Question about Chrysler Sebring

1 Answer

I tried to pull it into reverse and it just pops back into park.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

The shifting detent is not holding for the cable is bounded up someway

Posted on Sep 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to I repair my shift gears on my Chrysler 2007 Sebring? It's stuck in park.


I assume this is a floor shift,remove shifter knob, pry the trim around the shifter up to remove to get to the 2 screws there, in the storage compartment there may be 4 screws, pull Ebrake up as far as you can then rear of console upward over ebrake handle then back,remember you have to reverse what you just did to put it back together. If your after the shift cable try to pop it off the trans first to see if it can be moved out of park at the trans if so more likely is the cable if not you may have internal trans problem.

Dec 27, 2014 | 2007 Chrysler Sebring 2.7

1 Answer

700R4 Chevy trany try's to pull in park and pulls in nutural and locks up in reverse


Overdrive clutches are smoked... That will require an overhaul. That's pretty typical for 700R4 and 4L60E, as the internals are nearly identical. Usually caused by a mid adjusted TV cable.

Dec 08, 2014 | Cars & Trucks

1 Answer

1999 Chevy Tahoe will not go into park at all all other gears work but feel loose


there is adjustment down on the ******. I will send you a picture, what you will need to do it put on the e brake,and block the tires. on the drivers side of the ****** the shift cable is located, pop off the cable from the arm and pull the white clip, when push the arm foward that is park,and then easily pull the cable to the arm and put back the white clip10_30_2012_8_31_59_am.gif

Oct 30, 2012 | 2000 Chevrolet Tahoe

1 Answer

Shifter stuck in park selector light in reverse and in reverse,shifter wont move out of park


The SHiFT lock is broken or not pulling up when u disengage the reverse and PARK!
SHiFT LOCK is the one in ur SHiFTiNG KNOB, when u try to release the PAR or going to reverse u have to pull/press it!
The only way you could release and check it, is by dismantling the whole shifting console, and check where it is disconnected or go to the nearest garage to fix on that!
Hope that helps u out!

Nov 18, 2010 | 2004 Jaguar XJ-Series

1 Answer

What could my problem be if i have a 97 5 speed jetta and every time i put it in reverse it wants to pop out of gear


if you pull into a parking spot by turning into it, there may be bound up tension in tranny from the differential. mine hates to go into reverse unless i pull through or straight in to a spot.

Jun 07, 2010 | 1997 Volkswagen Jetta

1 Answer

When i take it from park into reverse it pops really loud


Do you park on a hill, and not use the parking brake?? When folks don't use the parking brake, the car rolls a bit after you put it in park, and take your foot off the brake. Therefore putting pressure on the transmission to keep the car in place. Then when you start up, and throw it in reverse, it will pop, clunk, make an awful sound.

Apr 02, 2010 | 2003 Pontiac Aztek

1 Answer

Sebring 08 stuck in park


try checking the oil level or linkages

Sep 20, 2009 | 2007 Chrysler Sebring Sedan

1 Answer

91 cavalier manual trans....stuck in reverse


You need to remove top off gearbox and with a pry bar or screw driver pull the selector back into neutral Your gearlever has popped out of selector Gearbox does not need to be removed

Jul 09, 2009 | 1991 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...