Question about 1997 Ford Crown Victoria

1 Answer

Where would the 02 sensores for a 1997 ford crown victoia be located on the vehicle

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 116 Answers

The two pre-cat sensors are the exhaust pipe(s) just after the manifolds, the two downstream sensors are between the first and second cat(s) on the H-pipe.

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I had a 1997 Ford Crown Victoria with An H9 rear axle code. I want to know what rear axle code is comparable to the H9 for a Mercury Grand Marquis?


reading forums on this reveals that the h9 is a 3.55 limited slip diff mainly used in f150 fords. However all that is immaterial as what you are looking for is a diff centre that is 3.55 ratio that will fit in your housing . The same housing will use the both LSD and normal diffs as the LSD was an option offered for off road vehicles or vehicles operating in bad road conditions

Sep 18, 2014 | 1997 Ford Crown Victoria

1 Answer

2006 crown vic, What are the symptoms of bad transmission range sensor


not shifting --- slow shifting --- missing gear changes --- no OD or reverse or slow shifting to them. Have a pressure test done on the transmission to check for internal damage and have the bands and clutch packs adjusted . Run fault codes if this is available on your vehicle.

Jan 03, 2014 | 1997 Ford Crown Victoria

1 Answer

02 Sensor


what do you mean by O2 sensor oxygen sensor? is located on the exh. pipe

Jun 17, 2013 | Ford Cars & Trucks

1 Answer

Im trying to find out on my 1998 ford contour svt 2.5 .where is the 02 sensors located.im actually looking for the downstream 02 sensor which i think its the bank 1 sensor 2.i see 2 from underneath


It's in the center, rear engine area, mounted in the exhaust manifold. Kind of a pain to get at, but doable. It's easier if you take the oil filter off.


5848acf4-311c-43ce-99b9-51e3547b4518.jpg

Nov 15, 2012 | 1997 Ford Contour

2 Answers

WHERE IS THE OXYGEN CENSOR ON A 1997 GRAND MARQUIS


O2 sensors are located in the exhaust manifold near the Catalytic converter.
Some cars have the 02 sensor before the catalytic converter, some behind, and some before and after.

Simply locate the "bung" that contains the O2 sensor, and you will see the sensor connected to wires.
This is the best way to locate them.

-Jackson
http://urbanscooters.com/

Oct 11, 2010 | 1997 Mercury Grand Marquis

1 Answer

Where is the location of no. of cylinder on crown


2004 Ford Crown Victoria 4.6 liter V-8 VIN "W"

a39c7f2.gif

Hope helps (remember rated this).

Jul 19, 2010 | 1997 Ford Crown Victoria

1 Answer

1997 Crown Victoria: 92 crown victoria get no spark...


Attempt to change all of the spark plug wiring and spark plugs. Then start the vehicle.

May 18, 2010 | 1997 Ford Crown Victoria

1 Answer

Need help finding the ignition module on a 97 ford crown victoria


There is no ignition module. The ignition coils are controlled directly by the Powertrain control module (computer) located inside the vehicle above the drivers left foot and connected to the engine wiring harness thru the firewall

Apr 06, 2010 | 1997 Ford Crown Victoria

Not finding what you are looking for?
1997 Ford Crown Victoria Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...