Question about Chrysler 300

1 Answer

On a 1999 300 I can not get the oil pan to drop out. It hits the front and the the flywheel in the rear. It looks like the engine needs to be raised. Can this be?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 8,266 Answers

Yes, this is often the case. Determine which end should be raised, and unbolt the motor mount on that side. Find a solid place to push up on the engine and jack it up a few inches at most. If no good place to jack, can possibly pry up from above using a 2 by 4, but be careful not to slip the pry while removing the pan.

Posted on Sep 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.


REMOVAL PROCEDURE
  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

May 04, 2015 | 1998 Chevrolet Chevrolet silverado

1 Answer

How to remove oil pan



4x4
1. Open the hood.
2. Disconnect the battery negative cables.
3. Remove the intake air assembly.
4. Remove the radiator shroud retaining bolts.
5. Install engine support fixture # 8534B .
6. Raise and support the vehicle.

WARNING: HOT OIL CAN CAUSE PERSONAL INJURY.


7. Drain the engine oil (Refer to 09 - Engine/Lubrication/OIL - Standard Procedure) .
8. Loosen the front engine mount bolts.
9. Lower the vehicle.
10. Use the engine support fixture # 8534B to raise engine out of the front mounts.
11. Remove the engine oil dipstick.
12. Raise and support the vehicle.
13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
14. Remove oil pan and suction tube.
15. Remove the 2 bolts from the front of the engine block stiffener.
16. Remove the oil pan.


4x2
1. Open the hood.
2. Remove the negative battery cables.
3. Raise and support the vehicle.
4. Remove the transmission oil cooler lines.
5. Remove the propeller shaft.
6. Remove the starter bolts.
7. Support the starter.
8. Remove the torque converter bolts.
9. Remove the exhaust hanger bolts.
10. Remove the gear shift cable.
11. Remove the wiring harness.
12. Remove the transmission mount.
13. Remove the crossover bolts.
14. Position the transmission jack.
15. Remove the bell housing bolts.
16. Remove the transmission.
17. Remove the flywheel housing bolts (8).
18. Remove the flex plate bolts (8).
19. Remove the engine oil dip stick.
20. Drain the oil.
21. Remove the steering rack bolts.
22. Remove the oil pan bolts.
23. Remove the oil pickup bolts.
24. Remove the oil pan. user_online.gif

Aug 01, 2014 | Dodge Ram 3500 Cars & Trucks

1 Answer

Change oil pan on a 2001 sonoma


the 2.2 engine and the 4.3 engine with 2WD MODEL you have to remove engine.the 4WD MODELS, you have to remove all these parts first remove dip stick, drive belt, splash shield, remove front axle shield and the transfer case shield, front skid plate and the flywheel cover,remove left and right engine mount through bolts.then raise the engine using a lifting device, and block in position,using large wooden blocks between the motor mounts and brackets.you will also need to remove these parts,remove disconnect oil cooler line, remove pitman aem bolt and pitman arm, remove idler arm bolts and idler arm, remove front differential through bolts,remove front driveshaft if necessary,remove differential assembly by rolling it forward for clearance, remove starter motor, then remove oil pan bolts then remove oil pan, your oil pan need to be flushed slightly forward of rear of the block to allow proper alignment with the transmission housing.using feeler gauge measure the 3 oil pan to transmission contact points.clearance should not exceed 0.011 in. 0.3mm if so realign the oil pan.oil pan bolts torque is 18 ft lbs tighten oil pan bolts in sequence.

Aug 25, 2012 | Cars & Trucks

1 Answer

I need to know if i remove flywheel or ac compressor to remove oil pan


procedure is pasted below. Yes, you have to take the compressor loose if you have the 2.4 liter engine. You should never have to remove the flywheel to get the pan off, but you do have to pull the cover off the flywheel. Please let me know if you have any questions, and thanks for using FixYa.

REMOVAL & INSTALLATION

2.2L Engine
See Figure 1
  1. Disconnect the negative battery cable.
  2. Drain the crankcase. Raise and support the front of the vehicle.
  3. Unfasten the exhaust shield and disconnect the exhaust pipe at the manifold.
  4. Remove the starter motor and position it out of the way.
  5. Remove the flywheel cover.
  6. On care equipped with automatic transaxle, remove the oil filter and extension.
  7. Unfasten the oil pan bolts and remove the oil pan.


jturcotte_2045.gif

Fig. Fig. 1: Oil pan installation-1995 2.2L OHV engine shown

To install:

  1. Prior to oil pan installation, check that the sealing surfaces on the pan, cylinder block and front cover are clean and free of oil. If installing the old pan, be sure that all old RTV hae been removed.
  2. Apply a 1 / 8 in. (3mm) bead of RTV sealant to the oil pan sealing surface. Use a new oil pan rear seal and apply a thin coat of RTV sealant to the ends of the gasket down to the ears and install the pan in place.
  3. Tighten the oil pan retaining bolts to 89 inch lbs. (10 Nm).
  4. On care equipped with an automatic transaxle, replace the oil filter adapter seal and replace the oil filter adapter.
  5. Install the remaining components in the reverse order of removal.

2.3L and 2.4L Engines
See Figures 2 and 3
  1. Disconnect the negative battery cable. Raise and safely support the vehicle.
  2. Properly drain the engine oil and the cooling system into suitable containers.
  3. Remove the flywheel housing or transaxle converter cover, as applicable.
  4. Remove the right front wheel and tire assembly, then remove the right splash shield.
  5. Remove the serpentine drive belt.
  6. Unfasten the A/C compressor lower retaining bolts.
  7. Remove the transaxle-to-engine brace.
  8. Disconnect the engine mount strut bracket.
  9. Unfasten the radiator outlet pipe bolts, then remove the pipes from the oil pan.
  10. Remove the exhaust manifold brace.
  11. Unfasten the oil pan-to-flywheel cover bolt and nut.
  12. Remove the flywheel cover stud for clearance.
  13. Disconnect the radiator outlet pipe from the lower radiator hose and oil pan.
  14. Detach the oil level sensor connector.
  15. Unfasten the oil pan retaining bolts, then remove the pan and gasket. Inspect the gasket for damage. If it'e O.K. you can reuse it. No sealer is necessary.

jturcotte_2046.gif

Fig. Fig. 2: After removing the oil pan, inspect the gasket. If it's not damaged you can reuse it

To install:

  1. Position the gasket, then install the oil pan. Loosely install the retaining bolts.
  2. Place the spacer in its approximate installed location by allow clearance to tighten the pan bolt directly above the spacer. Tighten the oil pan bolts to the specifications given in the accompanying figure.

jturcotte_2047.gif

Fig. Fig. 3: Oil pan tightening specifications-2.3L and 2.4L engines

  1. Position the spacer into its proper position, then install the stud.
  2. Fasten the oil pan-to-transaxle nut.
  3. Attach the oil level sensor connector.
  4. Connect the radiator outlet pipe to the oil pan and fasten with the retaining bolts.
  5. Install the engine mount strut bracket.
  6. Fasten the transaxle-to-engine brace.
  7. Secure the A/C compressor bolts.
  8. Install the serpentine drive belt.
  9. Fasten the right splash shield, then install the wheel and tire assembly.
  10. Install the flywheel housing or transaxle converter cover.
  11. Fill the cooling system and engine crankcase with the correct type of fluids.
  12. Connect the negative battery cable.

Aug 09, 2011 | 1998 Chevrolet Cavalier

1 Answer

How to replace oil pan gasket


1994-96 VEHICLES
( see Figures 6 and 7 / click image for zoom )


zjlimited_1359.jpg

Fig. 6: Oil pan mounting bolt locations-1996 3.1L engine shown

zjlimited_1360.jpg

Fig. 7: Oil pan sealant application points-1996 3.1L engine shown

  1. Disconnect the negative battery cable.
It may be necessary to remove the hood, with the help of an assistant, for access.
  1. Remove the engine mount strut and A/C compressor (if equipped) and the engine mount strut bracket assemblies.
  2. Remove the electric cooling fan assemblies. -28467 and J 26462, or equivalent.
  3. Raise and safely support the vehicle. Drain the engine oil.
  4. Remove the front exhaust manifold pipe.
  5. Remove the intermediate shaft bolt/screw.
  6. Remove the oil level sensor.
  7. Remove the engine splash shield.
  8. Suitable support the drivetrain and front suspension with jack stands.
  9. Remove the transaxle mount side frame retaining nuts from the drivetrain and suspension frame assembly.
  10. Remove the engine mount side frame nuts from the drivetrain and suspension frame assembly.
  11. Unfasten the rear drivetrain and front suspension frame bolts/screws.
  12. If equipped, remove the lower drivetrain and front suspension frame bolts/screws.
  13. Remove the engine mount assembly.
  14. Remove the flywheel inspection cover.
  15. Remove the starter.
  16. Disconnect the transaxle mount assembly from the oil pan.
  17. Unfasten the side bolts and screws and the retaining bolts and screws, then remove the oil pan. Remove and discard the oil pan gasket.
To install:
  1. Clean the gasket mating surfaces.
  2. Apply a small amount of sealer on either side of the rear main bearing cap, where the seal surface on the cap meets the cylinder block. Install a new gasket on the oil pan.
  3. Position the oil pan and secure with the retaining bolts and screws. Tighten the retaining bolts and screws to 18 ft. lbs. (25 Nm) and the side bolts/screws using tool J 39505 or equivalent.
  4. Fasten the transaxle mount assembly to the oil pan.
  5. Install the starter motor.
  6. Install the flywheel inspection cover.
  7. Install the engine mount assembly.
  8. Carefully raise the drivetrain and front suspension assembly. Install the rear drivetrain and front suspension frame bolts/screws.
  9. Fasten the engine mount frame side nuts to the drivetrain and front suspension frame assembly. Install the transaxle mount frame side nuts to the drivetrain and suspension frame assembly.
  10. Remove the jackstands from the drivetrain and front suspension frame assembly.
  11. Install the engine splash shield and the oil level sensor.
  12. Install the intermediate steering shaft bolt/screw. Connect the front exhaust manifold pipe.
  13. Carefully lower the vehicle.
  14. Remove the engine support tools.
  15. Install the electric cooling fan assemblies.
  16. Install the engine mount strut and A/C compressor, bracket and the engine mount strut bracket.
  17. If removed, install the hood assembly.
  18. Fill the crankcase to the correct level. Connect the negative battery cable. Run the engine to normal operating temperature and check for leaks.
Hope this helps (remember to rate this answer).

Jun 04, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Instructions on removing an oil pan to replace gasket on a 1995 saturn SL1


  1. Raise the front of the vehicle and support it safely using jackstands. Remove the plug and drain the engine oil from the pan and crankcase.
  2. Disconnect the fasteners from the exhaust manifold flange and the pipe rear flange, then remove the front exhaust pipe and gaskets from the vehicle.
  3. Remove the engine stiffening bracket and the flywheel cover.
  4. Remove the right wheel and splash shield, then loosen the 4 front motor mount bolts. Back the bolts out about 1 / 2 in. (12mm).
  5. Remove all the oil pan bolts. For vehicles with a manual transaxle, an 8mm flex socket may be used to access the rear oil pan bolts located next to the flywheel.
  6. Using SA9123E, or an equivalent RTV cutter tool, separate the oil pan from the engine. Drive the tool around the pan to shear the RTV seam, then tap the pan sideways with a rubber mallet to loosen.
  7. Pry the engine mount away from the engine as necessary and remove the oil pan. Be careful not to damage or score component surfaces when prying.

To install:
  1. Carefully clean the gasket mating surfaces with a scraper and solvent.
  2. Apply a 0.16 in. (4mm) bead of RTV sealer to the pan flange. Make sure the RTV is applied to the inner side of the flange from the bolt holes as shown.
  3. Install the oil pan within 3 minutes of RTV application and tighten the bolts to 80 inch lbs. (9 Nm).
  4. Tighten the front mount bolts to 37 ft. lbs. (50 Nm).
  5. Install the right splash shield and wheel.
  6. Install the engine stiffening bracket and the flywheel cover.
  7. Install the exhaust pipe. Tighten the pipe to manifold nuts in a crosswise pattern to 23 ft. lbs. (31 Nm) and the pipe to converter bolts to 33 ft. lbs. (45 Nm).
  8. Remove the jackstands and carefully lower the vehicle, then fill the engine crankcase with clean engine oil immediately in order to prevent an attempt to start the engine without oil.
  9. Start the engine and check for leaks.

May 19, 2011 | Saturn SL1 Cars & Trucks

1 Answer

How to do an oilpan on a 88 chevy montecarlo


  1. Disconnect battery negative cable.
  2. Remove air cleaner.
  3. Remove upper fail shroud (V8)
  4. Raise vehicle and drain oil pan.
  5. Disconnect A.I.R. hose at converter pipe (V8)
  6. Disconnect A.I.R. pipe at exhaust manifold (V8)
  7. Remove exhaust crossover pipe at manifold and converter.
  8. Remove starter.
  9. Remove flywheel cover.
  10. Disconnect transmission oil cooler lines at oil pan.
  11. Remove engine mount 'through' bolts on V8. Loosen right bolt and remove left on V6.
  12. Remove oil pan bolts and lower oil pan. Check that forward crankshaft throw and/or counter balance weight are not extending downward so to block oil pan removal. Turn crankshaft, necessary, to put throw on horizontal plane.
  13. Raise engine.
  14. Remove oil pan.
Installation


  1. Clean sealing surfaces on cylinder case and pan.
  2. Check oil pan gasket for damage; replace if necessary.
  3. Apply a small amount of 1052751 or equivalent to front and rear corners of oil pan.
NOTICE: Only a small amount of sealant is required. Excessive amounts of sealant may cause a problem with proper sealing of oil pan.


  1. Install retaining bolts and torque to 9 N.m (80 lb. in.).
  2. Raise engine, if necessary.
  3. Lower engine, install mount 'through' bolts and torque to 50 lb. ft. (65 N.m).
  4. Install torque converter cover.
  5. Install starter.
  6. Install exhaust crossover pipe at manifold and converter.
  7. Lower vehicle.
  8. Install fan shroud.
  9. Install air cleaner.
  10. Fill crankcase with oil.
  11. Connect battery negative cable, start engine and check for leaks.

Nov 30, 2010 | 1987 Chevrolet Monte Carlo

1 Answer

How to change oil pump


You need to drop the oil pan. First remove 2 braces to flywheel cover, then unbolt flywheel cover and remove. You may need to unbolt exhaust at manifolds to get this cover out of there. Then un bolt oil pan. Hopefully you will have enough room or raise engine after unbolting engine mounts 2" is usually enough. Unbolt oil pump and remove. If no oil pressure is your problem you may only need to clean out pick up tube and screen and not have to remove pump. If this is a 4x4 transfer case will be in the way.

Sep 25, 2010 | 1995 GMC Yukon

1 Answer

Need to change oil pan


e
Cavalier, Sunfire 2001-2005

Oil Pan - Removal & Installation

2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Right front wheel Right inner fender splash shield Starter motor and bracket Engine mount strut bracket Oil pan
To install:


672c0b8.jpg

Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
  1. Place a 2mm bead of RTV sealer to the oil pan sealing surface except at the rear seal mounting surface. Using a new oil pan rear seal, apply a thin coat of RTV sealer on the end down to the ears.
  2. Install or connect the following:
    Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm). Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm). Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Right fender splash shield Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm). Negative battery cable
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.
2.2L (VIN F) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine mount strut bracket Drive belt Lower then upper AC compressor bolts Oil pan bolts Oil pan

    1c9e9c9.jpg

    Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
To install:
  1. Apply a 2 mm bead of RTV sealant around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install or connect the following:
    Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm) AC compressor bolts Engine mount bracket Drive belt
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.

2.4L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Flywheel/converter cover Right wheel Right wheel well splash shield Accessory drive belt Air conditioning compressor lower bolts Transmission-to-engine brace Engine mount strut bracket Radiator outlet pipe bolts Radiator outlet pipe from the oil pan Oil pan to the flywheel cover bolt and nut Flywheel cover stud for clearance Radiator outlet pipe from the lower radiator hose and oil pan Oil level sensor connector Oil pan
To install:
  1. Inspect the oil pan gasket; it is reusable if not damaged.
  2. Install or connect the following:
    Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).

    2ffc5e9.jpg

    Fig. Oil pan fastener torque specifications-2.4L engine
    Oil pan to the transmission nut Oil level sensor connector Radiator outlet pipe to the lower radiator hose and oil pan Exhaust manifold brace Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm). Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm). Transmission to the engine brace Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Accessory drive belt Right splash shield Right front wheel Flywheel/converter cover Negative battery cable
  3. Refill the crankcase.
  4. Refill the cooling system.
  5. Start the vehicle and verify no leaks.

Hope helped (remember rated this help). Good luck.

Oct 22, 2009 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...