Question about 1994 Nissan Pickup

1 Answer

Need a carburetor - 1994 Nissan Pickup

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 2,019 Answers

The only thing that ever goes wrong with carbs is they get clogged up. So taking them apart, soaking, and blowing out with compressed air almost always fixes them.
If not, there are lots of places that sell rebuilt ones.
http://nationalcarburetors.com/

Posted on Sep 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Daf 85 hard to start,turning over for about 30 seconds before starting.any ideas what the problem could be?


Sure!
Your car should have a carburetor, instead of being fuel injected.
If it does, likely the carburetor needs to be overhauled.
In most carburetors, there is a needle and seat and a float, which, when the fuel bowl is full, that float pushes on the needle and shuts off further fuel until the level gets low again from driving.
When the needle gets dirty, the fuel can actually drain back to the fuel tank when you turn off the engine, emptying the carburetor.
Then you would need to "pump the fuel up to the carburetor" again to fill the bowl before the car will start.
I would take that amount of time.
God bless your efforts.

Oct 19, 2017 | DAF Cars & Trucks

1 Answer

I have a Chinese motor go kart put new carburetor on it can remember were all the hose connect from carburetor to the gokart needing diagram


Should be 1 hose from the gas tank bottom .that goes into the top hose connection on the carburetor . The smallest hose goes from the bottom of the carburetor to top of the tank . If you have a large hose it should be for the air breather.

Nov 08, 2014 | Cars & Trucks

1 Answer

I HAVE A 1988 MUSTANG 5.0 THAT HAS BEEN SITTING FOR ABOUT 3 YEARS. I HAVE PUT NEW PLUGS AND WIRES ,NEW GAS WILL TURN OVER BUT WONT START


Check the fuel pressure at the Carburetor or fuel rail, depending on which you have. Most likely the gas that was in the rail or carburetor has dried out and gummed up the injectors or needle valve holes. To verify, if you have a carburetor you can pour a small amount of gas in the throttle body of the carburetor and try to start it. If it starts that confirms the problem and you will need to clean the carburetor with a rebuild.

Sep 27, 2011 | 1988 Ford Mustang

1 Answer

Need a pic and specs on a 1979 gmc sierra grande carburetor


That is a Rochester carburetor--4 barrel, and these carburetor are notorious for problems. It's a hassle to repair because some of the flat plug in the passage ways will leak. We just drill them out, and install new plug with epoxy after the carburetor body has been thoroughly cleaned. Go to you local library they should have a repair manual on Rochester carburetors, or look on the Internet it has everything in it networking. GB...stewbsion

Aug 21, 2011 | GMC Sierra 1500 Cars & Trucks

1 Answer

I need rebiuld my carburaitor is all ready clean (I cleaned in carb.& parts cleaner) blowt-aut whit 90 psi I have new repear kid only Ineed the diagram or manual to putin back togader


THE CARBURETOR KIT HAS A DIAGRAM ON HOW TO ADJUST FLOATS AND PUT CARBURETOR BACK TOGETHER.EVERY CARBURETOR I REBUILT HAD A DIAGRAM TO REASSEMBLE PUT CARBURETOR BACK TOGETHER.

Apr 30, 2011 | Mazda B2200 Cars & Trucks

1 Answer

Need the linkage diagram for a 1978 dodge brougham carbuator with a 440 motor


Hi!!
In order to better assist you, please provide the carburetor part #, it is located as follows: On Carter Carburetors, the number is stamped on the left rear foot of throttle body on vertical surface near bolt hole. The Carburetor number is preceded by the letters "TQ" and followed by an "S". On Holley Carburetors, the number is stamped on main body flange. It is in front of the lever, controlled by throttle position transducer, under the choke vacuum diaphragm. The Carburetor number is preceded by the letter "R" and followed by an "A".
Thanks

Dec 02, 2010 | Dodge 400 Cars & Trucks

1 Answer

My truck stopped running while driving and would not start. Fuel was coming out the carburetor when the key is turned on. Why?


It sounds like your needle an seat in the carburetor got a small particle of dirt or rust or something in it all you can do is tap the carburetor with like the handle of a screwdriver or tap the carburetor in a few different places with a rubber or plastic hammer that might fix it for awhile but you will need to buy a carburetor rebuild kit.

Sep 04, 2009 | 1990 Mitsubishi Mighty Max

Not finding what you are looking for?
1994 Nissan Pickup Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79024 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...