Question about 2002 Nissan Altima

2 Answers

02' Nissan Altima, car jerking, turns off at light, but turns right back on. Engine light on, code from autozone P0335 crankshaft position sensor. P0725 Engine speed signal circuit. The start up, days it just starts right up, other days, it stalls. Could it be fuel pump?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 678 Answers

If it has a code for loosing the crankshaft position sensor signal, I would certainly start looking at that before venturing into the fuel system. Cam and Crank sensors are a common failure item for Nissans of that era. Nissan actually redesigned the sensor and i think they performed a recall on some vehicles. They are fairly inexpensive and easy to replace. I believe they run about $40 each. Because most people don't have access to a powerful scanner or a digital storage oscilloscope to verify the failure I recommend replacing the cam and crank sensors at the same time.

Posted on Sep 02, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a problem 2 spark plug working 2 not working i chick come d t c p0335

Posted on Dec 26, 2011

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 45 Answers

SOURCE: engine speed signal circuit

there is currently a recall being performed on altimas and there is also a updated crank position sensor check with your dealer for open recalls on your vehicle (its just a phone call away have your vin # ready (located on left bottom of windshield if your facing it from in front of vehicle it is on lower right side of windshield - also look on driver door jamb.

Posted on Aug 28, 2008

NismoMaster
  • 146 Answers

SOURCE: Crankshaft Position Sensor Error P0335 recurred after r&r

In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Po335, engine ligt on, slip and vdc brake light on 2005 armada


Error Code: P0335
Description:
Crankshaft Position (CKP) Sensor - Circuit Malfunction
Possible Cause:
Wiring.
Crankshaft position (CKP) sensor.
Engine control module (ECM).

Mar 25, 2014 | 2005 Nissan Armada

1 Answer

Replaced camshaft and crankshaft position sensors in my 2005 altima also the o2 seneor car still will not run. error code 335 What else could be the problem?


DTC P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

If you need additional details about test and solutions, just contact us in the Code Link.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using Fixya, and have a nice day.

Jose.

Oct 21, 2011 | 2005 Nissan Altima

2 Answers

I have nissam altima 2005 and it turned off in middle of the road today and then it showed battery sign but it was showing service engine sign from two days. when i went to autozone today then check...


Stay away from autozone. Go to a reputable garage, and tell them if you intend to fix it yourself.For a fdew bucks you can have a real mechanic diagnose it, and be sure you are fixing the correct thing, not just tossing parts at it, as they love you to do at the zone. If the engine was still running when the battery light came on , this sounds like an intermittant charging problem Have your battery and charging system professionally checked. It could also be caused bt the belt slipping, for instance if it was wet, or the steering was held on one of the stops, in a sharp turn. P0335 is indeed a crankshaft sensor code and should be checked and replaced if neccessary.Appears that there is an updated sensor, and it's very hard to plug in. Let me know if I can help furthur.

May 13, 2011 | Nissan Altima Cars & Trucks

1 Answer

Service Engine Light On


It has to do with the cps, crankshaft position sensor. Take it to Autozone and ask them to pull the codes to verify them. They will then sell you, if you want it, the correct part - this service is free at autozone!!

Apr 19, 2010 | 2002 Nissan Altima

1 Answer

2005 Nissan Altima, Car keeps stalling and is jerking while driving. Check engine light says crankshaft position sensor, but I changed it and it's still doing it.


2005??? dealer only encrypted software so a plug in scanner will read the wrong code .From description try changing the coil pack

Nov 30, 2009 | 2005 Nissan Altima

1 Answer

Nissan Altima 2004 SES light and some times engine donot start


its going to be between the motor and tran on the back lower part it is going to be in between a small gap i chande it on my friends car and it work

Aug 24, 2009 | 2005 Nissan Altima

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

1 Answer

Crankshaft sensor


Replace the air flow meter.

Jul 19, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
2002 Nissan Altima Logo

1,133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...