Question about 1994 Chrysler Concorde

1 Answer

Back brakes nut for holding rotors, size? - 1994 Chrysler Concorde

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I'm assuming you want to remove the rear rotors. No rear brake rotor nut for holding the rotor on that I know off. I just had my rear rotors off and turned on my 94 Concorde LX.
After removing the tire I diligenty removed the star washers (2) from the lug studs. Then a little spray of PB Blaster around the center hub. Next I removed the 2 10mm bolts holding the caliper to the rotor. A slight nudge with a rubber mallet and the caliper is free, but do support it, don't let it dangle. Another slight nudge on the rotor with a rubber mallet and the rotor literally fell off the car.
There is a rear axle nut and bearing inside of the center hub that is secured by a large 34mm hex nut, on the outside of that a lock ring that looks like a large black bottle cap with a cotter pin going through it for retention. That has nothing to do with removing the rotors. With a little patience, lubricant and gentle tapping, the rotors slide off the center hub. Hope this helps.

Posted on Sep 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size allen wrench for brake calipers on 2001 Dodge Dakota 2WD 3.9L and what size is the nut holding the rotor on? Standard or Metric?


a 7 mm hex head wrench for the caliper bolts. the nut that holds the bearings in place is usually a 1 inch or 1 1/16 inch, but a pair of pliers should be enough to take the nut off after the cotter pin is removed. when you put the nut back on DO NOT over tighten it or you will damage the wheel bearings.

Aug 07, 2011 | 2001 Dodge Dakota

3 Answers

WHy dose my brake pedal push back and make a grinding noise


Look through the openings in your front wheels and look at the front rotors-are they gouged up? You are probably running metal-to-metal, pads to rotors.
Chances are real good your rotors will have to be replaced along with new pads, but if you catch it early enough you might be able to have them machined, although nowadays that is hardly easy to get done and the savings usually is not as significant as it once was.

May 23, 2011 | 1995 Pontiac Bonneville

1 Answer

After removing the tire, there is a hub type assembaly that appears to be bolted onto the rotor, after plenty of PB oil and some TLC, i managed to break this assembaly free, so i thought i was home free,...


K3-Series

Raise and support the front end on jackstands.
  1. Remove the wheel.
  2. Remove the hub nut and washer. Insert a long drift or dowel through the vanes in the brake rotor to hold the rotor while loosening the nut.
  3. Using a puller, force the outer end of the axle shaft out of the hub. Remove the hub/rotor.
To install:
  1. Position the shaft in the hub and install the washer and hub nut. Leave the drift in the rotor vanes and tighten the hub nut to 173 ft. lbs. (235 Nm).
  2. Remove the drift.
  3. Install the wheel and lower the vehicle.

Jan 19, 2011 | Chevrolet K3500 Cars & Trucks

1 Answer

Show installation procedures for front brakes on 1993 jeep cherokee ,country model. size of nut that holds front brake rotor in place


Don't need a diagram for this... Leave the center nut alone! To replace the pads and remove the rotors, remove the two bolts that are on the inboard side of the calipers. Can't remember the size but there are small, somewhere around 10mm to 1/2". Once you get them off, remove the pads, then re-install the inner pad and using a large "c" clamp, drive the piston back into the caliper.
Once the caliper has been removed, it should just about fall off.
If not, use lots of wd40 or other solvent around where it meets the hub and into the wheel studs where they pass through the rotor. Use a heavy mallet or even a hammer to loosen them up.
Rotors are inexpensive and generally cutting them unless they are not very old is not recommended, so don't bother saving them unless it's absolutely necessary.
Be careful threading the caliper bolts back in. They must be in straight as they are very narrow and easily cross threaded.Always make sure that the slides they pass through are not frozen ane are properly lubed. Install is the reverse of removal.

Sep 06, 2010 | 1993 Jeep Cherokee Country

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

1 Answer

How do I remove and replace the front rotors on my 2004 V6 Ford Taurus


You must remove the brake caliper first then there should be a nut with cotter pin that holds it to the shaft some have a cotter pin some do not, but there should be a nut holding it on, remove nut slide rotor off, pack new bearings with grease then slide new rotor on, install nut and brake caliper, you may need to press caliper piston back in if it is too tight on the new rotor, use a c clamp to press piston back in.

Apr 11, 2010 | 2004 Ford Taurus

1 Answer

What is the socket size of the nut holding the front rotor on a 2005 toyota corolla? its not a hex nut but a 12 point socket?


the only things that are holding the rotor on is 1) the brake caliper which i believe has 2 14mm screws and 2) the brake caliper bracket which has 2 17mm screws holding it in place.once you remove these 2 parts,tap on the rotor( where the wheel goes bolted on )with a hammer and it should come off easily.if not spray some penetrant on the studs that hold the tire on, then tap on it some more and it should come off.hope this info helps.take care and good luck, manny

Apr 03, 2010 | 2005 Toyota Corolla

1 Answer

What is the size of the nut that holds the brake rotor on the 2002 honda accord


there is NO nut holding the rotors on, what you are looking at is the axel nut

Nov 06, 2009 | 2002 Honda Accord

2 Answers

Failed state inspection...front rotors need replaced


Remove the wheels, then on the back side of the rotor will be two bolts holding the caliper on. Remove them, then there will be two more bolts holding the caliper mounting bracket on, remove those, and the bracket. The rotors will slide off. If you have never had the brakes done there will be two metal washers holding the rotor on to the studs, cut them off with a chisel. They are only there to hold the rotors on during assembly line operations. Good Luck

Jun 03, 2009 | 2000 Chevrolet Suburban

Not finding what you are looking for?
1994 Chrysler Concorde Logo

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...