Question about Ford F-150

1 Answer

Where does the clutch fluid go in on a 1998 ford f-150 v6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,336 Answers

If your clutch is hydraulic, look next to the brake reservior..If the Master cylinder goes dry, you need to bleed it first....you can get an inexpensive m/c bleeding kit from aftermarket parts stores. Tons easier to do that way.

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you show me pi cure of clutch fluid reservoir and its location on 1998 ford escort


if you don't see any clutch fluid reservoir for the clutch, there are two possibilities: clutch master shares fluid reservoir with the brakes or clutch is using cable not hydraulic.

Mar 21, 2016 | Ford Cars & Trucks

1 Answer

I need to adjust my clutch on a 1998 ford zx2


Your vehicle has a hydraulic clutch, and there really is no "adjustment." Verify fluid level in the clutch fluid reservoir, and consider replacing clutch plates if you are experiencing slipping.

Apr 26, 2012 | 1998 Ford Escort

1 Answer

Clutch will not engage in my 1998 s10 help i need to get to work


Could be the slave cylinder or clutch plate. Check ur bell housing and see if your fluid level is low. You can put clutch fluid in the housing 3/4 of the way full. Pump your clutch a couple of times to get fluid in the lines. You can do this a couple of times, but after a week or so you NEED to replace your clutch. You can get'em at your local parts store for about $150. You need to have a mechanic replace your clutch because it involves removing your transmission. total cost about $400 Same thing happened to me twice in 2 yrs. Make sure you get a lifetime warranty. Hope this was helpful

Dec 09, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How do I repair clutch on 1998 ford f-150


buy new clutch pressure plate and throw out bearing also clutch line up tool ..refer to moter manuel at public library they wont let youtake it out so photocopy the pages you need.please rate this info.

Nov 27, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How to replace the oem clutch master cylinder on a 1988 ford f-150 ,,, where is it located on the truck?,,,


Removal:
1.From inside the cab, carefully pry the clutch master cylinder pushrod and retainer bushing from the pedal cross-shaft lever pin.
2. Disconnect and remove the interlock switch.
3. Remove as much fluid from reservoir as possible and place shop rags under the master cylinder to catch leaking fluid.
4. Disconnect hydraulic line from the master cylinder and plug lines and outlets to avoid contamination and excessive fluid loss.
5. Remove the two nuts retaining the clutch master cylinder.
6. Installation is the reverse of removal exept after installation, bled the system.

Feb 21, 2010 | 1988 Ford F 150

1 Answer

Yes my truck is 1998 ford f 150 4.2 an i have code po174






DTC code p0174 means "System too lean (Bank 1)"

Basically this means that an oxygen sensor in bank 2 detected a lean condition (too much oxygen in the exahust). On V6/V8/V10 engines



, Bank 2 is generally the side of the engine that doesn't have cylinder #1.

Jan 09, 2010 | 1999 Ford Windstar

1 Answer

Fitted new clutch and slave cylinder in 2.5 v6


crawl up under the dashboard & look where the clutch pedal rod goes through the firewall. look for traces of brake fluid at the rubber boot of the rod. a clutch master cylinder normally will leak to the inside of the vehicle & down the firewall when it fails. Replace as required & bleed clutch system using the bleeder valve that should be on the slave asy.

Oct 15, 2009 | 1998 Ford Contour

2 Answers

1997 Toyota Tacoma v6/4x4/manual: Clutch petal/Clutch


I currently have a 1998 Toyota Tacoma, and the clutch pedal does not return all the way. I know it is not the clutch, it is actually the spring located underneath the pedal. It is catching and not releasing after pushed.... Hope it helps.

Jun 19, 2009 | 1998 Toyota Tacoma

1 Answer

1998 ford escort clutch


There are 2 master cylinders on the escort, one for brakes, and the other for the clutch. You put the fluid in the master cylinder.

Apr 25, 2009 | 1998 Ford Escort

3 Answers

1998 tiburon 5 speed manuaL transmission


hey
try to use quaker state synthetic bleed multi vehicle atf

Jul 06, 2008 | Hyundai Motor 1999 Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...