Question about 1998 Ford Explorer

1 Answer

REPLACEING FUEL FILTER - 1998 Ford Explorer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Expert
  • 260 Answers

Pressure Relief
Special Tool(s) EFI/CFI Fuel Pressure Gauge
310-012 (T80L-9974-B) REPLACEING FUEL FILTER - swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related component. Highly flammable mixtures are always present and may be ignited, resulting in possible personal injury.
WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before servicing or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved to prevent accidental spraying of fuel, causing personal injury or a fire hazard.

  1. Remove the schrader valve cap and attach the EFI/CFI Fuel Pressure Gauge.
  2. e5e3ebf.gif
    NOTE: Open the manual valve slowly to relieve the system pressure. This may drain fuel from the system. Place fuel in a suitable container.
    Open the manual valve on the EFI/CFI Fuel Pressure Gauge slowly and relieve the fuREPLACEING FUEL FILTER - 9deacdd.gif. 9deacdd.gif
    Filter Removal
    1. Relieve the fuel pressure; refer to Above.
    1. Remove the fuel filter (9155).
      1. Disconnect the fuel lines
      1. Remove the fuel filtREPLACEING FUEL FILTER - b717c63.gif fuel filter support.
      2. b717c63.gif
      1. Push Connect Fittings
        Special Tool(s) REPLACEING FUEL FILTER - 4bbcf9e.gifl Line Disconnect Tool
        310-S039 (T90T-9550-S) 4bbcf9e.gif
        1. Relieve the fuel pressure; refer to Pressure Relief in this section.
        1. Disconnect the safety clip frREPLACEING FUEL FILTER - f0af03c.gif hose.
        2. Install the fuel line disconnect tool and push into the fitting.
          Install the fuel line disconnect tool and push into the fitting. 367328f.gifSeparate the fitREPLACEING FUEL FILTER - 3beef33.gifl class="h_mi">
        1. Inspect for damage.
          • Clean the fittings.
          • 3beef33.gif

Posted on Sep 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lack of fuel pressure on 4.8 liter gmc


fuel supple issue-as shown be replacing fuel filter and seeing an improvement-next thing to try- put a new fuel pump in- Denny

Nov 27, 2013 | 2001 GMC Yukon

2 Answers

MY CAR TAKES FOREVER TO START


its probally the starter motor will need replaceing otherwise try replaceing the fuel filter.
martyn

Apr 08, 2013 | Cadillac Cars & Trucks

1 Answer

2010 ford expedition stalls after refuel


Sounds like a dirty fuel filter but if you have the problem after replaceing filter Check fuel pressure it may be low after testing If it is I would replace fuel pump . I hope the fuel filter solves the problem its a lot less expensive if this was helpful please leave me good feedback

Feb 20, 2013 | 2001 Ford Expedition

1 Answer

1979 el camino fuel filter


if you have a quadrajet carb it will be right at the fuel inlet, front of the carb. you may have an inline filter instead or also, this would be in the line between the fuel pump (front left side of engine block as you look at the engine) and the carb

i usually remove the one that is in the carb and put in an inline filter myself, it makes replacement so much easier.. the carb housings like to strip out

Feb 05, 2013 | Chevrolet El Camino Cars & Trucks

1 Answer

No fuel to carb after replaceing pump


Check filter. If there is fuel at the filter then it sounds like you have got a bad pump. I have had this happen more than once.

Aug 08, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

It will start then quit running as soon as it gets gas


Try replaceing your fuel filter . Its a pressureized system if the filter is cloged say 80 % the pressure would still push enough fuel to start the vehicle but when it has to run the engine would starve for fuel and stall and this will also damage your fuel pump if not corrected so check the filter its in the fuel line under the vehicle follow it from the tank its a metal line and will be under the drivers door area and be mounted to the frame rail in the gas line

Apr 15, 2011 | 1998 Chevrolet Cavalier

2 Answers

No fuel into carborator


  1. Check if there's fuel in tank. :)
  2. Check the vacum
  3. Check the fuel pump

Aug 08, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1998 Ford Explorer Logo

1,013 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...