Question about 1999 Jeep Cherokee

1 Answer

Hazard lights turn on when i use my turn signal

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

Your model uses a combination hazard/turn signal relay.You need to remove the knee plate and its up to the left of the steering column.You need to reach up and remove the flasher unit and replace.Hope this helps

Posted on Sep 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

Fix signal lights


If the hazard flasher is working but the turn signals aren't, the problem is most likely either fuse A11 or the #2 relay in the trunk fuse block. However, if these check out, the problem could be either the turn/hazard switch assembly or the turn flasher module.

If both the turn signals and hazard flasher are not working, the most likely problem is the turn/hazard switch assembly.

May 03, 2015 | 1996 Cadillac DeVille

1 Answer

How do I fix both turn signals and hazard lights on 1995 Buick custom regal?


First off operate the hazard switch many times. The contacts in the switch corrode through lack of use and this will clean them. As the turn signals and hazard lights share the turn signal unit it may be faulty.

Feb 24, 2015 | Buick Cars & Trucks

1 Answer

Turn signal and hazard lights are not workin


Probable cause is what we used to call a stacker switch, Your car should have 2 of them, 1 for the turn signals and 1 for the flashers or hazard lights, Normally the turn signal switch is located in the fuse box, a round plug in switch, easy to change and cheap too.

Nov 14, 2013 | 1998 Mercury Grand Marquis

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

2 Answers

92 caprice classic turn signals not working, but the bulbs are fine. Hazards, brakes, etc all work fine. Any ideas?


Yes, the problem is the turn signal flasher is defective. You can has two flasher relays. One for the turn signals and one for the hazard lights. That is why the hazard lights flash and the turn signals do not. Replace the turn signal flasher relay located on the drivers side of the steering column, mounted behind the instrument cluster in the convenience center. They are both mounted in the same location so turn on the hazard lights and the one that you put your finger on that is not clicking is the turn signal relay.

Mar 08, 2011 | 1992 Chevrolet Caprice

2 Answers

Turn signal doesn't come on until I hit my hazard light on & off


it could be duel filament bulb that is blown and shorting inside the bulb to the other circuit, you may need to remove all indicator and hazard bulbs and check. I would also try a new flasher can

Apr 17, 2010 | 2003 Chevrolet Impala

1 Answer

No brake/hazard lights,have running/turn signal lights


Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

May 11, 2009 | GMC Sierra 2500 Cars & Trucks

Not finding what you are looking for?
1999 Jeep Cherokee Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...