Question about 2006 Hyundai Sonata
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
inside the sun visor there is a spring which is moving to side when you push down the spring pushes side so it will keep down when you want to push to the normal possition spring releces and keep to that possition any way i would like to advice you to replace sun visor.
Posted on Nov 28, 2008
I resolved this same problem on my 2004 Murano after also being told that it ($350 Visor) was not covered under my extended warranty. This problem is primarily caused by the heavier than normal visor. It cost me a total of $2.69 and about 30 minutes to fix.
To resolve this problem follow the following steps:
1) Go to the hardware store and purchase the Velcro package that contains (2) 18”, 1/2 inch strips (I chose the beige color since I have a tan interior) 2) Using a small screw driver, carefully pry off and remove the small cover that hides the mounting screws for the Driver’s visor. 3) Remove the 2 Phillips screws and drop the visor down slightly so that you can unplug the wires that go to the visor light and now remove the visor 4) Using the plastic velcro strip ONLY , (NOT the fuzzy strip), trim the end of the strip so that it will fit under the visor mount and also punch a small hole in that end of the strip so that one of the screws will go through it. (There is NO NEED to remove the adhesive backing from the Velcro strip)
5) Carefully mount the visor so that one of the mounting screws also goes through the Velcro strip 6) Be sure that the sticky side of the Velcro strip faces down or towards the visor
7) Once the visor is loosely mounted, pull the Velcro strip slightly and then tighten the 2 mounting screws securely. 8) Once mounted, hold the Velcro strip against the headliner and then raise the visor against the strip and the headliner and it SHOULD stick in place since it can’t drop down because one end of the Velcro strip is secured to the visor mount 9) Trim the exposed end of the velcro strip so that only 1 inch is exposed (or less) in case you need to lower the visor at a later time. (I removed a half inch of the backing and folded the exposed end on itself so that it's easy to grasp.) In this way you don’t have to glue anything to the headliner OR the visor.
(If your visor is a vinyl material, you will have to stick/glue the fuzzy velcro strip to the top side and/or edge of the visor so that there will be something for the plastic strip to stick to)
I hope this helps others…. It works for me! (and it sure beats $350!!)
Posted on Jan 30, 2009
SOURCE: driver side sun visor falls down
If you have anything on top of the visor, remove it. If there are any screws visible near the pivot rod, tighten them. You can remove the visor and slightly bend the pivot rod, inside the visor. You can just buy a new one and replace it yourself. It's only a few screws.
Posted on Sep 16, 2009
Tips for a great answer:
Feb 18, 2012 | 2007 Kia Sportage 2.7
Aug 02, 2010 | 2007 Toyota Camry
Jan 07, 2010 | 2005 Ford Explorer
Sep 16, 2009 | 2005 Nissan Murano
Aug 20, 2009 | 2000 Toyota Celica
Jul 30, 2009 | 2003 Toyota Highlander
Jun 02, 2009 | 2005 Nissan Murano
Nov 28, 2008 | 2003 Toyota Highlander
197 people viewed this question
Usually answered in minutes!