Question about Mazda 626

Open Question

Timing diagram for 1998 mazda 626 4 cylinder 2.0 L there are punched marks on the cam gears and another marks that says "I" also raised cating marks that are on the outer edge of the cam gears. very confusing as to which marks are the ones to work with, any help you can give would be appreciated. Thank you

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1757 Answers

SOURCE: what do timing marks on a mazda 626 yr 2000 4cyl

Click on the following free, direct Link. It has all the Timing Belt Diagrams you will need, complete with Instructional and Directional Diagrams to set your Timing.

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2000/make/mazda/model/626/2000_mazda_626_timing_belt_diagram_marks.htm

Posted on Apr 05, 2010

Ad
alicantecoli
  • 22219 Answers

SOURCE: what are the timing marks

on the back of the cams ,two slots that must be horizontal .

Posted on Dec 26, 2008

  • 36 Answers

SOURCE: Want to remove the ignition lock cylinder since a broken key is stuck inside.

get a phillipshead un do about 4 screws from underneath plastic cover which hides steering colume. remove cover you will see white plug on the left hand side of ignition barrel disconect.then right hand side there will be acable disconect.now get a small chissel and anti clockwise tap bolts which have no heads on them that are on top of steering colume when they are alittle bit lose use plyers its easier pull bolts out clamp will then come of and then you can pull whole ignition of. now there is 2 brass pins which hold barrel in ignition up near the key end remove and barrel will come out but it might be easier to take whole ignition to locksmith and get them to do it and get new key for around 30 bucks i did a mates about couple months ago seeya orangepeel.

Posted on May 26, 2009

  • 1757 Answers

SOURCE: isuzu trooper 2002 RLV engine. camshaft timing

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams and Photos with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams, instructions and photo's for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2002/make/isuzu/model/trooper/2002_isuzu_trooper_timing_belt_diagram_marks.htm

Posted on Mar 25, 2010

dj_relly999
  • 4070 Answers

SOURCE: I need a 2001 Mazda

Hi! There seems to be no site for a 2001 mazda 626 cylinder repair. Try haynes or chilltons manual from the bookstore or autoparts supply. Hope this helps and have a good one!

Posted on Jun 10, 2010

Testimonial: "Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset the timing?


First pull the timing belt tensioner then slip the belt off the cam gears. You then need to find TDC (Top dead center). 3 ways to find TDC 1) There are marks on the crank pulley align them for TDC. 2) Remove timing cover and use crank gear mark seen in link below 3) Put the dip stick in cylinder 1 and turn engine until dip stick stops going up. After finding TDC align cam gear marks seen in link below. Now make sure both cam and crank stay in position and slip timing belt back on (you can move the cam gear to get the belt on but make sure the marks are aligned after the belt is on). Last tighten the belt tensioner, I usually use my finger or an extension to get some more tension on the belt. You might have to remove engine mount bracket makes life much easier as the front cover section is TIGHT !!!. Turn engine a few times to make sure you have compression and engine turns without getting stuck. See link below good luck.

http://bladeagenos21.soup.io/post/374487151/timing-marks-on-mazda-626-1994-diagram

Jul 08, 2014 | 2002 Mazda 626

1 Answer

What is the torque for a 1983 mazda 626 fe sohc engine


go to autozone.com and login or set up an account if you don't already have one it's free. Then you will be able to punch in the year make and model of your car and find repair manuals for any vehicle you desire. In your case 83 mazda 626. and go to cylinder head info and there you will find what your looking for. Good luck.

Jun 06, 2014 | 1983 Mazda 626

1 Answer

What is timing belt installation sequence on a 1999 Mazda 626 6 cylinder?


set mark on crankshaft to TDC mark on timing cover. set mark on cam pulley to align with mark on head .if more than one mark on pulley rotate by hand till exhaust and inlet just rocking then align closest marks .

May 11, 2014 | Cars & Trucks

1 Answer

Timing belt installation on 1999 mazda 626 6 cylinder need timing mark alignment sequence


Why you buy a timing belt kit ,you get a
booklet of pictures & instructions

Why you buy just the belt, you should have that as well

If not-- google the question, as well as look for a
You Tube Video on the belt replacement & how to time it
& the cam gears

May 11, 2014 | Mazda 626 Cars & Trucks

2 Answers

I need the markings on a mazda xl v6 timming belt


Hi Marina,

These diagrams may be a little hard to see, but the cams have a mark that align with the raised "V" on the rear timing cover and the crankshaft pulley has a notch that aligns with the mark in the 12 O'clock position on the oil pump housing.

10_16_2011_10_28_43_pm.gif

10_16_2011_10_29_28_pm.gif

Oct 16, 2011 | 2002 Mazda 626

1 Answer

2002 mazda 626 replacing timming belt need to know where timming mark are and where to turn them ///v-6 dohc


TIMING MARKS SHOULD BE A NOTCH ON THE CAM GEAR, AND ONE ON THE CRANK GEAR! THEY SHOULD BE LINED UP FACING EACH OTHER!

Feb 22, 2011 | 1999 Mazda 626

1 Answer

What do timing marks on a mazda 626 yr 2000 4cyl cam gears look like


Click on the following free, direct Link. It has all the Timing Belt Diagrams you will need, complete with Instructional and Directional Diagrams to set your Timing.

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2000/make/mazda/model/626/2000_mazda_626_timing_belt_diagram_marks.htm

Mar 29, 2010 | 2000 Mazda 626

1 Answer

Timing Belt 2002 Mazda 626


re-install belt, lining up the timing marks, crank to TDC #1 cylinder, cma pulleys have marks on them, line them up to the index marks as well. If you have a drive wheel in the air, you can pop the car into 5th gear (make sure it's chocked!) and rotate the wheel to turn the engine for alignment, etc. You can put a wrench/socket on the cam bolt to align it as well.

Aug 04, 2008 | 1999 Mazda 626

10 Answers

Need to know how to time my car


how do i get the timing back where it belongs on my 2006 chrysler 300 i messed with it before i realized it had marks

Jul 23, 2008 | 1995 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...