Question about 2002 Pontiac Grand Am

1 Answer

A metal pipe running from the radiator reservoir to the back of engine/manifold has a hole in it. I want to order a replacement but I dont know the name of the piece. Does anyone know the name of that piece?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

If you call the dealer and describe where the pipe is they will know what part you need.

Posted on Sep 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is there a freeze plug in the back of the block on a mazda mpv 3.0 liter engine?


do mean a frost plug not to sure bout that whats the year of your car it will most probs be a alloy pipe or metal pipe that runs under your manifold they tend to corrode a bit sometimes stopleak works but if hole is to big you will have to replace it hope this helps ya

Jun 23, 2014 | 1993 Mazda MPV

1 Answer

Engine stalls


The probable reason for engine stalling can be overheating.
The engine can be overheated due to many reasons and their remedies are listed below:
1. Insufficient coolant and water in radiator - Refill the coolant and water in reservoir
2. Radiator fan not working as needed - Loose connections, faulty fan
3. Damaged hoses and pipes - Replace hoses and pipes
4. Clogged pipes - Clean them

Jun 09, 2013 | Oldsmobile Cars & Trucks

1 Answer

2001 A4 thermostat location


Hello! Ignore my request regarding the engine size, The thermostat is well hidden..Standard labor to replace is 2.0 hours...Thermostat is part # 06B-121-111-G....
Step 1: Drain coolant...

Remove bottom belly pan... Remove coolant reservior tank cap... Remove plastic clip holding coolant sensor in place at lower radiator hose/pipe... With bucket/catch pan underneath, remove sensor and let coolant drain...


Step 2: Remove upper radiator hose...

Remove the small hose connecting the coolant reservoir to the upper radiator hose... Then remove the larger hose from the hard pipe running along the intake and from the radiator... You'll need to pop up (but not off) the metal clip holding the hose to the radiator, then firmly pull back..

Step 3: Remove intake hose (throttle body to inter-cooler)...

Remove driver's side headlight (not necessary but makes it a lot easier). Loosen clamp at each end and remove hose...

Step 4: Remove throttle body...

Remove electrical connector and 4 hex bolts (5mm)...

Step 5: Loosen serpentine belt and slip off of alternator...

Use a box-end or adjustable wrench on tensioner, pull to the right... Carefully slip belt off alternator (towards front of car). Allow to hang loose below...

Step 6: Remove alternator bolts...

Remove 4 bolts holding alternator to bracket...

Step 8: Remove vertical support piece from intake manifold to block...

Remove the two bolts holding the support piece (6mm hex)...

Step 9: Remove bolt from metal hose on thermostat; remove bolt from top of oil cooler...

This will allow you to move the hard pipe away from thermostat... Then wiggle it free from the pipe afterwards...

Bolt holding the hard pipe on the right, two bolts holding the thermostat to the block on the left...

Step 10: Remove upper and lower hoses from t-stat. Remove electrical connector on back side...

Step 11: Remove 2 bolts holding thermostat to block, and remove thermostat...See photo below...Guru...Saailer







10_23_2011_1_16_37_pm.jpg

Oct 23, 2011 | 2001 Audi A4

1 Answer

Diragram on how to change the water pump on a 1995 z24 cavalier 2.3


Check this procedure, according with the repair guide for...

2.3L and 2.4L Engines
(see Figure 9)
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  1. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  2. Carefully lower the vehicle.
  3. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  4. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  5. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

zjlimited_2033.jpg

Fig. 9: Water pump and cover mounting - 2.3L and 2.4L engines (click over image for zoom)

To install:

  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Hope helps; remember to rating this answer and leave a testimonial comment. Thank you for using FixYa.

Oct 13, 2011 | 1995 Chevrolet Cavalier

1 Answer

96 Crysler lhs over heating. I have replaced the radiator, water pump, timing is correct, all new hoses except heater core hoses, thermostat, cap to resevoir replaced, intake manifold gasket replaced, and...


I HAD THIS PROBLEM AND REPLACED THE THERMOSTAT, BUT THE TRICK IS TO OPEN THE BLEED SCREW ON THE THERMOSTAT HOUSING, AND FILL THE ENGINE WITH COOLENT UNTIL IT RUNS OUT OF THE BLEED SCREW. (CLOSE THE SCREW THEN) NOW THE ENGINE WILL HAVE THE CORRECT AMOUNT OF COOLANT.

I DIDN`T KNOW THE PROCEDURE FOR THIS AND MINE KEPT OVER HEATING UNTIL I LEARNED THIS TRICK.

Apr 15, 2011 | 1996 Chrysler LHS

1 Answer

How do I replace a water pump on a 1999 malibou with a quad 4?


Water Pump REMOVAL & INSTALLATION CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old. 2.4L Engine
  1. Disconnect the negative battery cable
  2. Detach the Oxygen (O2) sensor electrical connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for a more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break the manifold-to-exhaust pipe spring loaded bolts loose using a 13mm box wrench.
  8. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  9. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  10. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt. NOTE: DO NOT rotate the flex coupling more than 4°or damage may occur.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  12. Remove the radiator outlet pipe from the oil pan and transaxle. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  13. Carefully lower the vehicle.
  14. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  15. Remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  16. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces. Fig. 1: Water pump and cover mounting - 2.4L engine 87953070.gif
    To install:
  17. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  18. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  19. Lubricate the radiator outlet pipe O-ring with antifreeze and slide the pipe onto the water pump cover. Install the bolts finger-tight.
  20. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts:19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly: 106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first: 19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover: 125 inch lbs. (14 Nm).
  21. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  22. Raise and safely support the vehicle.
  23. Index the exhaust manifold bolts into the exhaust pipe flange.
  24. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  25. Connect the radiator outlet pipe to the transaxle and oil pan.
  26. Install the timing chain tensioner and front cover.
  27. Install the lower heat shield.
  28. Carefully lower the vehicle.
  29. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  30. Tighten the manifold-to-exhaust pipe nuts to specification.
  31. Install the upper heat shield.
  32. Attach the oxygen sensor connector.
  33. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  34. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine OFF.
  35. Once the vehicle has cooled, recheck the coolant level, then install the radiator cap.

Oct 26, 2010 | 1999 Chevrolet Malibu

2 Answers

How to replace water pump on 97 pontiac sunfire 2.4


PLEASE DON'T FORGET TO RATE! THANKS! 2.3L & 2.4L Engines
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.
  1. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  2. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  3. Carefully lower the vehicle.
  4. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  5. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  6. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

01add58.gif
Water pump and cover mounting-2.3L and 2.4L engines

To install:
  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Sep 13, 2010 | Pontiac Sunfire Cars & Trucks

2 Answers

I have a 2000 pontiac grand prix gtp with supercharger. I have oil in coolant reservoir, I am not getting the white steam from exhaust pipes. car runs fine. not overheating. I checked the oil dipstick and...


The reason for this is because your trans cooler(which is built into the radiator itself) has failed and burst causing trans fluid to contaminate the cooling system.The fix for this is to remove and replace the radiator with a new one and then flush your cooling system to remove all trans fluid.I hope I could help!!! Any other questions please get back to me and rate me accordingly.

Apr 10, 2010 | 2000 Pontiac Grand Prix

1 Answer

WHERE THE WATER PUMP IS LOCATED on a 2.3 liter 4 cylinder quad hoc


it is driven off the timing chain, here is how you replace it
2.3L And 2.4L OHC Engines
  • Disconnect the oxygen sensor harness connector
  • Raise the vehicle and support it securely on jackstands
  • Remove the exhaust manifold brace and loosen the exhaust manifold bolts
  • Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine
  • Remove the exhaust manifold pipe from the exhaust manifold
  • Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging
  • Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head
  • Remove the timing chain cover from the engine
  • Remove the timing chain tensioner
  • Remove the water pump cover bolts from the engine block and the timing chain housing
  • Remove the water pump bolts and separate the assembly from the housing


Dec 01, 2009 | 1994 Pontiac Grand Am

1 Answer

Replacing the water pump


2.4L Engine
  1. Disconnect the negative battery cable
  2. Detach the Oxygen (O2) sensor electrical connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for a more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break the manifold-to-exhaust pipe spring loaded bolts loose using a 13mm box wrench.
  8. Raise and safely support the vehicle.

NOTE It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.

NOTE DO NOT rotate the flex coupling more than 4° or damage may occur.
  1. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  2. Remove the radiator outlet pipe from the oil pan and transaxle. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  3. Carefully lower the vehicle.
  4. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  5. Remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  6. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.
87953070.gif Water pump and cover mounting—2.4L engine
Click to Enlarge
To install:
  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slide the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts:19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly: 106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first: 19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover: 125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan.
  10. Install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine OFF.
  19. Once the vehicle has cooled, recheck the coolant level, then install the radiator cap.

3.1L Engine
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Loosen, but do not remove, the water pump pulley bolts.
  4. Remove the serpentine belt.
  5. Unfasten the water pump pulley bolts, then remove the pulley.
  6. Remove the five water pump mounting bolts, then remove the water pump.
To install:
86883115.gif View of the water pump mounting and bolt tightening specifications—3.1L engine shown
Click to Enlarge
  1. Clean all the gasket surfaces completely.
  2. Apply a thin bead of sealer around the outside edge of the water pump along the gasket sealing area, then install the gasket onto the water pump.
  3. Position the water pump on the engine, then tighten the water pump mounting bolts to 89 inch lbs. (10 Nm).
  4. Install the water pump pulley and finger-tighten the pulley bolts.
  5. Install the serpentine belt.
  6. Tighten the water pump pulley bolts to 18 ft. lbs. (25 Nm).
  7. Fill the cooling system.
  8. Connect the negative battery cable, then start the engine. Let the engine run until it reaches normal operating temperature, then check for leaks and coolant level. Add coolant, if necessary, then turn the engine OFF.

Aug 20, 2009 | 1997 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...