Question about 2006 Mitsubishi Eclipse

1 Answer

Engine light is on, gear selector light is flashing, car is reving weird between gears.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,297 Answers

Sounds like a defective OSS
seek assistance from your local parts store
they will pull codes for free

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car shakes in reverse and engine light is blinking, gears will not change gets stuck in 2nd or 3rd gear


When the check engine light flashes it means DONT RUN IT or you will damage the engine. There are codes that your mechanic pulled from the computer, WHAT ARE THOSE CODES?

Apr 29, 2013 | 2002 Hyundai Accent

1 Answer

1.Can a flashing hold light/faulty mass air flow sensor burn the clutches in a transmission? 2.if vehicle reves out after changing into second gear and transmission is rebuilt and problem still persist...


The ecm would not cause this, it sounds like someone did a poor rebuild, if the engining is reving and the car doesnt what to go then the clutches may be bad, a mass are flow would not cause a trany to go bad, the flashing hold light is a problem but should not be happening after the trany was just rebuilt, something is not right here, the trany was just rebuilt and now the hold light flashes and the motor rev going into 2nd gear, that trany has problems a bad ecm wouuldnt cause this slipping reving problem you are having , i would have a trany shop check to see if that trany was really rebuit.

Jan 12, 2011 | 1998 Subaru Forester

1 Answer

Transmission was acting weird while driving.... slamming into gears and then I noticed OD light flashing on gear selector.....~200 miles later the check engine light came on. P0500 code found at shop and...


This is a common problem with Broncos, The dealer can solve this by Re-Flashing the ECM, Engine Control Module, or at worst, Re-Programming the ECM. Auto Plaza Ford in St. Louis quoted $129.00 for the diagnosis and Re-Flash and $109.00 additional if it needed a complete Re-Program. The Problem will come back if not fixed.

Aug 02, 2010 | 1996 Ford Bronco

1 Answer

All the gear indicators PRN321 on th dash of my 87 Tornado are flashing, what gives?


The gear selector switch is either out of adjustment or it is bad. Loosen the two bolts holding the gear selector in place and turn it slightly to see if the display stops flashing. You will have to manually shift the transmission lever at the switch into neutral, and then turn the switch until the display says neutral. Tighten the bolts and then check all gears. It's also possible the shift cable could also be out of adjustment. Does the display change if you simply wiggle the gear selector lever?

Dec 02, 2009 | 1987 Oldsmobile Toronado

1 Answer

Gearshift selector problem


The gear selector switch is either out of adjustment or it is bad. Loosen the two bolts holding the gear selector in place and turn it slightly to see if the display stops flashing. You will have to manually shift the transmission lever at the switch into neutral, and then turn the switch until the display says neutral. Tighten the bolts and then check all gears. It's also possible the shift cable could also be out of adjustment. Does the display change if you simply wiggle the gear selector lever?

Oct 22, 2009 | 1988 Oldsmobile Toronado

1 Answer

94 Chevy Silverado 4L60E Trans. Lost all drive gears


Internal gear selector in Tranny is shot...try replacing with used..or get to a tranny shop..Good luck

Jun 16, 2009 | 1994 Chevrolet C1500

1 Answer

2004 trailblazer going in and out of gear


Suspect transmission has failed. Recommend further diagnosis as transmission rebuilds are very spendy.

Apr 10, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
2006 Mitsubishi Eclipse Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...