Question about 1995 Ford Bronco

2 Answers

When buying rotors for a 95 Bronco 4X4 should the rotors be seperate from the hub or should they be attached as one piece? Im getting mixed info from part stores.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

The reason you're getting mixed info from parts stores is because it comes both ways.
Look at the following to determine which one you have, 4 wheel disc brakes (floating front rotors) or rear drum brake model (except 4 wheel disc brakes):
Brake Disc (Rotor) REMOVAL & INSTALLATION Except F-Super Duty with 4-Wheel Disc Brakes Fig. 1: Secure the caliper so there is no tension on the brake hose When buying rotors for a 95 Bronco 4X4 should the - 88289p22.jpg

  1. Jack up the front of the truck and support it with jackstands. Remove the front wheel.
  2. Remove the caliper assembly and support it on the frame with a piece of wire (or something equally secure) without disconnecting the brake fluid hose.
  3. Remove the hub and rotor assembly.
  4. Install the rotor in the reverse order of removal, and adjust the wheel bearing as outlined in Section 1.
F-Super Duty with 4-Wheel Disc Brakes The hub and rotor are individual pieces, allowing the rotor to be replaced independently. The front and rear rotors are the same and are attached with 10 bolts and washers. The bolts are tightened a little at a time, in a crisscross fashion, to an ultimate torque of 74–89 ft. lbs. (100–121 Nm). prev.gif next.gif

Posted on Sep 03, 2010

  • hdavis844 Sep 03, 2010

    Is there a place that I can get step by step instructions on changing brakes? What would you think a 95 XLT would have? Wheel disk brakes or rear drum?

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

You can get them both ways, if hub's are good, I would just get the rotor's by them self, to install the rotor, you would have to knock out the stud's from the rotor, to install new one, the stud's is what holds the brake rotor to the hub assembly, that's not that bad of a job to do, also much cheaper for just the rotor's by them self, Napa part number 4886438, and cost about $35.00 each, hope this was very helpful.

Posted on Sep 03, 2010

  • Alexander Mimun
    Alexander Mimun Sep 03, 2010

    Your has brake drum's in the rear, rotor's in the front, and we know that cause your looking to buy rotor's, all 95 Ford Bronco 2 or 4 wheel drive, brake shoes rear and brake pads front.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Im trying to replace the rotors and im having a Hard time getting it off. HELP


You might want to spray some WD-40 around the center of the rotor and the wheel lugs. Usually on Honda's, the rotors will have 2 threaded holes to put in bolts. Screw in each bolt equally to help push the rotor away from the hub.

May 12, 2010 | 1995 Honda Accord

2 Answers

Take rotor off 4x4 bronco


I've got a 96' with manual turning hubs,before I go into 4 wheel drive I have get out and turn them onto lock,when I change my rotor, as soon as I took that part off,and whatever parts came out with it,and then you have to look real close of the inner hub there is a ring in there you have to get that out now your get to the outer lock nut,you'll need a spanner locknut wrenchto loosen it,next is lockwasher you can pull it out then you got inner lock nut take it out ( when you put that back you can hand tighten it) the rotor should come out

Feb 11, 2010 | 1996 Ford Bronco

1 Answer

I want to remove the hub and rotor as one piece its manual


i don't think you can . you have to remove the hub to get to the nut that hold the bearings and rotor on to spindle.

Nov 07, 2009 | 1993 Ford Bronco

1 Answer

Changing the rotors out on my 83 4x4 bronco


I would start with the simplest of solutions and try bleeding the breaks and checking the lines for any leaks. Second, if the brakes were properly bled and there is no leak apparent, I would remove the front caliper on the left side, and have a friend pump the brakes, and see if there is pressure on the caliper itself. It is likely that you may have broken or otherwise damaged a brake line, or the caliper simply chose this mos inconvenient of times to die.

Jun 18, 2009 | 1983 Ford Bronco

1 Answer

Help with rotors please


you have to knock out all the wheel studs first. these are pressed in, just hammer them out then you can hammer the rotor off by placing hub and rotor, outer side up on flat surface. this will probably destroy the rotor but im assuming you are replacing them anyway

May 03, 2009 | 1994 Ford Bronco

2 Answers

Hi how do i take of the front rotor for a 94 ford bronco?


have you got the wheel off, this is first step. next take off the pads and caliper. you dont have to disconnect the brake line. next there is a cotterpin and bolt holding the rotor on( in the center under a cap w grease in it), remove these and it should come off. if its rusted on youll have to hammer it a bit.

Apr 22, 2009 | 1994 Ford Bronco

1 Answer

98 chev p/u c/K1500 wheel rotor and hub assembly


they are manufacturered in one piece, i would say it's broken and needs replacing

Jan 09, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Changing brakes and rotors


Remove te cross pins that hold the caliper and the brake pads in place, then remove the caliper bracket, there are 2 bolts at the backside, then the rotro just slides off, clean any rust on the rotor mount area while the rotor is off, then using a large clamp depress the piston in the brake caliper and reinstall in reverse order, one word of caution, use quality replacement parts, Wagner is very good, if you don't use good parts you will end up with poor brake performance.

Oct 15, 2008 | 1990 Ford Bronco

Not finding what you are looking for?
1995 Ford Bronco Logo

618 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...