Question about 1993 Geo Tracker

Open Question

How to replace the front wheel bearing on a 95 tracker 4x4

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 72 Answers

SOURCE: 1995 4x4 geo tracker front wheel bearings

first you remove the wheel then the break caliper then remove the locking hubs just remember to lay out the parts in order a special tool is called for but this job can be done without it you have to use a small cold chisel and a hammer to tap the large nut counter clockwise to remove, you can then remove the outer bearing and the rotor and hub assembly look on the back side reomve the bearing seal and inner bearing be sure to pack your new bearings with grease before you reassemble . takes less than an hour.

Posted on May 05, 2010

Ad
perkins48
  • 14380 Answers

SOURCE: How do I replace the

  1. Loosen all of the front/rear wheel lug nuts 1 / 2 turn.
  2. Apply the parking brake, block the rear wheels, then raise and safely support the front of the vehicle on jackstands.
  3. Remove the wheels.
    1. If equipped with 4WD and automatic locking hubs, perform the following:
    1. Unscrew the automatic hub cover and remove the cover and O-ring.
    2. Remove the hub assembly mounting bolts and remove the hub assembly.

    1. If equipped with 4WD and manual locking hubs, perform the following:
    1. Remove the six manual hub cover mounting bolts and remove he manual hub cover and gasket.
    2. Remove the six manual hub mounting bolts.
    3. Remove the manual hub and O-ring.

  • perkins48_952.jpg

    Fig. Fig. 8: To remove the wheel hub and bearings, first remove the bearing lock plate which is secured by four screws .

    1. Remove the caliper mounting bracket and position the caliper out of the way. Support the caliper.
    2. Remove the brake rotor from the wheel hub. Remove the front wheel bearing lockplate screws, lockplate and washer.
    3. Remove the wheel bearing locknut and washer, then remove the wheel hub complete with bearings and seals.


    perkins48_953.jpg

    Fig. Fig. 9: Remove the wheel bearing locknut and washer using the special tool shown .
    If wheel hub cannot be removed by hand, use special tool J3781 with a J2619-01 for the Tracker or 0999-1511 with 09930-30102 for the Sidekick, Sidekick Sport and X-90 models, or their equivalents. These tools are a hub remover and sliding hammer.


    perkins48_954.jpg

    Fig. Fig. 10: A slide hammer may be necessary to remove the assembly from the spindle .

    1. If equipped with ABS brakes, remove the sensor rotor from the wheel hub.

    Pull out the sensor rotor from the wheel hub gradually and evenly. Pulling it out partially may cause it to deform.

    perkins48_955.jpg

    Fig. Fig. 11: Cross-sectional view of the front wheel hub and bearing assembly .

    1. Remove the inner bearing grease seal.


    perkins48_956.jpg

    Fig. Fig. 12: To remove the bearing from the hub, remove the snapring and rear oil seal ...



    perkins48_957.jpg

    Fig. Fig. 13: ... then press the bearing assembly out of the wheel hub .

    1. Remove the snapring and remove the inner bearing.
    2. Clean and inspect the hub and bearing seats.

    To install:

    1. Install the inner race, wheel bearing snapring and seal in the hub. Apply lithium grease to the lip portion of the oil seal.



    perkins48_958.jpg

    Fig. Fig. 14: Press the new bearing into the wheel hub until it contacts the stepped surface of the hub .

    1. If equipped with ABS brakes, install the sensor rotor.
    2. Install the hub on the spindle and install the outer bearing, locknut, washer, and lockplate. Tighten the locknut to 123-180 ft. lbs. (170-216 Nm).


    perkins48_959.jpg

    Fig. Fig. 15: Drive in the two wheel hub oil seals. If the tool shown is not available, you may need to install the seals one at a time .



    perkins48_960.jpg Fig. Fig. 16: Apply lithium grease to the wheel hub seals as shown .

    1. Install the four lockplate mounting screws. Tighten the screws to 8.8-17.7 inch lbs. (1-2 Nm).
    2. Install the brake rotor.
    3. Install the caliper and tighten the bolts to 61 ft. lbs. (85 Nm).
    4. If equipped with 2WD, install the locking hub cap.
    1. If equipped with 4WD and automatic locking hubs, perform the following:
    1. Install a new O-ring on the hub assembly.
    2. Install the hub assembly onto the wheel flange. Make sure the tab on the hub fits into the notch on the spindle.
    3. Install the six mounting bolts and tighten to 18 ft. lbs. (25 Nm).
    4. Install a new O-ring on the hub cover.
    5. Install the hub cover.

    1. If equipped with 4WD and manual locking hubs, complete the following sub-steps:
      1. Install a new O-ring on the manual hub body.
      2. Install the manual hub onto the wheel flange and install the six mounting bolts. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).
      3. Install a new gasket on the manual hub cover.
      4. Install the hub cover on the hub. The lever must be in the FREE position with the clutch pulled out toward the cover.
      5. Install the six mounting bolts. Tighten the bolts to 71-106 inch lbs. (8-12 Nm).

      6. Install the wheels and lower the vehicle.
      7. perkins48_961.jpgTIMKIN/WHEEL BEARING-FRONT,NOTES; INNER BEARING,2 REQUIRED,PART#517009 FOR 50.99 AT AUTOZONE.

    Posted on May 10, 2011

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Can't get my 95 Geo Trackers 4WD to work. The indicator light works still but the wheels themselves won't engage. Can anyone plz help me out with what might be my problem?


    For Trackers (and Sidekicks) of this era (1989 to 1998) the front axle locking device is a locking hub on each front wheel. (There are no actuators until the model change in 1999.) Locking hubs come in two flavors, Manual and auto locking hubs. A look at the from wheel should tell you what you have. Manual hubs have a knob like lever with the word "lock" and "free." Auto hubs say "Auto-Locking" right on them. Both types of hubs require servicing periodicity. (Normally annually.) This means removing and disassembling. Then cleaning and light greasing before reassembling. There are some good videos on the web on how to service the manual hubs. Auto hubs are a little harder to ensure they are working properly, but some people like them. (Not me.)

    Please note two things:
    1. Due to differential action, BOTH hubs need to be locked for any power to be applied to the front wheels.
    2. Trackers of this era are PART TIME 4x4, NOT all wheel drive. They have nothing providing for different wheel speeds front to back like a center differential. This means they should NOT be used on non-slippery surfaces like dry pavement. Beside causing handling and braking issues, it can destroy your transfercase driving on dry pavement in 4x4 due to what is called "driveline wind up".

    PLEASE if you do not understand this, look it up... if you still do not understand, ask and do not use the 4x4 until you do.

    Feb 18, 2015 | 1995 Geo Tracker

    1 Answer

    How to repack front manual hub bearings on 1993 tracker 4X4


    every fact on topic , hubs here.

    it's not the locking hubs its the wheel bearings in its own hub.
    http://www.fixkick.com/

    dangerous condition that... very much so.

    May 24, 2014 | 1993 Geo Tracker

    1 Answer

    Front bearings and seals on 95 geo tracker replacement


    Click here to see how to replace front wheel bearing.Here are the bearings.

    Dec 16, 2012 | Cars & Trucks

    1 Answer

    How do I replace the rear wheel bearing on a 1991 Geo Tracker 4x4.


    with a bearing puller & press. Don't do it unless u have experienced it. I know it stinks but YA GOTTA DO WHAT YA GOTTA DO. Good luck

    Jul 25, 2017 | Geo Tracker Cars & Trucks

    1 Answer

    1995 4x4 geo tracker front wheel bearings


    first you remove the wheel then the break caliper then remove the locking hubs just remember to lay out the parts in order a special tool is called for but this job can be done without it you have to use a small cold chisel and a hammer to tap the large nut counter clockwise to remove, you can then remove the outer bearing and the rotor and hub assembly look on the back side reomve the bearing seal and inner bearing be sure to pack your new bearings with grease before you reassemble . takes less than an hour.

    May 05, 2010 | 1995 Geo Tracker

    1 Answer

    95 nissan 4x4 truck. four wheel drive light comes but does'nt en


    the front axles have pinon gear box that the shaft from the transfer case goes to, it has a vacuum hose to it or a solenoid actuator check these for proper function this is how the power is turned on to the wheels.

    Feb 13, 2010 | 1990 Nissan Hardbody King Cab

    5 Answers

    Cannot find tool to loosen front wheel bearing lock nut


    I have a 1995 Geo Tracker 4WD with the same exact problem,However I did some research . You will need to go to the Kent Moore Website which makes specialty tools and look up Wheel bearing socket "J-37763" I saw the picture of it and it looks like there are 4 small rounded teeth/tabs. Unfortunately get ready to spend some money - cost is about $70.00 not including shipping/handling
    I hope that this Info. helps - Jim H.

    Apr 06, 2009 | 1995 Geo Tracker

    1 Answer

    RELACING WHEEL BEARINGS IN A 95 JEEP GRAND


    Front wheel bearings can be done at home rear wheel bearings will require a hydraulic press and an axle puller. Either job can be difficult depending on amount of rust and availability of tools. The front wheel bearings are an assembly and once the jeep is up on jack stands, with the tires, brake calipers, and rotors removed, it is only a matter of removing the axle nut and 3 bolts (which can be difficult depending on rust) holding in the old bearing assembly

    Feb 22, 2009 | 1995 Jeep Grand Cherokee

    1 Answer

    Replace wheel bearing (front-driver) on '93 Geo Tracker 4x4 (Details)


    http://carfix.stufftoread.com/

    see front wheel bearings and hubs here.

    Sep 26, 2008 | 1993 Geo Tracker

    1 Answer

    Replace wheel bearing - '93 Geo Tracker 4x4


    http://carfix.stufftoread.com/

    see bearing and hubs.

    full spec

    Sep 26, 2008 | 1993 Geo Tracker

    Not finding what you are looking for?
    1993 Geo Tracker Logo

    Related Topics:

    95 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Geo Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8522 Answers

    Are you a Geo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...