Question about 2001 Mazda Protege

1 Answer

Does the passenger side cv axle of a 2001 mazada protege have to be press out because it does not want to come out the other side just slid out?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

No it should come out, sometimes you have to pry hard or shock it with a hammer to get it loose.

Posted on Sep 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the dipstick located on a 2001 Pontiac Sunfire for the transmission?


if its the 4 speed it don't have one it has check plug on the passenger side of transmission near cv axle and the fill plug is on top of transmission on drivers side youll see a red plug

Mar 08, 2015 | 2001 Pontiac Sunfire

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

1996 Mazda Protege cv axel removeal


Jack vehicle up use jackstand remove wheel seperate lower balljoint remove axle nut push thru pull strut assembly to side the use prybar between trany and axl n pop it loose n reverse

Dec 24, 2013 | 1995 Mazda Protege

2 Answers

01' Mitsubishi Eclipse cv axle removal passenger side


The passenger side has a inner and outer shaft and you would remove the axle nut and shaft from spindle then the center bracket and bearing (two bolts against engine block), sliding out the axle assembling at that point, or jerking it out, careful not to pull on the cv axle end but rather the jack, or inner, shaft. After removal, separate the middle by hanging upside down and taking a hammer to it, striking the inner shaft while turning around. Dont hit the dust shield or seals. Install in reverse order. Quick tip: you may get around removing ball joint by only removing both strut bolts, and possibly tie rod end bolt.

Mar 02, 2013 | 2001 Mitsubishi Eclipse Spyder

1 Answer

Vibration and whine when cold but abit when warm as well.


On the long cv axle you have a intermediate bearing..remove the clamp thats holding the bearing and spinn it and see if its bad..Should be the passenger side cv axle..The cv will check as good but the bearing can be bad

Nov 15, 2011 | 2001 Ford Focus

1 Answer

How do you change drive shaft on passengers side of car


CV Drive Axle Assembly -- not drive shaft

Have to loosen the lower ball joint & tie rod end,
to move spindle / steering knuckle out of the way,
to remove the axle

Jun 11, 2011 | 2001 Mitsubishi Galant

4 Answers

Clicking noise down by the front tires.


check your axles, for an open cv boot, this clicking is on straigth or turning, if turming to your rigth you hear noise to be louder on your left then your left axle is bad, do the same to your left and if noise exists then your rigth axle is bad.good luck

Feb 27, 2011 | 2003 Dodge Caravan

1 Answer

Changing cv axle on passenger side


axle nut, bottom ball joint. pop the axle out of the hub and let it hang. pry bar between the inner joint of the axle and tranny. a quick pry should pop it out

Apr 11, 2010 | 2001 Dodge Neon

2 Answers

Passenger side cv axle keeps breaking


Contact your local parts store. Some are the same and some are different. I believe that the passenger axle shaft is longer than the drivers side.

Apr 01, 2009 | 1988 Chrysler LeBaron

Not finding what you are looking for?
2001 Mazda Protege Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...