Question about Toyota Corolla

Open Question

I changed the head gasket on TOYOTA COROLLA MODEL-AE 92 MAKE-1990 4AFC ENGINE. FORGOT TO MARK TIMING ON THE both cams can u tell me to Align those again. Try to align but still not starting up.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Fixe_You
  • 1800 Answers

SOURCE: Looking for owners manual

here is is

give me fix ya rate


http://www.eserviceinfo.com/downloadsm/29134/TOYOTA_COROLLA%201997.html

Posted on Aug 18, 2008

freetek
  • 5568 Answers

SOURCE: bolt torque specs

I have used Haynes service manuals for (hate to admit it) many decades and I recommend you check to see if this one:

http://www.amazon.com/Haynes-Toyota-Automotive-Repair-Manual/dp/1563923513

doesn't cover your engine.

I have found darned few 'holes' in their coverage.

Auto parts stores carry these and I suspect that even though sealed, the sales people will not give you too hard of a time if you explain you want to insure you are getting what you need.

Haynes is not the same as it was 20 years ago before they were acquired by Chilton but the price/utility ratio is still pretty good.
Mostly I'm annoyed by the move to cheaper paper (newsprint)that is fussier, picks up dirt, tears more easily than the better paper of yore.

Posted on Aug 20, 2008

  • 73 Answers

SOURCE: 1990 toyota camry

Well if it is a 4 cylinder the timing marks would be small hole in camshaft lined up with little dot on head at 12 o'clock position and the crank with the pulley on should line up with 0 on the timing indicator. If it is a 6 cyl then the marks would be- camshafts both with dots up and lined up with indicaters on heads and crank timing mark on 0 with the harmonic balancer installed. Hope this helps.

Posted on Sep 12, 2008

freetek
  • 5568 Answers

SOURCE: 1994 Toyota Corolla - Valve COver Gasket Replacement

You need an aftermarket serviice manual from Haynes or Chilton. They will have that kind of info.
I know of no car (I don't know them all) where that is needed and depending on the cover material (sheet steel or cast), could lead to warping and new leaks. I always use a thin film of silicone whether it is specified or not and there are torque specs for ALL valve covers I have ever seen.  

Posted on Sep 13, 2008

  • 231 Answers

SOURCE: head gasket on my 1990 toyota V6 3.0

I would highly recommend that you go to the local parts store and purchase a Haynes Manual for your vehicle, they are around $ 25.00 Canadian. As when you do your head gasket you wil need to remove your timing belt and this is a procedure in it's self. then you will neen certain torque settings. This manual will provide you with all of this information step by step. they are designed for the do it yourselfer. They also cover many other issues that you may come across through out the ownership of your vehicle. I know that the last ting you need is an added exspence but these manuals are well worth the small investment. There is a site that you can find hrough google search that you can find factory service repair manuals for your vehicle, however they only have a layout for a 4 cylinder engine in there drawings and this is alot different then the 6 cylinder. As the procedure for repairs is totally different. I hope that this helps and that you take the time to rate any solutions you receive. Good Luck.

Posted on Oct 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the timing marks of toyota 2.7 vvti engine


Timing marks are always in the same place regardless or make. Engine timing marks are a notch on the crankshaft pulley with marks on a casting or metal plate next to the crankshaft pulley.

Camshaft marks are on one (single cam) or both (twin cam) cylinder head pulleys with a fixed mark on top of or central to the pulleys.

These videos may help you.

How to assemble engine VVT-i Toyota Part 30: Timing chain ...

? 36:20
https://www.youtube.com/watch?v=UJA1yKZAXuU
Apr 26, 2014 - Uploaded by Peter Finn
How to assemble engine VVT-i Toyota Part 30: Timing chain setup ..... Would the 2.7 VVT-i Toyota engine ...

How to check timing chain status VVT-i engine Toyota ...

? 1:03:59
https://www.youtube.com/watch?v=2d6cwjiuPeA
Oct 12, 2013 - Uploaded by Peter Finn
How to check timing chain status VVT-i engine Toyota Corolla. Gasoline engine. Years 2000 to 2008. Also ...

Feb 14, 2016 | Toyota Cars & Trucks

3 Answers

Setting timing marks to get vehicle to start after engine overhaul


Timing marks setting Corolla 4A-FE.
Align the notch on the crankshaft pulley with the "0" mark on the timing belt lower cover.
25679262-y0srr1ownybx5goll4rgvnpm-5-0.jpg

With the crankshaft pulley being aligned with the 0 mark on the timing belt cover, the hole on the camshaft sprocket should exactly be in front of the notch of camshaft bracket.


25679262-y0srr1ownybx5goll4rgvnpm-5-2.jpg
Hope that works.

May 04, 2015 | 1998 Toyota Corolla

1 Answer

How do I replace camshafts on Toyota Hilux 3.0 d4d?


The Toyota Hilux D4D 3.0 1KDFTV is an interference engine, so if the timing is wrong then the pistons will critically damage the valves. Removing the camshafts is easy, you just need to remove the set of bearing cap bolts that fasten them, in a predetermined order. When reinstalling the camshafts you just need to ensure the peripheral stamp marks on each of the camshaft sprockets align with each other. ie Align the indented dot with its adjacent indented dot or align the highlighted indented dot with its adjacent highlighted indented dot. The bearing cap bolts will need to be fastened with a torque wrench. Then connect the timing gear pulley onto the right camshaft using a key woodruff slotted into the right camshaft groove. Always double check the timing - that the peripheral stamp marks align. Don't under tension bolts, don't over tighten bolts either.

Sep 12, 2014 | Toyota Hilux Cars & Trucks

1 Answer

How to set timing on toyota 2E


Crankshaft on TDC Cam wheel cover off Cam wheel mark up the top aligned to head mark Distributor set to no 1

Aug 13, 2011 | 1986 Toyota Corolla 2 Door

1 Answer

I have a 2004 corolla and has a timing chain making noise , now i pull the timing cover out but forgot to align the marks, and i think i move my camshaft now i need to set the marks again , what u think


me think you um not give enough information.
You changed the belt?
Just reset it to tdc and align the marks like you were doing it for the first time.
If it is off a degree it will run. It will not run good.
Replace the tensioners when this done yes.
Align marks and reinstall.

Jan 04, 2011 | 2004 Toyota Corolla

1 Answer

You are changing the timing belt and you need o know where the timing marks are for the cam shaft and the crankshaft on a 1994 corolla Also how do you align the marks to put engine in time?


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1994 Toyota Corolla. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1994/make/toyota/model/corolla/1994_toyota_corolla_timing_belt_diagram_marks.htm

Sep 04, 2009 | 1994 Toyota Corolla

1 Answer

How do i set the timing after replacing the cambelt.


Put the engine at TDC compression stroke , Thats when the valves are both closed on No 1 cyl and the piston is on its compression stroke .then align all cam and crank marks. set dizzy on No 1 cylinder (rotor pointing at #1 plug wire) . rotate engine 2 revolutions and recheck all marks. Fire away

Aug 24, 2009 | 1989 Toyota Camry

1 Answer

Where are the timing marks on a 4ZZ-FE engine?


Please buy a cheap shop manual. Get this wrong and you will be very sorry.

May 05, 2009 | 2001 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...