Question about 1993 Buick Regal

1 Answer

How do you put on alternator belt - 1993 Buick Regal

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 8,215 Answers

Route the belt as shown below (from autozone.com) but leave it off of the alternator. Use an 18mm wrench or socket on the tensioner pulley and pull toward the front of the car. With the tensioner pulled down, slip the belt onto the alternator completing the diagram. Check routing to verify that belt is still riding on all pulleys.


how do you put on alternator belt - 3236223.jpg

Posted on Sep 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car keep on breaks alternator belts and it also makes this loud whistling noise. I've put on a new water pump, 3 alternators and several alternator belts


make sure that the pulleys of all the driven equipment are in alignment and not at a bit of an angle to the axis of the drive belt
To break belts something is not lined up properly or something is not turning freely

Dec 31, 2015 | 2000 Mazda Protege

1 Answer

My mazda protege keeps breaking alternator belts. I've put on serval alternator belts, a new water pump pulley, and 3 alternators and my is still breaking belts


Replace belt tensioner, any other pullys, I worked on ? vehicle where the pully would spin but would stop every so often.

Dec 31, 2015 | 2000 Mazda Protege

1 Answer

How to replace alternator on 2001 olds aroura


Disconnect battery (always neg pole/post first)
find alternator, loosen belt.
disconnect wiring @ alternator.
take alternator off.
put alternator in place of it
put belt on tighten all screws, belt tension screw first.

Jan 13, 2015 | 2001 Oldsmobile Aurora

2 Answers

1998 Isuzu trooper 3.5 alternator replace


step one remove battery neg lug .
the above video (of book?) is wrong.
the belt tension-ing step was skipped.

remove belt steps remove alt. wiring. remove alternator (bolts) it falls free. replace it , reverse steps above belt back tension belt. battery cable back. test run. charge/BAT lamp off?
see wrench below, turn it CW.
this releases the spring tension and belt comes off
to put back, do same and put on belt and release wrench.

25186758-dk3xh54xw1fmpqbxyhqoyzal-4-0.jpg3.5L only. USA only.

Oct 05, 2014 | Isuzu Trooper Cars & Trucks

1 Answer

Putting the alternator belt on a montero sport


FOR 3.0LENGIBE. PUTTING ON ALTERNATOR BELT YOU NEED TO LOOSEN LOCKING BOLT IN SLOT IN THE BRACKET.LOOSEN PIVOT NUT BOTTOM NUT USE A PRY BAR PRY AGAINST ALTERNATOR TO TIGHTEN BELT TENSION. BELT SHOULD DEFLECT 1/4 TO 1/2. FOR 2.4L ENGINE TO GET ALTERNATOR BELT ON YOU NEED LOOSEN THE PIVOT BOLT OR NUT AT THE BOTTOM OF ALTERNATOR , LOOSEN THE LOCK BOLT AND TURN THE ADJUSTER BOLT TO TIGHTEN ALTERNATOR BELT THE BELT DEFLECTION SHOULD BE 1/4 TO 1/2 INCH WHEN YOU PRESS DOWN WITH THUMB.

Oct 02, 2011 | 1999 Mitsubishi Montero Sport

1 Answer

How do I change a alternador in my 1999 plymoth Breeze 2.0


1 remove battery cables from battery 2 disconnect wires from alternator 3 loosen belt with the belt tensioner it will probly take a 3/8 drive ratchet to loosen the tensioner by putting the end that normaly goes into socket into a square hole in tensioner( just move tensioner far enough to slip belt off alternator pully) 4 remove bolts from alternator 5 put new alternator in place and put bolts in 6 put belt back over pulley 7 plug wires back on alternator 8 reconnect battery

Oct 01, 2011 | 1999 Plymouth Breeze

2 Answers

85 chevy c-10 silverado. How do put on an


on some models the belt ran around both if you do not have the old belt get a piece of string and wrap it around the pulleys for the alternator. have the alternator set about halfway on the adjustment bracket. two bolts hold the alternator one on the bottom and one on the top loosen both up enough to allow you to move the alternator but the belt on and rotate the alternator until tight enough you can't push it down more than a 1/4 of an inch.

Aug 30, 2009 | 1985 Chevrolet S-10

1 Answer

How do i REMOVE AND REPLACE THE ALTERNATOR ON MY 95 NISSAN MAXIMA?


TURN OFF RADIO TO KEEP FROM LOSING RADIO CODE.THEN YOU REMOVE NEGATIVE BATTERY CABLE.DISCONNECT THE 2 LEAD WIRES AND HARNESS CONECTOR FROM ALTERNATOR LOOSEN THE DRIVE BELT ADJUSTING BOLT AND REMOVE THE BELT. UNSCREW THE ALTERNATOR ATTACHING BOLTS AND REMOVE THE ALTERNATOR FROM VECHICLE.VISA VERSA PUT EVERY THING BACK.AND ADJUST ALTERNATOR BELT TENSION.WARNING DONT PUT TOO MUCH TENSION ON BELT.BECAUSE YOU WILL DAMAGE ALTERNATOR PULLEY BEARING.

Aug 01, 2009 | 1995 Nissan Maxima

1 Answer

My car is a VW golf Gti mk3 8v 2.0L, Alternator / water pump drive belt has snapped and been lost. I have new belt but I'm unsure of routing around the 3 pulleys. does the alternator act as the tensioner??


loosen the alternator and push the alternator to-wards the engine,put your new belt on ,fitting around the 3 pulleys once fitted look and see that the belt is in line.If your happy the belt is lined put a small bar between the engine and alternator and force the alternator out towards the front this should tension your belt tighten bolts on alternator.;at the longest point between two pullys in the middle of the belt move belt up and down with fingers if tension is right it should not move more than about 150ml,hope this helps you.adrian

Feb 02, 2009 | 1997 Volkswagen Golf

1 Answer

Alternator


Answer Use a large wrench to take tension off of your serpentine belt and remove the belt from the alternator, (just the alternator). Disconnect the wires. Remove the bolts then the alternator. Put new alternator in place using old bolts. Replace wires (may only be one wire, depending on the alternator). Get your large wrench back out, put the belt back on the alternator, and your good to go. this should do it.

Jul 09, 2008 | Hyundai Motor 1998 Sonata

Not finding what you are looking for?
1993 Buick Regal Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...