Question about Acura Integra

1 Answer

Im replace a head on a 1990 acura integra b18a engine can i reuse the same head bolts

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

No, always use new head bolts/head studs
Acura recommends this at every head gasket service unless previously replaced at last head gasket service....
I reccomend ARP head studs or equivalent quality

Posted on Jan 17, 2014

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Jay_from_Ma
  • 99 Answers

SOURCE: belt replacement 1990 acura integra

Ok, you will need a 10 mm socket and extension and a 14 and 15 mm wrench. One of the "idler" pullies is actualy an adjustable tension pully. loosen the center nut on the pully, and then begin loosening the 10 mm bolt from above. as you loosen it, the pully will drop, and soon enough you can slip the belt off.
good luck

Posted on Dec 14, 2008

txkjun
  • 409 Answers

SOURCE: special bolt on the crankshaft pully on 1990 acura integra

It should be a hex bead bolt. Nothing really special about the. If its a bolt that is torqued then tightened to a specific angle then you need to replace it when doing the work.

Posted on Dec 31, 2008

  • 16 Answers

SOURCE: Trying to find out what

bro., what do you mean in the crankshaft? just go to pick n pull and put it in your pocket and walk out.

Posted on Feb 22, 2009

  • 153 Answers

SOURCE: timing belt diagram fo 1990 acura Integra

78338863have fun

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove the starter


three bolts.

Starter is at the back of the engine (left hand side) tucked in.

One bolt to remove the earth wire (12mm) i think
Two bolts (top and bottom of the starter) 14 or 16mm bolts
undo those
pull them out
yank off the starter
replacement is the reverse

Sep 07, 2013 | 1990 Acura Integra Hatchback

1 Answer

What is the torque spec's on a acura integra gs 90 motor ?


1990-1991 OBD0*
Engine: B18A
Cylinder Arrangement: Inline 4 Cylinders, Transverse
Type: Water cooled, 1.8L, 4 cylinder, 16 valve, DOHC
Displacement: 111.9 cu in (1834 cc)
Bore & Stroke: 3.19 in x 3.50 in (81mm x 89mm)
Compression Ratio: 9.2 : 1
Valve Train: Double Overhead Camshafts, Belt Driven
Fuel System: Programmed Fuel Injection (PGM-FI)
Horsepower: 130 hp @ 6000 rpm
Torque: 121 lbs.-ft. (16.8 kg-m) @ 5000 rpm
Redline: 6500 RPMs
Engline Block: Aluminum Alloy with Cast Iron Cylinder Liners
Cylinder Head: Aluminum Alloy

Jun 24, 2010 | 1990 Acura Integra Hatchback

1 Answer

Replacing my pcv valve


Under hood, center, upper engine area, between throttle body unit and valve cover, base of center vacuum hose, mounted in intake manifold

Mar 30, 2010 | 1990 Acura Integra Hatchback

1 Answer

I have a 94honda civic witha b18a1 and


well a b18a is from a 90 to 93 integra, b18b is from 94-01 integra and lsd may be stamped on case, or if u remove the half shafts there will be and open hole tru the differential

Mar 02, 2010 | Acura Integra Cars & Trucks

1 Answer

I'm trying to replace the power steering pump on my acura integra 1994 how can i replace it


drain power steering fluid.disconnect the inlet and out let hoses from power steering pump.remove belt by loosen the adjusting bolts on pump bracket.remove power steering bolts and remove pump.put in new power steering pump torque it 17 ft lbs . connect hoses .put belt back on adjust the belt tension. add fluid check level . bleed the air from system.

Apr 13, 2009 | 1990 Acura Integra Hatchback

1 Answer

Trying to find out what the special bolt is on the crankshaft on my 1990 acura integra


bro., what do you mean in the crankshaft? just go to pick n pull and put it in your pocket and walk out.

Dec 31, 2008 | 1990 Acura Integra Hatchback

1 Answer

Special bolt on the crankshaft pully on 1990 acura integra


It should be a hex bead bolt. Nothing really special about the. If its a bolt that is torqued then tightened to a specific angle then you need to replace it when doing the work.

Dec 30, 2008 | 1990 Acura Integra Hatchback

1 Answer

Belt replacement 1990 acura integra


Ok, you will need a 10 mm socket and extension and a 14 and 15 mm wrench. One of the "idler" pullies is actualy an adjustable tension pully. loosen the center nut on the pully, and then begin loosening the 10 mm bolt from above. as you loosen it, the pully will drop, and soon enough you can slip the belt off.
good luck

Dec 14, 2008 | 1990 Acura Integra Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...