a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Sunroof Description and Operation (One Connector System)
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.
Your best bet , take it to a qualified repair shop or buick dealer .
Check the RAP fuse in the rear fuse box , this fuse powers the sunroof control module !
Fuse Block - Rear , Left rear of the passenger compartment, under the rear seat .
The sunroof module contains the logic for the opening and the closing of the sunroof. The sunroof motor assembly contains the reversible DC drive motor, the gear train, and the limit switch.
The sunroof module determines the sunroof motor direction based on inputs received from the overhead console sunroof switches. When the ignition switch is in the ON position or when retained accessory power (RAP) is active, voltage is applied to the sunroof module via the RAP relay. For a description and operation of the RAP system, refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power. The sunroof module controls the sunroof motor direction by changing the polarity of the applied voltage. The sunroof module remembers the sunroof position whenever the ignition switch is turned to the OFF position. The limit switch is used as an input to the sunroof module to indicate that the glass is fully closed, or in the comfort stop positions. The limit switch is grounded when the sunroof glass is in the fully closed or comfort stop positions, otherwise it is open.
The SLIDE CLOSE mode is initiated by moving and holding the sunroof slide switch (ROOF) forward. This applies a ground provided from the sunroof limit switch low reference circuit to the sunroof switch close vent signal input of the sunroof module. The sunroof module controls voltage to the control circuits of the sunroof motor. The sunroof motor will run until the limit switch contacts are closed. The closing of the limit switch will apply the sunroof limit switch low reference circuit to the sunroof limit switch soft stop signal circuit to the sunroof module, indicating the flush closed position has been reached. As the sunroof is approaching the close position the sunroof glass will force the wind deflector downward.
You need to have a factory scan tool hooked up an have it checked for DTC'S in the sunroof control module ! a code reader will not do this , a code reader will only check the engine codes for OBD 2 . Important: The following must be completed before using the symptom tables.
Perform Diagnostic System Check - Power Sunroof in order to verify that all of the following are true:
No DTCs are set.
The control modules can communicate via the serial data link.
Review the system operation in order to familiarize yourself with the system functions. Refer to Sunroof Description and Operation
have you checked the fuse for the sunroof motor fuse bo lower dash drivers side cover/lid should give list , the owners manual should tell you how to manually close roof if fuse is ok ,have included a link to a hyundai forum as these sites have lots of advice and info Hyundai Forums Hyundai Forum
Probably too late for you, but I just "fixed" the stuck sunroof. I didn't want to spend anything and didn't care if it worked, I only wanted it closed. By taking the motor off, I was able to easily push the sunroof closed, then secured the motor back in place and it keeps the sunroof locked, closed. I tested the seal by running water over it, and all is good. Liquid Roof Coatings Application and Uses BuyLiquidRoof
could be a few things, firstly the fuse for the sunroof, secondly some have a small relay next to the motor near the sunroof. if the switch for the sunroof is on the roof pop it out of the trim or unscre it if it is fixed with screws, check the wiring looks right if still wont close then simply unplug the wires off the back of the switch, tel me how many wires you have and the colours, you can attach 2 toghether and this will close the sunroof if the switch is the part that has failed, Always check fuses first!
Check the fuse in the fuse box. If that is good then you might want to look into getting a new sunroof motor. The gears in the motor are plastic so one of them may have some broken or missing teeth. If you can hear the motor run then replace the motor. Also, maybe the switch is bad. Check all of the connections and make sure that they are seated right.
Some customers may comment that the sunroof will no longer respond to the control switch while in a vented, partially opened, or fully opened position.
A software issue with the sunroof control module may cause the sunroof control module to incorrectly indicate a "closed" position, which may result in no power to the sunroof motor.
Verify the customer concern. If a condition is present, replace the sunroof control module with a new sunroof control module, P/N 15847643. Refer to the Service Procedure in this bulletin.
Verify the customer concern by opening and closing the sunroof.
If the sunroof will not open , check the power windows.
If the power windows are also inoperative, check the fuse. If the fuse has opened, refer to Corporate Bulletin Number 05-08-64-004 to install 30A circuit breaker.
If the power windows are fully functional, refer to "Power Sunroof Inoperative" diagnostics (SI Document ID# 1392967) in the Body section of the 2005 Chevrolet Equinox or Saturn VUE Service Manual.
If the sunroof will open (or is already open), but will not close , proceed to Step 2.
Replace the sunroof control module. Refer to "Sunroof Control Module Replacement" procedure in the Body section of the 2005 Chevrolet Equinox Service Manual (SI Document ID# 1196049) or Saturn VUE Service Manual (SI Document ID# 1710479).
Open and close the sunroof in order to confirm that the customer concern has been resolved.
you can open and close you sunroof "manually" remove the plastic cover next to your sunroof and dome light buttons (above your rearview mirror) there is an allen wrench stored inside... insert the wrench into the corresponding hole and you can close or open you sunroof by turning the wrench
I have the same problem on my car and took it to the dealership to get it checked, they said that the 2001 is the one of the only years that doesn't have a manual close function. They told me my motor was completely dead and the only way to close it is to replace the motor. My only problem is knowing where the motor is. I would have yours checked if you haven't already.