Question about Jeep Grand Cherokee

1 Answer

My 2004 Jeep Cherokee blower motor is intermittent. I can make it work by moving the electrical connector at the resistor/detector?? installed in the main flow path beneath the glove compartment.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,129 Answers

You have found the fault with this inspection,the switch or the connector or the rheostat is faulty.
So remove of the switch and look for loose connection or faulty connection. since this is workingg the fan is alright and it is only in the selection. use a good light an dlook under the dash .
Go on to find this out.

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove heater blower motor?


1998 ATC Jeep Grand Cherokee Blower Resistor connector ...

? 0:55
www.youtube.com/watch?v=sDFLuenx9aw
Nov 14, 2012 - Uploaded by Freedomautomotive1
1998 ATC Jeep Grand Cherokee Blower Resistor connector Repair Kit (RARE 1/2 Year) ... How to Fix a Chrysler Blower FanThat Only Works on High - Duration: 16:51. ... JEEP2001 FIXING THE HEATER BLOWER CONTROL. ... Jeep Grand CherokeeCenter and Lower Dash Removal - Auto Repair Series ...

Sep 30, 2015 | 1998 Jeep Grand Cherokee

1 Answer

Blower motor only works on high for 2004 jeep grand cherokee what is the fix ?


This is caused by a defective blower motor speed control resistor. The resistor is located next to the blower motor with one end going into the air ducting and the other sticks out with an electrical connector on it.

Jun 10, 2012 | 2004 Jeep Grand Cherokee

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

3 Answers

Blower motor resistor, where is it located/


It will be up under the dash on the passenger side near the blower motor. It will have 5 or six wires in its connector

Nov 10, 2010 | 2000 Jeep Grand Cherokee

1 Answer

2005 Jeep Grand Cherokee. Htr/AC fan switch only functions @ highest speed. At lower speed settings I can hear doors opening and closing---but not air.


replace the blower motor resistor. It controls the fan speeds. It defaults to high speed only when it fails.

How to replace the blower motor resistor block: Caution: Stay clear of the blower motor and resistor block (Hot). Do not operate the blower motor with the resistor block removed. 1. Disconnect and isolate the battery negative cable.
2. Remove the glove box from the instrument panel.
3. Pull out the lock on the blower motor resistor wire harness connector to unlock the connector latch.
4. Depress the latch on the blower motor resistor wire harness connector and disconnect the connector from the resistor.
5. Remove the two screws that secure the blower motor resistor block to the HVAC housing.
6. Remove the resistor block from the HVAC housing. Installation:
1. Position the blower motor resistor block into the HVAC housing.
2. Install the two screws that secure the resistor block to the HVAC housing. Tighten the screws to 2.2 Nm (20 in. lbs.)
3. Connect the wire harness connector to the resistor block.
4. Push in the lock on the blower motor resistor wire harness connecgtor to lock the connector latch.
5. Install the glove box.
6. Reconnect the battery negative cable.
7. Have a nice day!

Oct 11, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

Where is the blower motor resistor located in the 1997 jeep grand cherokee larado?


IT IS UNDER THE GLOVE BOX NEXT TO THE BLOWER MOTOR.IT WILL HAVE 2 DIFFERENT ELECTRICAL CONNECTOR

May 07, 2009 | 1997 Jeep Grand Cherokee

2 Answers

Heater Air Motor not working on 2000 Jeep Grand Cherokee all the controles seem to work they light up and change when you turn the knob but no motor movment tried looking for the fuse but could not find


First off, it's called the blower motor. Check in your manual for the fuse for that. If the fuse is good, it could either be a bad blower motor or blower motor resistor.

Sep 10, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...