Question about Buick Roadmaster

1 Answer

Hello there are try the option you said turn on key crank then swicth only wait for 10 min.then off 3x times we make but the "PASS KEY" remain on flashing turn on ignition no crank at all.the antitefth system were i found in the buick stalled location,when i turn on swicth key no crank the ignition key holder have problem or no,when i put live posotive power to wire from ignition wire going to stater solinoid no power i puuled the sokect going to starter and i test for power in the output sockect why like this,from the key wire to output starter no power,is there any module or relay between the wire.when i jumper to solinoid to battery start but only few second engine die,or maybe the ignition coil problem in V8 engine how many ignition coil they have on buick engine pls solve my problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 6,826 Answers

What year and model is the Buick? And, are you checking for fuel and spark to start? I can look up how many ignition coil packs the Buick has, or you can count them if you see them. Is this a V8, V6, or 4 cyl. engine?

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programing passkey lll is not working security light just stays on....


Do you have a master key ?
With a master passkey III key (Black), turn ON the ignition, with the engine OFF.
Observe the Security telltale, after approximately 10 minutes the telltale will turn off.
Turn OFF the ignition, and wait 5 seconds.
Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes

Important: The vehicle learns the key transponder information and/or passwords on the ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
With a master passkey III key, start the vehicle. The vehicle has now learned the key transponder information and the PCM has now learned the fuel continue password.
With a scan tool, clear any DTCs.

May 26, 2017 | Cars & Trucks

1 Answer

1998 s-10 security light


If the security light is hot or flashing when the key is in the on position, most likely the ignition key tumbler housing has failed.

You can try resetting the pass code by turning the ignition switch to the on position (do not crank or start the engine). Leave the key in the on position for 10 minutes. Turn the key to the off position, wait 5 seconds and turn the key to the on position again and leave it on for 10 more minutes. Cycle the key to the off position again for 5 seconds the back on for a final 10 minutes. Once the final 10 minutes is complete, turn to the off position again, wait 5 seconds and now turn the ignition on and to the start position. The pass code has now been reset and it should start. If the reset does not work you will have to change the ignition key tumbler housing that contains the key code resistor.
Good luck

Apr 03, 2014 | Chevrolet S 10 Cars & Trucks

1 Answer

I have a 2001 saturn sw and replace the ign and the secuirty light flashs and eng will not crank.i dissconnected the battery over night and still the same. thanks steve


Hello: Try this procedure, Turn key on attempt to start engine leave key on, the security light should be blinking, wait 10 minutes. The security light should be off. Turn key off for 10 seconds, turn key back on (DO NOT ATTEMPT TO START) wait another 10 minutes. Turn key off for 10 seconds. Do the procedure again as in step 2. At the end of the third time turn key off then ten seconds later attempt to start the car. It should start.

Nov 25, 2010 | 2001 Saturn SL

1 Answer

The theft system wont let me turn on my car it only cranks but wont stay on


You could try resetting the computer. The car maybe in lockout mode. Try turning your car over….leave the ignition on. Wait exactly 10 min. Then try turning over again….again leave the key on. Wait exactly 10 min and do it a third time….this time the car should start…maybe run a lil rough while it relearns the processes of your vehicle again. It is important to wait the exact 10 min each time. You will probably need a battery charger or a set of jumper cables because if your car goes low during this process it will not work. Good luck and I hope this works.

Apr 06, 2010 | 2002 Pontiac Sunfire

1 Answer

2004 Alero... Cranks but won't start, have to


Yes. pass-lock has roughly a 10 minute timer.

Dec 01, 2009 | 2004 Oldsmobile Alero

3 Answers

Replaced ignition switch 2003 chevy impala and car will not start


After you replace the ignition switch turn the key to start the car and release leave the key were it stops after trying to start wait 10 minutes until security light goes out turn key to full off position then repeat the above procedure two more times for a total of three on the 3rd attempt to start car wait for light to go out then turn key to full off positoion wait 10 seconds then try to start car body control module should learn new pass code and the car should start.
Big john, J@J Automotive

Sep 15, 2009 | 1999 Chevrolet Lumina

1 Answer

When starting car, takes 8-10 sec to turn over.


Do you mean 8 to 10 seconds to START? Turn over means the engine is turning or cranking BUT starting is when the engine is actually running. I think you might have a fuel problem like your loosing your prime. Turn the key off wait 15 sec. then turn the key ON not cranking it repeat this (3x) if the car starts immediatedly your fuel pump is loosing its prime or the fuel pressure regulator is leaking.

Jul 13, 2009 | 2001 Isuzu Rodeo

1 Answer

Saturn LS1 2000 wants to start but won't


The fab key activates the security system in the car, the ignition pass lock may need to be reset to your ignition key's. It Takes about 30 min to do. Try resetting the pass lock to read your ignition keys. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK. Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps. The ignition keys has a resistor value for the ignition to read and after a few years the resistance may change and the Pass Lock has a had time reading it's value so you have to reset the pass lock to read the keys again.

Jun 12, 2009 | 2001 Saturn SL

2 Answers

98 ford mustang stuck in security mode


sounds like ecm lost signal from key

Sep 27, 2017 | 1998 Ford Mustang

1 Answer

My 1995 nissan altima will nopt crank when i turn the key everrything shuts off and the only thing that stays lite on the dash is the word security


HELLO I HAD THIS SAME PROBLEM ON A 01 OLDS AERO I KNOW YOUR CAR IS A NISSAN BUT TRY THIS IT MIGHT WORK FOR YOU
TRY STARTING CAR IF NOTHING LEAVE KEY ON FOR 10 MIN AND THEN TRY TO START CAR AGIAN DO THIS 3 TIMES AND LEAVE KEY ON FOR 10 MINTUES AND DO NOT TRY TO START CAR JUST WAIT AND FOURTH TIME TRY TO START IF NOTHING TURN KEY OFF AND WAIT 10 MIN AND THEN TRY TO START YOUR CAR WHAT THIS DOES IS RESET YOUR SECURITY SYSTEM IN YOUR CAR

Jan 09, 2009 | 1995 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...