Question about 1996 Toyota Corolla

1 Answer

Replaced rear brake shoes on 1996 corolla and emergency brake does not work

Posted by on

  • Anonymous Mar 22, 2014

    back brake shoe replacement

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 31 Answers

If it is rear disk the parking braek is inside of the disk

Posted on Sep 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear drum brakes


Sounds like brake shoes are knocking. Try backing up while pumping brakes or using the emergency brake a few times to tighten up shoes. If those don't work you may have to manually adjust shoes with star wheel or maybe defective (out of round) drum

Sep 17, 2016 | 2006 Chevrolet Equinox

Tip

Removing rear rotors


On the rear wheels, the inside of the rotors act as a drum for the emergency brake shoes. You must loosen the emergency brake so that the shoes back away from the inside walls of the rotor. Loosen the emergency brake, left and right side, by loosening both nuts at the emergency brake handle. Further, the emergency brake's internal adjusting nuts are accessible through the lug holes in the hub. Then remove the rear rotors

on May 19, 2008 | 1987 BMW 5 Series

1 Answer

Emergenct brake will not hold


The linkage could need to be adjusted. Or the brake shoes inside the rear drums are worn out and need to be replaced. If you accidentally drive the brake on. It doesn't take long to wear those brake shoes out. You can normally smell them when that happens. On today's vehicles they are actually designed with 3 different brake systems. Front brake disc and rotors, rear disc and rotors, and inside the rear brake rotor their is a small brake drum where the emergency brake shoes are located. The only purpose for the shoes and drums is emergency brake only (normally). Hope this helps.

Nov 27, 2012 | Cars & Trucks

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

1 Answer

Where doe's that spring go on rear brake drums 1996 chevy truck every thing is at top not at bottom, star wheel adjuster?


there should be several springs. first there are (2) real short springs that hold the shoes to the dust cover/back plate. they go in the center of each shoe. then there is a short spring that goes at the bottom where the adjuster is located. there should be a hole in each shoe. finally there is a long spring that goes at the top where your brake cylinder is and this is what gets attched last after your emergancy brake levers are placed between the shoes .

Apr 17, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Emergency Brake Loss


Good day;
After you put it all back together did you drive the car in reverse then apply park brake? If not give this a try, just use your hand park to stop the car, these should fix the problem,Let me know how you made out.

Cheers

Aug 27, 2008 | 2001 Toyota Corolla

2 Answers

1996 Dodge stratus rear end whine


My drum brakes were worn and made a noise back there, perhaps the shoes are dragging?

Aug 11, 2008 | 1996 Dodge Stratus

1 Answer

Brakes system for 2001 toyota corolla


it should have disk brakes all round but shoes for the hand brake on the rear. unless you have the"poverty pack" it may just have shoes on the rear.....

Jul 10, 2008 | 2001 Toyota Corolla

1 Answer

1996 toyota corolla rear drum brake (Australia)


to remove a stuck brake drum what I do is. there is a couple of holes in the drum a size 10mm nut screw hole. get two 10mm bolts screw it in the two OPPOSITE holes and screw in at the same time until the drum is free. we call this screws extractor. Check for any damage in the shoe and other parts because you are force extracting the drum

Jun 28, 2008 | 1996 Toyota Corolla

3 Answers

Rear brakes on 2005 F150


You can't remove the rotors because the emergency brake is tight on the inside of the rotors. Make sure it's not engaged when you are working on the rear brakes. Block the front tires for saftey. Then you have to remove the rear calipers from the mounting brackets, there are two bolts that hold the calipers on. Make sure you hang the calipers securily with some wire so you don't damage the rubber brake line hose. Then you need to adjust the emergency parking brake shoes in order to remove the rotors. Theres a rubber plug on the backside of the rear hubs, once you look at the back of the hub you'll see the plug. It's on the top. Once you take out the plug, you need to use a screw driver to turn the star spindel. You need to turn the star spindel counter-clockwise in order to give yourself enough clearance to remove the rotors. The beauty of this design is that ford incorporated a drum and caliper system together, but it's difficult to take off the rotors if the emergency brake shoes are to tight. The inside of the rotors acts as the drums for the emergency brake system. I've done this and it's not that hard, but, I did have to replace the emergency brake shoes because they were worn out and the shoes fell off the metal backing plates when I finally got the rotors to come off. They only glued these shoes onto the backing plates, they don't rivet them so take your time getting the rotors off or you can damage the emergency brake shoes, but if you do they are cheap at napa. My service guide says to install the new rotors, use a couple of lug nuts to hold it on, then adjust the star spindal for the emergency brake all the way clockwise until you can't turn it anymore, then you must back it off 8 clicks counter-clockwise. Make sure the emergency brake is not engaged when you are doing this, the 8 clicks backwards compensates for when you do engage the parking brake because the shoes expands outwards. This adjustment sets the emergency brakes so they work properly. Once the emergency brake is properly set you can't remove the rear rotors, which is what your initial problem is. Then install the rubber plug back in the hole, put on the new pads and calipers and you're good to go.

Jun 25, 2008 | 2005 Ford F-150

Not finding what you are looking for?
1996 Toyota Corolla Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...