Question about 2003 Jeep Wrangler

Open Question

My overdrive switch in my 2003 jeep wrangler is broke , i need to replace it with a new one, can it be done diy

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
JustJeeps
  • 74 Answers

SOURCE: How do I replace the interior LH door handle 97 Jeep Wrangler?

you will need a t-20 or t-15 torx bit driver to remove 2 screws holding the handle this is all that holds them on, on once you have a replacement handle it is easier to remove 2 lower screws on the door panel and unsnap the door panel to loosen it this will allow space making it easier to reinstall new handle just slide each end into the slot and reinsert 2 screws to not fully tighten until door panel is snapped back in. the panel is held on with clips and can be released using plastic pry tool around door panel edges.

Posted on Nov 28, 2008

Ad
  • 5 Answers

SOURCE: how to install a new radio in a 2002 jeep wrangler

if you buy your radio from a reputable dealer he will have the correct wiring adapters and mounting hardware for your vehicle. with the correct equipment it will be a breeze

Posted on Jul 24, 2009

canbruce75
  • 1776 Answers

SOURCE: 2003 jeep wrangler eva canister diagram

Go to the autozone website at autozone.com and register your vehicle. It doesn't cost anything and you will have access to a full online repair manual for the vehicle. There should be the information you need there. Hope this helps and best wishes.

Posted on Jul 24, 2009

  • 1 Answer

SOURCE: Upgrading '84 CJ7 Headlight Switch with newer Wrangler Dash Switc

They work on the same principal, so as long as the amps and volts match up on the switch they should.however you will have to "eyeball" the size to see if the newer one will adapt right.

Posted on Oct 13, 2009

  • 31 Answers

SOURCE: 2001 jeep wrangler oil pressure sensor switch

Use an extractor designed for removing broken pipe fittings and broken bolts. They're often called bolt extractors and are available from tool merchandisers. Sears probably sells them as well as auto parts stores.

Posted on Jan 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is the overdrive switch the same in a 2003 jeep wrangler & 2008 jeep jk


same , as in location
or same as in , same gear ratio?
and there are many submodels of jk, like rubicon?
what is your concern?

May 22, 2014 | 2003 Jeep Wrangler

1 Answer

Replaced fuel pump and it keeps popping out why?2003 jeep wrangler


Does it lose power under acceleration? When you changed the pump did you change the strainer also? You should change the fuel filter if you have not done so. The other thing to check would be the fuel pressure regulator.

Mar 06, 2012 | 2003 Jeep Wrangler

1 Answer

High beam indicator light on, no low beams only high beams 2003 jeep wrangler


Replace the dimmer switch. Contact may be fused together if the column stalk switch has no effect.

Feb 12, 2012 | 2003 Jeep Wrangler

1 Answer

Need to replace the battery on my 2003 jeep wrangler.is there any special way


DISCONNECT THE NEGATIVE CABLE FIRST, RECONNECT IT LAST THING WHEN YOU ARE DONE

Jan 05, 2011 | 2003 Jeep Wrangler

1 Answer

Replace oil pan on 2002 wrangler 4.0


Hi you will have to remove the exhaust and then remove the oil pan then you can use a spanner to hold the nut and remove the oil plug

Nov 08, 2009 | 2003 Jeep Wrangler

1 Answer

Windshield wiper lever broke off steering column in 89 Jeep wrangler. How do you fix


If it's a multi-function switch or a single function arm, you will need to remove the steering wheel to access the attachment points. If you never have done this, get a basic manual such as haynes or chilton. Both have decent instructions to guide you and after, they have lots of good info to help with other problems as well. Since it's an 89, it's doubtful if it has an airbag...that makes things a lot less complicated.

Oct 29, 2009 | 1989 Jeep Wrangler

1 Answer

The blinker stick broke off in my 1987 Jeep Wrangler. How do i replace it?


remove steering wheel-and shroud then unscrew blinker assy and uplug wires-replace with new assembly-inless you can bodgey up with araldite or similar

Sep 13, 2009 | 1987 Jeep Wrangler

1 Answer

Wind sheid wipers malfunction on new Jeep Wrangler


U will need to replace the switch for wiper and turn signals, there is a broken contact inside the switch.

Apr 30, 2009 | 2008 Jeep Wrangler

Not finding what you are looking for?
2003 Jeep Wrangler Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...