Question about 2000 Mazda B-Series

Open Question

Need schematic to change thermostat on Mazda B2500

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75797 Answers

SOURCE: Need fuse diagram for mazda b2500

go to the link below and choose the 1998 ford ranger as the truck, they are the same, then follow the link to ford site and download the 1998 ranger owners manual, the fuse diagrams are in there
http://www.edmunds.com/ownership/howto/articles/120189/article.html

Posted on Sep 16, 2009

dsakrison1
  • 65 Answers

SOURCE: 98 mazda b2500-my turning signal/hazard lights no longer work

You need to replace the flasher module, this is the module that controls the "Blinking" function of the lights, its a mostly a common part that you can get at any auto parts store for less than 10 bucks and is located in the Fuse panel under the dash, its round in shape in one corner of the panel. mostly they are green in color.

Posted on Oct 02, 2009

  • 1596 Answers

SOURCE: Can't locate the thermostat on my 1998 Mazda B2500

Look Straight Dowd from CENTER form Radiator side you will see the Housing

Posted on Dec 09, 2009

  • 33 Answers

SOURCE: i have a 98 b2500 mazda pickup

Loss of Power, too?

Burnt Valve! My guess - cylinder 3.

Posted on Apr 08, 2010

  • 365 Answers

SOURCE: How to change front disc brake pads on 2000 Mazda

jack up car, remove the road wheels, at the rear of the caliper you will have 2 or 3 bolts holding the caliper onto the stub axle, remove the bolts and remove the caliper, remove the outer pad, leave the inner pad in place and use a "G" clamp to compress the brake piston until it has bottomed, if this is not done the new pads will not fit back over the rotor as the piston is too far out and the new pads are thicker than the old ones.
place the new pads in the caliper and fit over the rotor, replace the 2 or 3 bolts that hold the caliper in place, replace the road wheel, tighten the nuts and lower the car to the ground, pump the brake pedal to see if you have brakes, if you do have brakes take it for a test drive away from any traffic if possible

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is thermostat located on a Mazda B2500 2008 model


motor end of the upper radiator hose , in a housing .

Dec 01, 2016 | Mazda Cars & Trucks

1 Answer

Where's the thermostat to my 98 Mazda truck 5speed b2500


Follow the top hose from the rad to the engine block, there should be a gard housing at the end of it, ....the housing should attach to the engine bloxk with a few bolts, the thermostat should be under that.

Jul 19, 2015 | Mazda Cars & Trucks

1 Answer

1998 mazda b2500


maybe you thermostat is not working properly. if the water from the hose is flowing through your cooling system freely that tells me your thermostat is wide open

Jan 20, 2014 | Mazda B-Series Truck Cars & Trucks

1 Answer

Bettyboop9288@yahoo.comcannot find location of my thermostat on my 98 mazda b2500 .i need a diagram so i can replace it


most of the time if you just follow the top radiator hose to where it connects at the top of the engine there will be a housing there that the hose connect to and normally if you unbolt that housing from the engine the thermostat is right there. good luck

Nov 10, 2010 | 1998 Mazda Pickup

1 Answer

Hi how do I go about changing my thermostat on my


Follow the upper radiator hose to the engine block. The hose goes directly to the thermostat housing. It has 3 bolts to remove. Just place a rag underneath to catch the little tiny bit of coolant that will leak out. Then pull out the thermostat, place the new one in and the gasket if it has one. Not all of them have one, put the housing and 3 bolts back in and you are good to go.

Jul 15, 2010 | Cars & Trucks

1 Answer

Need to know if 1999 mazda b2500 has a transponder


if the head of the key is made of black plastic covering it is

Feb 06, 2010 | 1999 Mazda Pickup

Not finding what you are looking for?
2000 Mazda B-Series Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...