Question about 1995 Chevrolet G20
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Does your van have the serpentine belt? If so maybe I can help, I replaced the Power steering pump on my 90 G20 a couple of weeks ago. The trick is that you need to pull the pump pulley which is pressed on to access the mounting bolts which attach the pump to the engine. Harbor Freight tools sells a great tool designed for this job for $20.00. Once you have the correct tools, remove the serpentine drive belt. You may also need to remove the fan shroud. the pump shaft looks like it has an allen socket in the center, but this is for use in the manufacturing process, and will not come out. Place the puller tool on the pulley following tthe instruction that come with the tool, and remove the pulley. loosen, but do not remove the nut on the high pressure hose connection. use a pair of **** pliers to cut and remove the crimp clamp on the low pressure hose. If your pump has the remote reservour loosen the clamp on the reservour hose also. Remove the three mounting bolts, place a large pan under the pump to catch drips, and remove the prevously loosened hoses. there will be fluid leaking all over and the pump should come free, There are two types of replacement pump sold. With and without reservour. This reservour is a metal cover that fits over the back of the pump, and should not be confused with the reomte revervour found on some newer models which is next to the battery. This reservour is held in place be two throught the pump bolts which are removed at the back of the pump. If your new pump has a reservour you will probably still need to remove these bolts and put them in the replacement pump as most are shiped without these bolts. If you replacement pump comes without a reservour pull the bolts, the reservour should pull off of the old pump and slide onto the new one. check the o rings and replace the through the pump bolts. Installation is the reverse of removal execpt that 1/2" hose clamps replace the crimp clamps on the low pressure hose, and the puller tool is set up differently to replace the pulley. Finally if you don't flush contaminants out of the system your repair will last maybe a week. www.cardone.com has a great article about power steering flushing, read it before you start Good luck.
Posted on May 15, 2008
I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.
Posted on Apr 09, 2009
If the distributor hasn't been taken out, the timing can be set manually but you have to disconnect the distributor wire behind the glove box inside the cab. Tan wire with white tracer it is taped up to the a multi wire harness but is the only one with a single plug. Disconect the plug and use your timing light on the timing mark to set timing per specs. Rotate the distributor as needed to advance or retartd as required for the correct setting. tighten the dizzy clamp and plug the tan wire back together. The computer will now be fooled asd to what the base timing is and advance from there.
Contrary to popular belief, 96' and up do not have this wire. Timing has to be done with a programmable scanner.
Hope this helps.
Posted on Apr 25, 2009
you will need some fairly long wrenchs 15mm-16mm to get leverage on the spring loaded serp tesiner put a wrench on the pulley near the belt ? also loosen the 4 fan bolts on the water pump before you remove the belt ? ther are 7 fan shroud bolts you can split the fan shroud ? 2 bolts on the lower right and 2 on the left ? after you do this then you should be down to pulling off the fan and pulley just slides off ? then remove the 4 waterpump mounting boltss, scrape the old gaskets ? when this is done all you have left is to installthe fan studs from the old pump? you do this by screwing down 2 nuts on the stud then with 2 wrenchs lock the nuts together ? then unscrew the bottom nut ? keep doing that till all 4 are replaced? install the gaskets and add some silicone and reverse the process ? hope this helps repost thumbs up !!
Posted on Aug 29, 2009
You actually have two separate problems. The brake pull to the right is indicating the left side brake is not working properly. You will want to remove the left front wheel, collapse the caliper piston and make sure the caliper is floating freely on its mounts.
With the piston collapsed you should be able to slide the caliper inboard and outboard of the rotor. If not, you will want to remove the attachment pins, clean and lubricate the pins. If they are grooved or worn you will have to replace them.
The second issue of the ABS light is indicating the system has detected an electrical sensing or control problem. Take the vehicle to your local Auto Zone or Advance Auto and ask them to scan the vehicle for trouble codes. They will scan it for you at no charge.
Chances are you will find a wheel speed sensor problem at one of the wheels.
Write the codes down and respond back, we can start diagnosing the problem,
Good luck, let me know.
Posted on Aug 31, 2009
Tips for a great answer:
Jun 25, 2017 | Cars & Trucks
Feb 27, 2015 | 1995 Chevrolet G20
Feb 27, 2015 | 1995 Chevrolet G20
Jan 29, 2012 | Cars & Trucks
Feb 08, 2011 | 1995 Chevrolet G20
Jan 24, 2011 | 1995 Chevrolet G20
Nov 06, 2009 | 1995 Chevrolet G20
Aug 23, 2009 | 1995 Chevrolet G20
Jun 18, 2009 | 1995 Chevrolet G20
131 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: