Question about Ford Ranger

Open Question

Diagram for 1990 Ford Ranger transmission? - Ranger Ford Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

johnny5846
  • 379 Answers

SOURCE: firing order diagram for 1986 ford ranger

you will find this site usefull , here is the diagram for 1986 ford ranger 2wd 2.9liter v6 firing order .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm


Fix Ya vote is my Reward , thanks .

Posted on Jan 08, 2009

localwonder
  • 6784 Answers

SOURCE: 2004 ford ranger edge 3.0L spark plug wire diagram

The diagram you seek is below.


374d96b.jpg

Posted on Jul 26, 2009

  • 2002 Answers

SOURCE: Looking for a diagram for a ford e4od transmission

Rebuilding an automatic transmission requires more than looking at a diagram. Check out faxonautoliterature. They have the original Ford service manual for your truck and it will have all the information that you will need to rebuild your trans properly. Hope this helps.

Posted on Oct 07, 2009

wfservices
  • 260 Answers

SOURCE: Diagram of 1996 ford ranger fusebox which fuse is

RANGER FUSE PANEL Fuse Position Rating Circuit Protected 1 7.5 Amp Power Mirror 2 — Not Used 3 15 Amp Parking Lamps 4 10 Amp Left Headlamp 5 10 Amp On Board Diagnostic (OBD) II System 6 7.5 Amp Air Bag System/Blower Relay 7 7.5 Amp Illumination Switches 8 10 Amp Right Headlamp/Fog Lamp System 9 10 Amp ABS System 10 7.5 Amp Speed Control/GEM System/Brake Interlock 11 7.5 Amp Warning Lamps 12 10 Amp Front Washer System 13 15 Amp PCM System/Stoplamps/
4WD/ABS/Speed Control 14 10/20 Amp ABS System 15 7.5 Amp Air Bag System/Alternator 16 30 Amp Front Wiper 17 15 Amp Cigar Lighter 18 15 Amp A/C System 19 25 Amp Ignition Coil/PCM System 20 7.5 Amp Radio/GEM System/Anti-Theft 21 15 Amp Hazard Lamps 22 10 Amp Turn Signals 23 — Not Used 24 10 Amp Starter Relay/Anti-Theft 25 7.5 Amp Speedometer/GEM System 26 10 Amp 4R44E/4R55E Trans./Backup Lamps/DRL System 27 10 Amp Underhood LP/Map Lights/Glove Box Lamp/Dome Lamp/Visor Lamps/4x4 Sys. 28 7.5 Amp GEM System 29 10 Amp Audio System 30 — Not Used 31 — Not Used 32 — Not Used 33 15 Amp High Beam Lamps 34 — Not Used 6d47eae.gif

Posted on Mar 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990-1992 ford ranger/expedition automatic transmission not moving/slipping when in gear


replace tran filter and fluid easy fix! Usually or Trans tuneup at any trans shop just dont leave its side they have fun with our cars to make lots of money may just need to retighten the bands and change filter add new fluid

Jul 28, 2012 | 1990 Ford Ranger SuperCab

1 Answer

Wheares number 1 on cap for 1990 ford ranger


if you have the 3.0 the firing order is 1 - 4 - 2 - 5 - 3 - 6 heres, a diagram of an explorer which is the same 3.0 http://www.fixautopartz.com/2009/11/06/ford-explorer-2-9l-and-3-0l-engines-firing-order

Jul 10, 2011 | 1990 Ford Ranger SuperCab

1 Answer

Need ford ranger 1990 engine 2.9 liter firing order diagram for wires and plugs, please call or email below 571-237-5328


For 1990 Ford Ranger 2.9 liter V-6 VIN "T" check the next firing diagram...


zjlimited_403.gif


Hope this helps (remember to rate and comment this free answer)

May 31, 2011 | Ford Ranger Cars & Trucks

1 Answer

I need a belt routing diagram for a 1990 ford ranger 2.9 liter


dd07c7b.jpg

Here is the routing for that setup. i hope this helps!!!

Oct 08, 2010 | 1990 Ford Ranger SuperCab

1 Answer

Need a stereo wiring diagram for a 1990 ford ranger pickup


If your local Ford dealer hasn't purged the manual the should make a copy of the schematic for you

Jul 25, 2010 | 1990 Ford Ranger SuperCab

3 Answers

Looking for a fuse diagram for a 1992 ford ranger.


tail lights wont come on my 1992 ford ranger xlt but brake lights and back up lights work also instrument panel lights wont come on

Jan 15, 2010 | 1992 Ford Ranger

1 Answer

1990 ford ranger power steering full install


if fluid is full the pump is no good check to see if fluid is moving around in res if it is you have a bad rack

Mar 10, 2009 | 1990 Ford Ranger SuperCab

1 Answer

I need a spark plug wiring diagram for a 1990 Ford Ranger 2.3L


auto parts stores should be able to tell you your firing order

Feb 26, 2009 | 1990 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

508 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...