes. Replace the caliper and the wheel and tire assemblies. Lower the vehicle to the ground and pump the brakes to seat the pistons.


Please rate and god bless:)


Apr 02, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
2005 Dodge Dakota Logo

Related Topics:

614 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...