Question about Hyundai Elantra

1 Answer

98 elantra j2 1.6gl need to remove inner door panels. Have removed all screws but stuck with window winder handle. how od i remove this.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

On the chrome part, you have a plastic trim,prise it off at the thickest part and pull towards you.

Posted on Sep 02, 2010

  • dhirajr Sep 02, 2010

    sorry guru no chrome part, the winder is full brown solid plastic unit. the normal surclip that sits on the inside shaft is not present on this model.

  • geoff hunter Sep 02, 2010

    has it got a pin through the shaft then???push the door trim in slightly...

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the inner door panel 1990 dodge dynasty


Remove handle ,window winder if not electric,remove arm rest screws prize door trim off carefully using a flat blade or screw driver.window winder is held on with a horse shoe clip which can be removed with a piece of wire with a hook in the end.

Oct 04, 2015 | Dodge Cars & Trucks

1 Answer

Remove internal door lining drivers side to get to internal power window winder


Usually two or three screws along bottom edge one behind all handles. Remove screws carefully pry panel loose away from door using caution not to damage the clips holding panel on might need a tool for this. I removed enough not to need tool. Have to pry all the way around panel, lift panel up off door by sliding it towards top of door. Disconnected all wire connections, to disconnect handle remove clip panel is off

Apr 03, 2015 | 2009 Hyundai i30 cw

1 Answer

I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Feb 02, 2012 | 2000 Dodge Caravan

1 Answer

Want to replace broken outside door handle on 1993 corolla


  • remove screw on inner door release cover
  • pull latch out-slide and pull
  • remove inner linkage
  • remove window winder or switch
  • remove arm rest (2 screws)
  • undo screws and clips and remove trim
  • wind window up
  • from inside the door remove operating linkages-
  • two 10mm screws hold the outside handle
  • on some cars you might have to undo the latch to make room to undo the two screws for the handle
I know it is brief but it will give you an idea of what needs to be done .hope this helps.
should take 30mins

Sep 14, 2011 | 1993 Toyota Corolla

1 Answer

How do you remove the inside door panel backseat right side of a mercury grand marque 1996


Door Panels REMOVAL & INSTALLATION 1989–91 Vehicles
  1. Disconnect the negative battery cable.
  2. On 1990–91 vehicles, remove the speaker grille.
  3. Remove the retaining screws from the door inside handle cup.
  4. If equipped with armrest courtesy lamps, remove the lens, detach the bulb and wiring assembly from the pull cup and remove the pull cup.
  5. Working through the pull cup opening, disconnect the remote lock rod from the lock knob.
  6. Remove the retaining screw and the remote mirror bezel nut from the power window regulator housing switch plate, if equipped.
  7. Raise the plate to expose the window switch and power door lock switch and disconnect the switches.
  8. Remove the retaining screws from the armrest finish panel.
  9. Remove the retaining screws from the armrest and remove the armrest.
  10. Using a suitable trim pad removal tool, carefully pry the trim panel plastic push pin retainers from the door inner panel. NOTE: Do not use the trim panel to pry the clips from the door inner panel. Replace any bent, damaged or missing push pins.
  11. Disconnect the radio speaker wiring, if equipped.
  12. Remove the trim panel and watershield. To install:
  13. If the door panel is to be replaced, transfer the plastic push pins to the new panel. Make sure that the watershield is positioned correctly to the door sheet metal. Remove the door pull handle from the old panel and transfer to the new one.
  14. Position the door panel loosely to the door belt opening and route the wiring harness through the appropriate access holes in the panel.
  15. Connect the radio speaker, if equipped.
  16. Align the plastic push pins on the door panel to the holes in the door sheet metal and press the pins into place.
  17. Install the armrest and route the window regulator, remote mirror cable and power lock harness through the access hole.
  18. Install the armrest finish panel.
  19. Install the power window regulator switch plate housing to the armrest connecting the power window switch, power door lock switch and remote mirror bezel nut, if equipped, prior to securing the retainer screw.
  20. Connect the lock remote rod to the lock knob retainer boss. NOTE: Make sure that the remote rod is fully seated into the retainer boss, then function manually or with the power switch to ensure smooth operation of the lock knob.
  21. Install the bulb and wiring assembly.
  22. Install the lamp lens, if equipped, and the pull cup.
  23. On 1990–91 vehicles, install the speaker grille.
  24. Connect the negative battery cable. Fig. 1: Front door panel — 1990–91 vehicles 84170064.gif
    Fig. 2: Rear door panel — 1989–91 vehicles 84170065.gif
1992–98 Vehicles
  1. Disconnect the negative battery cable.
  2. If removing the driver's door panel, remove the nut from the outside rearview mirror control switch.
  3. Remove the window regulator switch housing by gently prying up, starting at the front. Fig. 3: Front door panel — 1992–98 vehicles 84170066.gif
    Fig. 4: Rear door panel — 1992–98 vehicles 84170067.gif
    Fig. 5: Remove the window regulator switch housing by gently prying up, starting at the front 89600p08.jpg

  4. Detach all connectors from the switch housing.
  5. Remove the door inside handle cup.
  6. Remove the push pin from the door trim panel upper front extension and remove the screw.
  7. Remove the lower self-tapping screw retaining the door trim panel to the door inner panel. Fig. 6: Detach the switch housing electrical connector and remove the housing 89600p09.jpg
    Fig. 7: Remove the door inside handle cup 89600p01.jpg
    Fig. 8: Remove the screws from the door panel in the front and on the upper extension 89600p02.jpg

  8. On Grand Marquis, pry up the screw covers from the door pull handle and remove the screws and handle.
  9. Lift the door panel upward and snap out the panel. Fig. 9: There are also retaining screws located in the map pocket as well as . . . 89600p03.jpg
    Fig. 10: . . . along the bottom edge of the door panel 89600p04.jpg

  10. Disconnect the necessary wire harnesses and remove the panel. To install:
  11. Connect the wire harnesses to the door panel, as necessary.
  12. Install the door panel by pushing in and down until it snaps into place.
  13. Install all self-tapping screws retaining the door trim panel to the door inner panel.
  14. On Grand Marquis, install the door pull handle, tighten the screws and install the screw covers.
  15. Install the push pin covering screw on the panel upper front extension.
  16. Install the inside door handle cup.
  17. Install the window regulator switch housing and install the nut on the outside rearview mirror control switch, if removed.
  18. Connect the negative battery cable. Fig. 11: Lift the door panel upward and snap out the panel to remove it from the door 89600p05.jpg
    Fig. 12: Rotate the door marker lamp bulb and remove it from the door panel 89600p06.jpg
    Fig. 13: Detach the connectors for the trunklid and fuel door release switches 89600p11.jpg
    Fig. 14: Slide the relay connector off of the door panel and remove the door panel from the vehicle 89600p17.jpg
prev.gif next.gif

Aug 26, 2010 | Mercury Grand Marquis Cars & Trucks

1 Answer

How do i remove door panel to get window runner


The panel is usually a pop button type retainers holding the panel on, Obviously all screws will have to be removed ie; grab handle, internal door opening lever, and the window winder,
TIP remove window winder handle with a shoe lace or a lenght of thin material , it's a horseshoe shaped spring clip holding the winder handle on and pulling the shoe lace or material in the opposite direction of clip will easily remove clip (don't loose ) Good luck

Apr 10, 2010 | 2003 Nissan Se R

2 Answers

MY ACCENT REAR NEARSIDE DOOR WILL NOT UNLOCK, HOW DO i REMOVE THE INNER PANEL WITH THE DOOR LOCKED . OR GET THE DOOR OPEN


It wont be pretty but examine other rear door and be familiar with retaining fixings,ie door grab handle , window winder , and any screw fixings .
Remove what you can and maybe the rear seat also (sorry) The window winder removal is easier than you think ! It's held on by a horse shoe shaped spring clip, remove with a simple shoe lace or narrow piece of cloth pulled in the opposite direction of the horse shoe clip.(don't loose) This is about as much as I can help you , after this it's a tug and pull (against snap fixxings) upward lifting motion of the panel. Good Luck

Apr 05, 2010 | 2000 Hyundai Accent

1 Answer

What are the steps to replace the passenger side, sideview mirror.


if not electric, remove the screw in the end of the adjustment lever inside the car, remove the cover, undo the three bolts & it should pretty much fall off. If its electric you may have to remove the door panel 1st to access the plug. To remove the door panel carefully remove the inner door opener surround (it will either have a screw in the middle or be clipped on) if its clipped on be very carefull, they break. remove the bungs & screws holding the inner door handle on & possibly the elec window switch or winder if its not electric (small circlip behind base of winder, use hook or small screwdriver) remove any other screws you can see. CAREFULLY pull on the door panel popping the clips behind bit by bit.

Apr 05, 2009 | 1989 Toyota Corolla 2 Door

1 Answer

I need to remove the drivers internal door panel


Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Feb 04, 2009 | 2001 Suzuki Swift

1 Answer

Spring lock thingy *chuckle*


the inner door lock assembly.unscrew door handle window winder handle and unscrew lock knob.door panel should be held on by plastic push on plugs,pull off from the bottom up ,remove screws, if any. When plugs have been seperated lift panel upwards to clear top of inner door panel.Undo inner door handle and release from lock joiner rod.close to the inner door handle is a plastic rod link should be white rotate outer part until its released.the door lock<key>has a plate holding it to the door remove it and remove the lock from the rod.Remove outr door handle and remove from the rod At the bottom of the door is a bolt holding the window channel,remove the channel by unbolting,pull back window rubber and wiggle steel channel down until it slides out so the inner lock can be accessed.Remove the three large screws holding the outer door lock.it should be able to be removed. place the locks next to each other so you dont mix up the rods when you swap them over.assembly is the reverse order wind the window all the way up before you start.

Jun 13, 2008 | 1981 Ford F 100

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...