Question about 1995 Chevrolet Camaro

1 Answer

Need plans on how to remove drivers side door panel to change out Electric window motor.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 450 Answers

Go to a auto parts store and buy a special tool to remove the locks that hold the panel in place

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My passenger side electric window stopped working on my 1991gmc sierra 1500. The passenger side switch panel don't work for the window but works for the lock. Driver side master switch doesn't work for the...


The odds of both switches going bad at the same time is high, remove the door panel and tap on the window motor with a hammer, while trying the switches. I may have jammed up. Ground a test light and check the motor connection, while trying the switch, power will show on either side depending on if it turning up or down

Mar 19, 2015 | Cars & Trucks

1 Answer

BMW rear left hand side tail light and flasher not working also drivers window not working


The electric window could either be the fuse,switch, or window regulator motor at fault..Sometimes the window motor electric plug can vibrate loose or become loose from door slamming..Also the switch can become loose as well or contamination if you are lucky..You will have to remove door panel to inspect these components..and fuse panel..The light could be a faulty bulb..Check and replace bulb..before involving the signal indicator switch lever...If bulb is at fault go ahead and change bulbs at both rear sides..Do not try to repair signal switch because of air bag..If you can hold down on the turn signal switch and it works the switch is at fault...

Feb 21, 2015 | 2008 BMW 525i Sport

2 Answers

How do i change the drivers side window motor an an 05 kia sedona


You have to remove the inner door panel to
access the window regulator

You remove the regulator & then the motor from it

You Tube Video will provide a visual of several
similar window motor replacement jobs

Go there-- enter your car,question ,details,etc--- then move
around the site to watch various things

Dec 09, 2012 | 2005 Kia Sedona

1 Answer

Drivers side window switch clicking


Larry if the window does not go up or down its likely that the gear driven assembly or the motor on your electric window for the drivers door is bad. You will need to disassemble the door by removing the door panel to gain access to the electric motor. Hope this helps you will want to gain access to a service manual from a local parts store to help you with this venture. Good Luck

Nov 28, 2011 | 2002 Kia Sedona

2 Answers

I need help with replacing the driver side window in a 2003 ford f-150,four door super crew cab truck.


Removal & Installation
Motor - Front Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch
  3. Remove the front door trim panel and watershield.
  4. Tape the window in the full UP position.
  5. Disconnect the window motor electrical connector.
    NOTE Support the window motor while removing the window motor retaining screws.
  6. Remove the window motor bolts and remove the motor.
  7. To install, reverse the removal procedure.
Rear Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the rear door trim panel and the rear door trim watershield.
  4. Remove the door speakers.
  5. Tape the window glass in the full UP position.
  6. Disconnect the window regulator electric drive.
  7. Position the connector for the window regulator electric drive inside of the door.
  8. Remove the bolts.
  9. Separate the window regulator electric drive from the rear door window regulator.
  10. Remove the window regulator electric drive from the door.
  11. To install, reverse the removal procedure.

Motor & Regulator

3d4a07e.jpg

Fig. Front Door Trim Panel

7932e42.jpg


Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows

506866e.jpg

Fig. Window regulator arm nuts


db15984.jpg

Fig. Window regulator bolts

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the door trim panel.
  4. Remove the door speaker.
  5. Remove the door watershield.
    NOTE Do not remove the window glass from the door.
  6. Remove the window glass from the window regulator.
  7. Tape the window glass in the full UP position.
  8. Disconnect the window motor electrical connector (power windows only).
  9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
  10. Loosen the bolts and remove the window regulator.
  11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

Nov 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

How to chang out the front drivers side electric window motor


you need to remove the door panel and with the window up and wedged so it dont come down on you remove the power connections to it and drill out the rivets and remove the old motor reassemble new motor and either rivet back in or bolts are supplied make sure the bolt faces out so not to interfere with the glass

Sep 07, 2009 | 1994 Buick Roadmaster

1 Answer

My drivers side electric window stop working 2002 ford sport trac. how do you change the motor


To remove the door panel, phillips head door screws should be removed, and the panel should slide up. Next, unbolt the window from the regulator and remove the window from the door. Then unbolt the regulator. The regulator and the motor have to be removed together. The motor will be mounted to the door on the inside. There should be three screws or nuts (10mm) holding the motor in. Remove motor and regulator. Reverse to reinstall.

Jul 11, 2009 | 2002 Ford Explorer Sport Trac

1 Answer

Drivers side electric window does not work


Remove the door panel and disconnect the motor from the window, but leave it plugged in. See if the motor works. If it does you should grease the tracks on the window. If the motor does not work then you should replace the motor. The motor will probably get hot when you try working it.

Jan 23, 2009 | 2005 Nissan Xterra

1 Answer

95 blazer, front driver window motor broken need to get window up


When removing the door panel, you need to remove all of the screws first. Then pull the door panel off. There should be screws around the edges or the door panel, and 1-2 screw on the door handle(on the inside). Then pop the door panel off, if the blazer has electric windows and locks you have to disconect them first, if it doesnt have power locks and windows, you have to take the window crank off,there should be a screw in the center of that. Unscrew the door lock and pull up. If it doesnt have them locks then you have to disconect it from inside the door panel

Nov 30, 2008 | 1995 Chevrolet Blazer

2 Answers

1990 buick centruty, driver door schematic (window regulator)


The first thing you need to do before buying any parts is to remove the door panel and find out exactly what is wrong, the motor is a gear reduction unit and even if the motor works it may still not drive the output gear. The door panel is held on by screws and hidden clips, pop off any panels or light fixtures on the door trim, under those you will find the hidden retainer screws, then gently pull door panel at edges to disengage feather style snaps.

Aug 26, 2008 | 1990 Buick Century

Not finding what you are looking for?
1995 Chevrolet Camaro Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...