Question about 1986 Isuzu Pickup

1 Answer

Need sleeve/collar that holds throw out bearing on goes on trans axle of 1986 izuzu pickup

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 22,095 Answers

Try ordering one from a dealer

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REMOVEING DIFFERENTIAL ON A 1999 300M FRONT WHEEL DRIVE


The diff is part of the trans axle automatic transmission assembly and is not a separate part that can be removed.

Oct 10, 2012 | Cars & Trucks

1 Answer

A friend wants me to install a throw out bearing into his 2wd '86 Isuzu pick-up. Are there any common problems i may encounter? My manual trans experience is very little.


The 2wd is pretty straight forward but I would be careful of his diagnosis. A lot of people think that the noise from the input shaft bearing is being caused by the throw out bearing. Be sure the noise is when you have your foot pushed down on the clutch. If the noise is present when your foot is off the clutch and loudest while driving in first gear, then the problem is with a bearing inside the transmission and it will have to be taken apart.

Mar 28, 2011 | 1986 Isuzu Pickup

1 Answer

I've lost thecollar/sleeve that goes on the trans axle and holds the throw out bearing in on my 1986 izuzu pup pickup I can't find part anywhere junkyards etc... any suggestions?


we have no parts resources at fixya, I suggest you try a used part locating site, here is a link to one I use that has found what i need in the past many times

http://www.uneedapart.com/used-isuzu-parts.php

Sep 02, 2010 | 1994 Isuzu Trooper

1 Answer

1986 chevy s10 trying to remove center bearing on


theres a collar on the youk.remove it and tap it out its splits the tow pieces of drive shaft.use alot of pb blaster and make sure you grease the youk theres a grease fitting there

Mar 27, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

2002 f250 4wd, 7.3 psd. noticed today while


the wheel bearing is the cause, it has a support bearing that hold the axle in place.

Oct 04, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

CV up and down movement while in transaxle.


You can go to (autozone.com) & sign up for free & get access to parts prices & repair guides, that may just have what you need for info. Once signed up just pick your vehicle & go to repair guides & click on "drive train". Good Luck

Jul 03, 2009 | 1995 Dodge Caravan

1 Answer

Rear axle bearings


There are 4 bolts for each rear axle. They are located behind the rear brake drums. Remove e-brake cable from rear drum and take off brake line.(carefully). I recomend draining and changing your rear differential fluid too, because if the fluid by run out of axle housing. also you should replace the seals for the axles of if you are changing the bearings. When you are done don't forget to bleed your brakes, and hooking up e-brake cable. I hope this answers your question.

Jan 28, 2009 | 1986 Toyota Pickup 4WD

3 Answers

Front oil seal


They are right. The sleeve will seal against the crank seal. The ridges are what is letting the seal leak. I install sleeves quite often on older models, the success rate is pretty high.

Jan 13, 2009 | 1986 Toyota Pickup 4WD

1 Answer

Reinstalation of driver-side axle into manual trans.94 saturn


no trick sometimes the splines are tight. also check the ring clip to make sure it is in place this is what snaps in to hold axle in trany. you can use a block of wood and a sledge ham to bang end of axle into trany. just hold tight so c.v. joint does not bent while banging it.

Jan 06, 2009 | 1994 Saturn Sl

1 Answer

Rear axle bearings need replaceing I hear grinding


Go to Jeep and buy a bearings, seals, and collar. The bearing is held in place on the axle by a keeper collar. This must be cut off to get the old bearing and seal off. Use a wizz wheel to cut it and then whack it with a chisle

To get the axle out. Remove rear diff cover, and wheel and start taking apart. It's not a terrible job, but if you aren't very mechanically inclined, take it to a shop. Make sure you use the correct fluid in the differential.

Nov 18, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...