Question about 1983 Chevrolet Suburban

1 Answer

What should my ground wires be tied to in my 83 c-10?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Which ones? at the battery should have a small one to the body and the large one to the engine block.

Posted on Sep 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get a wiring diagram for a 96 Nissan fuel pump can't find one in my Chiltons


https://s26.postimg.org/davpnho3t/fuel_pump.jpg

Click on the link.
At the fuel pump, the black wire is ground. The other color wire is voltage.
If you know there is a ground problem, use a redundant ground, so far, it always works for me. Take a piece of wire, splice into the black wire, at a point where the wire is good, run the wire to clean metal part of chassis, Sometimes you can loosen a screw or something and tie-in there, then tighten it up.
As far as the factory chassis ground point, I don't know, at the moment. Just my opinion.

Sep 27, 2017 | Nissan Cars & Trucks

1 Answer

I had an elect ground fabricated &installed on RV Trans to correct a shifting problem. Now my 5500 Marquis won't start. No fire. Could the grounding kit be the culprit?


If the new ground wire is truly tied to a ground circuit it will not effect anything, unless the ground circuit tied into is a pulsing ground circuit. Example: the pulsed ground wire coming from a set of ignition points going to the coil or some other control unit that opens and closes a ground circuit when triggered.

Oct 13, 2016 | Cars & Trucks

1 Answer

Low Beam failure notification


Use a 12V test light to check. Clip the ground lead of the test light to the FRAME - not the ground wire of the socket. Probe the socket and wires. If no lights, follow the power wires back and test w/ probe until you find power. If it DOES light with the clip on the FRAME, place the test light clip on the 12V (+) terminal of the battery. and probe the GROUND wire of the socket back until it lights - this is the last place the GROUND connection is good. You should fix the break or cut the dead side of the wire and tie it to a good ground to get the headlight to work again.

Sep 28, 2015 | Cars & Trucks

1 Answer

Brake tail light strip on trunk is out. trouble shoot ? bulb on right side tail light is out. but can't find data on tail light strip of lights on trunk


Lets simply thing here. American Auto Manufacture use three wires set for it rear light assembly. One wire to the braking switch for both stop lights, one wire for the clearance light on both sides. Now if you look at the plug for taillight assemble there will three wires and didn't mention the third wire, it's ground. The two brake light uses one wire, then for on or clearance light uses one wire, and the ground uses one wire On old automobile normal the grounds any place on the body. But now the grounding points to make sure there isn't a faulty ground.

Turn signal light are a separate circuit as with the back up lights. I fairly sure your Caddy uses a Mylar strip with copper strips on it. Find were this copper strips are broken, scratch off the thin layer insulation and solder a jumper wire across the broken copper strip.

There will be a Central location where these light are tied together. Left brake light wire goes to the one wire from the brake switch under the dash, the right brake light goes to the same tied point to brake light switch under the dash. The Central wire point will be at one of the back lights. Just follow the colored wire. Now, each has two colors, one solid and one strip is colored with different colors. I hope this help you. GB stewbison

Aug 20, 2011 | 2001 Cadillac Seville

1 Answer

Changed senser computer says still the problem


The sensors under the hood had a ground problem i have tapped into the ground on sensor and ran a new ground back to battery negative [-] to stop that.
get a chilton's manual from orielly auto and it should give a wiring diagram and tell you the color of each wire from sensor one wire from each sensor goes to a common tie point which is the ground circuit hook into that wire from sensor and run a new wire to battery negative.

May 20, 2011 | Dodge Stratus Cars & Trucks

2 Answers

1997 Jeep wrangler rear emergency brake cable replaced and now brake light stays on


possible cable out of adjustment to loose.try forcing brake aplicator towards full off and see if it goes off. if so adjust switch or cable

Jun 26, 2010 | 1997 Jeep Wrangler

1 Answer

My son has a 1987 porsche 924 S. A mouse ate the


they share a ground thats why 2 are together

Aug 19, 2009 | 1987 Porsche 924

1 Answer

2003 Envoy wiper display problem


check wires if the is ground connection ,then check for wire miss connection. But then rain moisture can give effect on the radio and wiper if the is a grounded wires.

Jul 22, 2009 | 2003 GMC Envoy

1 Answer

12 volt system


The wires you have are white for common, 1 black for slide in, 1 black for slide out, and green for ground. Verify the direction that each of the black wires moves the slide before wiring. You will need a 3 position switch also.

Jul 03, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Installed radio in a dodge i turn on the headlights and the radio


Sounds like you wired the ground to your headlight dimmer wire. It's grounded until you turn the lights on, then it goes hot, thereby leaving your radio without a ground. Better see which wire you tied in to the headlight circuit. Be sure to check the wires you are connecting to on the vehicle's harness with the key off AND with the key on to make sure it's pos. or neg. when you want it to be.

Apr 17, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...