Question about 1998 Chevrolet K1500

1 Answer

Show all bolts necessary to remove oil pan it won't come down. how do I remove it?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 31 Answers

If all the bolts have been removed the it may just need a little tap to come loose

Posted on Sep 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the oil pump on a 2000 lexus es300


Drain oil from the oil pan and recycle. Remove bolts holding oil pan up and remove oil pan. Remove bolt holding oil pump in. Install new pump. Replace oil pan gasket if necessary. Reinstall oil pan. Reinstall drain plug and refill with oil. Start engine and watch oil pressure gauge or light. Oil pressure should be normal almost instantly. Check for oil leaks.

Jul 31, 2016 | 2000 Lexus ES 300

1 Answer

Change oil pan on a 2001 sonoma


the 2.2 engine and the 4.3 engine with 2WD MODEL you have to remove engine.the 4WD MODELS, you have to remove all these parts first remove dip stick, drive belt, splash shield, remove front axle shield and the transfer case shield, front skid plate and the flywheel cover,remove left and right engine mount through bolts.then raise the engine using a lifting device, and block in position,using large wooden blocks between the motor mounts and brackets.you will also need to remove these parts,remove disconnect oil cooler line, remove pitman aem bolt and pitman arm, remove idler arm bolts and idler arm, remove front differential through bolts,remove front driveshaft if necessary,remove differential assembly by rolling it forward for clearance, remove starter motor, then remove oil pan bolts then remove oil pan, your oil pan need to be flushed slightly forward of rear of the block to allow proper alignment with the transmission housing.using feeler gauge measure the 3 oil pan to transmission contact points.clearance should not exceed 0.011 in. 0.3mm if so realign the oil pan.oil pan bolts torque is 18 ft lbs tighten oil pan bolts in sequence.

Aug 25, 2012 | Cars & Trucks

1 Answer

How do you remove the oil pan on a 1991 cadillac DeVille?


You may have to drop one end of the oil pan down enough for you to put your arm in and unbolt the oil pump. The oil pump hanging down in the pan won't allow you to pull the pan out until the pump is unbolted.

Jul 20, 2012 | 1991 Cadillac DeVille

1 Answer

Haw to install oil pan gasket on1991 BMW 850i


drain the oil first as if your doing an oil change. undo all the bolts around the entire perimeter of the oil pan. drop it down.scrape the old gasket off of both the pan and the engine where it was mounted. Clean both surfaces well. put the new gasket on the pan and reverse the instructions for removal. jump from bolt to bolt in an crisscross pattern or else it won't seal right replace the drain plug may as well replace the oil filter and add new oil.

Jul 15, 2012 | BMW 750 Cars & Trucks

2 Answers

When changing the oil pan on a 2006 town & country do you have tighten the bolts in a sequence?



Removal & Installation

2.4L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.

To install:
  1. Install or connect the following:

    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.

To install:
  1. Install or connect the following:

    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    0996b43f8020961b.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Oil pan mounting bolt tightening sequence-3.0L engine


To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:

    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:

    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

May 05, 2012 | 2006 Chrysler Town & Country

1 Answer

How to do an oilpan on a 88 chevy montecarlo


  1. Disconnect battery negative cable.
  2. Remove air cleaner.
  3. Remove upper fail shroud (V8)
  4. Raise vehicle and drain oil pan.
  5. Disconnect A.I.R. hose at converter pipe (V8)
  6. Disconnect A.I.R. pipe at exhaust manifold (V8)
  7. Remove exhaust crossover pipe at manifold and converter.
  8. Remove starter.
  9. Remove flywheel cover.
  10. Disconnect transmission oil cooler lines at oil pan.
  11. Remove engine mount 'through' bolts on V8. Loosen right bolt and remove left on V6.
  12. Remove oil pan bolts and lower oil pan. Check that forward crankshaft throw and/or counter balance weight are not extending downward so to block oil pan removal. Turn crankshaft, necessary, to put throw on horizontal plane.
  13. Raise engine.
  14. Remove oil pan.
Installation


  1. Clean sealing surfaces on cylinder case and pan.
  2. Check oil pan gasket for damage; replace if necessary.
  3. Apply a small amount of 1052751 or equivalent to front and rear corners of oil pan.
NOTICE: Only a small amount of sealant is required. Excessive amounts of sealant may cause a problem with proper sealing of oil pan.


  1. Install retaining bolts and torque to 9 N.m (80 lb. in.).
  2. Raise engine, if necessary.
  3. Lower engine, install mount 'through' bolts and torque to 50 lb. ft. (65 N.m).
  4. Install torque converter cover.
  5. Install starter.
  6. Install exhaust crossover pipe at manifold and converter.
  7. Lower vehicle.
  8. Install fan shroud.
  9. Install air cleaner.
  10. Fill crankcase with oil.
  11. Connect battery negative cable, start engine and check for leaks.

Nov 30, 2010 | 1987 Chevrolet Monte Carlo

2 Answers

When changing the trans fluid on my 2004 Avalanche, I understand that you have to disconnect the trans lines from the radiator and run the engine until the fluid stops flowing. Is this correct? If so, do...


I didn't read about running the engine at all during the transmission fluid change. --- Removal & Installation 4L60E/4L65E To Remove:
  1. Raise and safely support the vehicle.
  2. Place a drain pan under the transmission.
  3. If equipped with a drain plug, drain the transmission fluid.
  4. If necessary, remove the bolts and position aside the range selector cable bracket for clearance while lowering the pan. It is not necessary to remove the cable from the lever or bracket.
  5. Remove the catalytic converter.
  6. Remove the oil pan bolts from the front and sides of the pan only.
  7. Loosen the rear oil pan mounting bolts about 4 turns.
  8. Lightly tap the oil pan with a rubber mallet in order to loosen the pan and allow the fluid to drain.
  9. Remove the remaining oil pan bolts.
  10. Remove the oil pan and the gasket.
  11. Remove the filter by twisting and pulling on it.
  12. Remove and discard the filter seal. The filter seal may be stuck in the pump; if necessary, carefully use pliers or another suitable tool to remove the seal.
  13. Clean the transmission and the oil pan sealing surfaces with solvent, and air dry. You must remove all traces of the old gasket material.
To Install:
  1. Coat the new filter seal with transmission fluid.
  2. Install the new filter seal into the transmission case. Tap the seal into place using a suitable size socket.
  3. Install the new filter.
  4. Install the oil pan and new gasket. Tighten the bolts alternately and evenly to 97 lb in (11 Nm).
  5. Install the catalytic converter.
  6. If previously removed, install the range selector cable bracket and bolts. Tighten the bolts to 18 lb ft (25 Nm).
  7. Apply a small amount of sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the oil pan drain plug, if equipped.
  8. Install the oil pan drain plug, if equipped. Tighten the plug to 13 lb ft (18 Nm).
  9. Lower the vehicle.
  10. Fill the transmission to the proper level with DEXRON® III transmission fluid.
  11. Check the COLD fluid level reading for initial fill only.
  12. Inspect the oil pan gasket for leaks.
4L80E/4L85E To Remove:
  1. Raise and suitably support the vehicle.
  2. Place a drain pan under the transmission oil pan. Drain the transmission fluid and install the plug. Tighten the drain plug to 13 lb ft (18 Nm).
  3. Support the transmission with a transmission jack.
  4. Remove the transmission crossmember.
  5. Disconnect the range selector cable end from the transmission range selector lever ball stud. NOTE: It is not necessary to remove the selector cable from the bracket.
  6. Remove the transmission range selector cable bracket. Reposition the bracket and cable.
  7. Remove the oil pan bolts. NOTE: The transmission oil pan gasket is reusable. Replace as needed.
  8. Remove the oil pan and gasket.
  9. Remove the magnet from the bottom of the pan, if necessary.
  10. Remove the oil filter and neck seal.
To Install:
  1. Clean the transmission and the oil pan sealing surfaces with solvent.
  2. Install the filter neck seal and filter.
  3. Install the oil pan gasket to the pan.
  4. Install the magnet into the bottom of the pan, if necessary.
  5. Install the oil pan and bolts. Tighten the oil pan bolts to 18 lb ft (24 Nm).
  6. Install the transmission range selector cable bracket. Tighten the bolts to 18 lb ft (25 Nm).
  7. Connect the range selector cable end to the transmission range selector lever ball stud.
  8. Install the transmission crossmember. Tighten the fasteners to 70 lb ft (95 Nm).
  9. Install the transmission mount nuts. Tighten the nuts to 30 lb ft (40 Nm).
  10. Remove the transmission jack.
  11. Lower the vehicle.
  12. Fill the transmission to the proper level with DEXRON® III transmission fluid.
prev.gif next.gif

Aug 26, 2010 | 2004 Chevrolet Avalanche

1 Answer

How to change oil pan gasket for 2005 dodge caravan


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004

Oil Pan - Removal & Installation

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.
To install:
  1. Install or connect the following:
    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    e6c7cfd.jpg
    Fig. Oil pan mounting bolt tightening sequence-3.0L engine

To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:
    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:
    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

Hope helps (remember rated this).

Jun 24, 2010 | 2005 Dodge Caravan

2 Answers

How do i change oil pan gasket on 1988 e-350


You should be able to drop the pan by removing the bolts. On some vehicles it is necessary to jack the engine up after removing the bolts from the engine mounts. If this is necessary then once you have your engine up high enough (usually 3 to 4 inches) put small blocks of wood where the mount would go to support the engine while you remove the oil pan. Also you can work the oil pan gasket around the oil pickup tube with the pan down with out having to totally remove the pan from underneathe the truck. If you do this just make sure the gasket is not twisted before reinstalling the pan onto the engine.

Nov 03, 2009 | 2002 Ford E350

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...