Question about Ford F-250

1 Answer

I just wanna know where all the bolts i removed go back to? 1988 Ford F250 with a 460. Water pump bolt diagram.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 450 Answers

Go to a auto parts store they should help you

Posted on Sep 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and install water pump on 1988 ford ke laser


You have to remove your belt ...fan ...and fan shroud then remove outer bolts off water pump housing take off replace with new water pump and GASKET, seal gasket with permatex before placing gasket in place then rebolt new water pump on and your golden.....make sure no dirt or debris gets in ...im glad i can help ...

May 25, 2011 | Ford Laser Cars & Trucks

1 Answer

I need to replace oil pump on a 1988 ford bronco 2


Remove oil pan, making sure to drain oil first. Remove oil pump attaching bolts. Lift off oil pump and withdraw oil pump drive shaft.
INSTALLATION;
Prime the new oil pump by filling either the inlet or outlet port with engine oil. Rotate the pump shaft to distribute oil within the pump body. Insert oil pump drive shaft into block dwith the pointed end facing inward. The pointed end is closest to the pressed-on flange. Place oil pump into position with a new gasket and install attaching screws. Tighten the screws to 15-22 foot pounds of tourque. Clean and install the oil pump inlet tube and screen assembly with a new gasket. Tighten the bolts, then replace the oil pan.
Oil Pan;
Clean of any debris and replace gasket. Fit the oil pan bolts and tighten in two steps. Start from the rear/left hand side and tighten first, then tighten the bolt in the front/right side. Alternate from rear to front, working from back to front and front to back.

Oct 06, 2010 | 1988 Ford Bronco II

1 Answer

I would to replace the water pump on a 1988 6.2 chevy suburban ?


Hi Friend: I think your asking how to replace your water Pump. OK 1st Thing you'll need to do is Drain your Coolant/Water From Your Engine. With A Drain Pan Under Front of Vehicle Below your Lower Radiator Hose. Take the Hose Clamp Loose enough to Remove the Lower Radiator Hose from Your Water Pump.Your Coolant Will Come Out. 2nd Step Remove Your Drive Belt You can Remove this Belt by taking a 1/2 Inch Drive Socket and Correct Socket Size and Put it on The Center Bolt of your Belt Tensioner and Pull the Tensioner to Release the Pressure on Your Belt,While Holding it at that Poition Reach over to your Belt and Take it Off Say Your Alternator or A/C Compressor, Once you have removed it from Thee Release the Tensioner and Now you Can Work the Belt Out And Away From Your Pulleys that it Ran On. 3rd Now You'll need to Remove your Cooling Fan thee should be 4- Bolts and Nuts You'll Have takje all 4 out Then remove your Fan from Engine Compartment. 4th Your Going to Be able to See your Water Pump now You'll Also see that a Bracket or 2 From Your Power Steering and A/C Compressor are Bolted in Front of your Water Pump, So Remove any Brackets Or Components away from your Water Pump. Now that you have Remove anything in the way of your Water Pump including your upper Radiator Hose. You will Be Able to Take your Water Pump Bolts Out.Remeber where your bolts came out ,Some will be a Little Longer or Shorter.and will need to be put back in the same position. Ok Now All Bolts Are Out Of water pump Assembly, It might come right off ,if not just tap it with a Rubber or Plastic Hammer or take a Flat Screw Driver and Pry It off and away from Your engine. Clean the Surface on your engine of any gasket material or anything else.Completely Cleaned. Your New Water Pump will come with new Gaskets ,put some Gasket Sealer on the Water Pump and Put the Ne Gaskets on correctly by Lining up your Bolts Holes.Let It Set awhile,So Gaskets don't Slip when Mounting it to your Engine,Right Before you go to put the Water Pump on,Put a Little gasket sealer on the Gasket Area, Then Lining up your Holes Start Putting Your Bolts Back In All Bolts Should be Torqued at 40 Foot Lbs.Now to Finish installing the Rest of your Parts. Simply Reverse the Removal of The Water Pump. Hope i have helped you Please Let me Know on How my Solution Has Helped. Thank You: From =d_hubbs

Jun 08, 2010 | 1988 Chevrolet Silverado 2500

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

1 Answer

2002 ford taurus wtaer pump


Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
    4. Install the support bracket.
    5. Install the accessory drive shaft tensioner.
    6. Install the generator.
    7. Install the roll restrictor bracket, bolt and the nut.
    8. Install the water pump pulley.
    9. Install the accessory drive belt.
    10. Connect the battery ground cable.
    11. Fill the engine cooling system.

9de9feb.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Jul 04, 2009 | 2002 Ford Taurus

1 Answer

88 F150 320 automatic...


try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 18, 2009 | 1988 Ford F 150

1 Answer

How to change the water pump on a ford escort 1.3gle 1986 model


  1. Let me know if you cannot see diagrams(happens sometimes) or if you have any questions
Just to make sure. I assume that you are seeing coolant leakage from around the water pump assembly.

  1. Disconnect the negative battery cable.
  2. Place fender covers on the aprons.
  3. Drain the cooling system.
  4. Remove the accessory drive belts.
  5. Remove the timing belt cover.
  6. Use a wrench on the crankshaft pulley to rotate the engine so No. 1 piston is on TDC of the compression stroke.
Turn the engine only in the direction of normal rotation. Backward rotation will cause the timing belt to slip or lose teeth.
  1. Loosen the belt tensioner attaching bolts, then secure the tensioner over as far as possible.
  2. Pull the belt from the camshaft, tensioner, and water pump sprocket. Do not remove it from, or allow it to change its position on, the crankshaft sprocket.
WARNINGDo not rotate the engine with the timing belt removed or serious engine damage could occur. The 1.3L and 1.6L engines are of the "interference type," meaning it is possible for the valves to contact the pistons if their reciprocation is not carefully timed and controlled. An engine allowed to spin freely without the timing belt could bend valves and scuff pistons almost instantly.
  1. Remove the camshaft sprocket.
  2. Remove the rear timing cover stud.
  3. Remove the heater return tube hose connection at the water pump inlet tube.
  4. Remove the water pump inlet tube fasteners and the inlet tube and gasket.
  5. Unfasten the water pump to the cylinder block bolts and remove the water pump and its gasket.
0900c1528008b2ee.jpgFig. 1: If equipped, remove the cover from the water pump 0900c1528008b2ef.jpgFig. 2: Unfasten and remove the heater return tube hose connection at the water pump inlet tube nuts from the studs 0900c1528008b2f0.jpgFig. 3: Location of the water pump mounting bolts-1.9L engine 0900c1528008b2f1.jpgFig. 4: After unfastening the water pump retaining bolts, remove the water pump from the engine compartment 0900c1528008b2f2.jpgFig. 5: If you are reusing the old water pump, remove the gasket ... 0900c1528008b2f3.jpgFig. 6: ... and carefully clean both of the water pump mating surfaces using a gasket scraperTo install:
  1. Make sure the mating surfaces on the pump and the block are clean.
  2. Using a new gasket and sealer, install the water pump. Tighten the bolts to 30-40 ft. lbs. (40-55 Nm) on 1981-87 models, or to 15-22 ft. lbs. (20-30 Nm) on 1988-90 models. Make sure the pump impeller is able to turn freely.
  3. Install the water pump inlet tube and the inlet tube gasket and fasteners.
  4. Install the rear timing cover stud. Install the heater return tube hose connection at the water pump inlet tube.
  5. Install the camshaft sprocket.
  6. Install the belt from the camshaft, timing belt tensioner, and water pump sprocket.
0900c1528008b2f4.jpgFig. 7: Radiator hose-to- engine mounted water pump inlet tube-gasoline engines 0900c1528008b2f5.jpgFig. 8: Exploded view of common water pump inlet tube and related fasteners-non-A/C type 0900c1528008b2f6.jpgFig. 9: Exploded view of water pump and related components-1988-90 1.9L engineDo not rotate the engine with the timing belt removed.
  1. Tighten the belt tensioner attaching bolts, then secure the tensioner over as far as possible.
  2. Install the timing belt cover.
  3. Install the accessory drive belts.
  4. Refill the cooling system and reconnect the negative battery cable.

Nov 15, 2008 | 1983 Ford Escort Gt

1 Answer

Water pump


I don't have pictures for you but here is instructions:
Drain all the coolant.
Jack up the car on the front passenger side.
Remove the passenger side wheel.
Put a jack under the oil pan.
Detach the engine mounts on the passenger side of the car.
Remove all external belts.
Remove the upper timing belt cover bolts
Lower the engine using the jack.
Remove the water pump pulley. (3 bolts)
Remove the upper timing belt cover.
Disconnect the coolant line running across the front of the engine from the water pump. (2 bolts on a flange)
Pull the timing belt.
Pull the water pump.
Installation is just reversed.

If you need images, go to your local library. I never bought a manual, where is the fun in that? LOL plus everything I need to know can be found on the internet.

Oct 11, 2008 | 1989 Ford Festiva

1 Answer

Water pump


A manual will have pictures and everything.
Just replaced mine. Five bolts in bracket holding tension idler, A/C compressor (if applicable) and power steering pump must be removed to access 3 bolts in water pump. Just push aside enough to access remaining bolts. Email at dabeam@sbcglobal.net if additional info is needed. Also, diagram serpentine belt before removing. Took me at least 15 attempts and 20 minutes to figure out

Jun 25, 2008 | 1989 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...